Bartscher 112081 Heated Middle Shelves Instruction Manual
- June 13, 2024
- Bartscher
Table of Contents
Bartscher 112081 Heated Middle Shelves
Product Information
- Product Name: Heated Middle Shelves
- Model: 2015 40 022
- Manufacturer: Made in Italy
- Power Supply Voltage: 220-240 V~ 1N
- IP Rating: IPX4
- Number of Phases: 1
- Liquid Protection Level: Protected against liquid splashes
- Power Supply Frequency: 50-60 Hz
- Max Power Input: 400W (2L), 600W (3L), 800W (4L)
- Cable Type: Mmq-H05RN-F
- Variation in Voltage: +/- 10%
- Variation in Frequency: +/- 1%
- Variation in Frequency (Short Period): +/- 2%
Product Usage Instructions
Installation and Commissioning
- The electrical installation should be carried out by a qualified electrician.
- Before making the electrical connections, follow these steps:
- The manufacturer is not responsible for any damages caused by connections made by the user or unqualified personnel.
- Dispose of the packaging according to the regulations in your country.
Main Rules The electrical installation should be carried out by a qualified electrician.
Use of the Appliance Follow the instructions provided in the user manual for proper usage of the heated middle shelves.
Disposal and Recycling of the Appliance At the end of the product’s life, dispose of the appliance according to the regulations in your country to avoid environmental pollution.
ORIGINAL INSTRUCTIONS
WARNING!: read carefully the instructions before using the appliance.
INSTALLATION DIAGRAM
WIRING DIAGRAM
INTRODUCTION
This section shows the symbols and provides information about the model of the
appliance, the various responsibilities and the copyright.
It concerns heated middle shelf.
For further information refer to paragraph “Technical data” (2).
DATA PLATE
- The data plate shows the identification and technical data of the product.
- The data plate is inside the appliance on the right upper part of the heating panel.
WARNING!
- Do not remove, tamper with or erase the “CE” mark of the appliance.
- Refer to the data on the “CE” plate of the appliance in all communication with the Manufacturer (for example: when asking for spare parts, etc..)
- The “CE” plate has to be destroyed while scraping the appliance.
The present handbook is intended solely for consultation by the operator. Its
content could be modified without notice. The Manufacturer reserves the right
to stop the manufacturing of any model and/or introducing product changes but
is not obliged to change products delivered before the modification and
declines all responsibilities for any inaccuracy may appear on this handbook
related to printing or translation mistakes.
The company cannot assume liability for damage and faulty operation due to:
- Failure to obey the instructions of this handbook;
- Modification or appliance alteration;
- Maintenance by unspecialized technicians ;
- Insufficient maintenance;
- Improper use of the appliance
- Exceptional and unforeseeable events;
- Unrespect to domestic legislation on health, hygiene and safety at the workplace;
- The employer is responsible for the periodic training of the operators about the correct use, safety rules and fire prevention.
TECHNICAL DATA
RANGE OF HEATED MIDDLE SHELVES 2L 3L 4L
| Supply voltage | V | 220-240 | 220-240 | 220-240 |
|---|---|---|---|---|
| Frequency | Hz | 50-60 | 50-60 | 50-60 |
| Max. power input | W | 400 | 600 | 800 |
| Max. current requirement | A | 1,8 | 2,6 | 3,5 |
| Power cord | Mmq-H05RN-F | 3×1,5 | 3×1,5 | 3×1,5 |
| Max. supply Voltage variation | +/- 10% | +/- 10% | +/- 10% | |
| Max. Frequency variation | continuous | +/-1% | +/-1% | +/-1% |
| Max. Frequency variation | Short period | +/- 2% | +/- 2% | +/- 2% |
WARNING!
The electric power system and the rooms where the appliance is placed have to
respect domestic legislation on safety, accident prevention and fire
regulations. On the contrary the Manufacturer won’t assume liability for
direct and indirect damages topeople or things.
INSTALLATION AND COMMISSIONING
Proceed according to the following instruction before connecting the appliance:
- Remove the packaging and then the protective film taking care not to scratch the surface;
- Make sure the power supply of the appliance shown on the data plate is compatible with the grid voltage;
- Check the power supply of the system is set up and able to take the current load, and meets the legal requirements and domestic standards;
- The appliance must be earthed;
- Plug the appliance. In case of direct connection to the electricity grid (without plug), it’s necessary providing for a wall switch, which grants the complete disconnection according to overvoltage III rate and accordingly to installation rules;
- Have the system tested by a qualified electrician, if operation of the equipotential earth connection or the safety of the electrical system is in doubt, the symbol below identifies the equipotential connection:
The Manufacturer declines all responsibilities in case of connection made by
the user or unspecialized staff.
WARNING!
After installation dispose of the packaging according to current regulations.
This appliance is designed and optimized to ensure high performance and
efficiency. The sole use of this appliance is keeping food heated.
WARNING!
- Contact with hot tableware can cause burns.
- Use always suitable safety equipment while handling objects.
MAIN RULES
The Manufacturer does not assume responsibility for faults or damage due to tampering the appliance. This appliance must be used by skilled persons that must be periodically trained for its correct use and according to the safety regulations and prevention of accidents. Contact with hot tableware in the appliance can cause health risks. In order to prevent them use safety equipment and act with suitable caution.
WARNING!
Intervention on the electric power system must be solely performed by
specialized electricians.
USE OF THE APPLIANCE
- Press the main switch on the supply panel that powers the appliance.
- Switch on the button “A” to position “I”. When the button “A” is switched on, it is lighted up and the appliance is under power and starts operating.
- To stop heating turn the switch to “O” position. The heating is so disconnected but the appliance is under power.
- Avoid amassing plates and place them under the lights.
- Switch off finally the main power supply line ahead of the appliance or plug the appliance off.
- Only when the appliance is disconnected, clean the stainless steel surfaces with warm water and a neutral soap, rinse thoroughly and dry carefully.
- In case of long period of inactivity, store the appliance in a dry place.
DISPOSAL AND RECYCLING
Dispose of the appliance responsibly and respect the environment at the end of its useful life. Proceed with its disposal in accordance with domestic regulation.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>