Godox 2ABYN102 Wireless Lavalier Microphone System User Manual

Godox 2ABYN102 Wireless Lavalier Microphone System

Warning

• This product is high-precision instrument, please avoid falling, collision or pounding .
• Do not disassemble. Should repairs become necessary, this product must be sent to our Company or an authorized maintenance center .
•  Always keep this product dry. Do not use in rain or damp conditions .
• Do not leave or store this product in the environment of direct sunlight, near heating devices, or in hot, humid or dusty .
• Keep out of reach of children .
• Do not use in flammable and explosive environments. Pay attention to the relevant warning signs
• Do not leave or store the product if the ambient temperature reads over 50″C .
• Please read carefully and follow the warnings or instructions provided by the manufacturer.

Structure of Product

Transmiter

1. Power Switch Button
2. Pairing/Denoise Button
3. Built-in Microphone
4. Back Clip
5. Indicator
6. Type-C Charging Port
7. Charging Points

Receiver

1. Power Switch Button
2. 3.smm Aud· 10 Output Port
3. Indicator
4. Type-C Charging Port
5. Pairing Nolume + Button
6. Mode Nolume – Button
7. Back Clip
8. Charging Points

Charging Case

1. Transmitter’s Slot
2. Receiver’s Slot
3. Indicator
4. Display
5. Type-C Charging Port
6. Reset Hole

What’s Inside

to Type-C Data Cable x1, Furry Windscreen x1, 3.5mm TRS-TRS Audio Cablex1, 3.5mm TRS-TRRS Audio Cable x1, Storage Box x1, Instruction Manual x1
Wireless Lavalier Microphone System| WECKit2| Transmitter x2, Receiver x1, Charging Case xl,

USB to Type-C Data Cable x1, Furry Windscreen x2, 3.5mm TRS-TRS Audio Cablex1. 3.5mm TRS-TRRS Audio Cable x1, Storage Box x1, Instruction Manual x1

Note: Due to continuous updates and upgrades of the products, there may be differences between the actual products and the pictures. Therefore, the pictures are for reference only, products to prevail in kind.

Instructions for Use

Power Switch

1. Operating Instructions
   Long press the power switch button< >for 3s to turn on or off the transmitter and receiver. Take out the devices from the charging case, they will boot up automatically, while put them into the charging case, they will be turned off.
   Note: The transmitter and receiver will be turned off if they stay unpaired in 5min after powered on.

2. Indicator Instructions

Pairing

1. Operating Instructions
   Long press the pairing/denoise button< >of transmitter and pairing/volume+ button< >of receiver for 2s to pairing them. They will exit pairing status once paired, while exit after 10s if unpaired.

2. Indicator Instructions

TX1 indicator of receiver is constant on green, TX2 indicator of receiver flashes green slowly every O.Ss and turns off in 1Os| One transmitter and one receiver are paired
Both indicators of receiver are constant on green| Two transmitters and one receiver are paired

Denoise

Operating Instructions
Short press the pairing/denoise button< >of transmitter to turn on or off the denoise function.

Indicator Instructions

Mode Switch

Operating Instructions
The sound track mode is mono by default, long press the mode/volume – button< M /- >of receiver for 5s can switch to stereo mode.

Indicator Instructions

Output Volume Adjustment
Short press the pairing/volume+ button< >or mode/volume – button< M /- >of receiver can adjust the output volume in 3 levels with an increment of 6dB each stop. The volume is the middle level by default after first boot.

Charging

Charging through Type-C Cable
The transmitter and receiver can be charged after connecting to power source through type-C cable.

is below 10%
TX1 indicator of receiver is constant on red, TX2 indicator of receiver displays normally| Battery levels of receiver and transmitter TX2 are normal, while battery level of transmitter TX1 is below 10″/4
TX1 indicator of receiver displays normally, TX2 indicator of receiver is constant on red| Battery levels of receiver and transmitter TX1 are normal, while battery level of transmitter TX2 is below10″/4
---|---
Both indicators of receiver are constant on red| Battery level of receiver Is normal, while battery levels of transmitter TX1 and TX2 are below 10%
Both indicators of receiver flash red every 0.5s| Battery level of receiver is below 10%

Charging through Charging Cable

• Put the devices Into the charging case and open the lid: The case will first detect whether the devices are correctly inserted into the corresponding slots, the corresponding indicators in the case will light up if the pins inside touched the charging points of the devices. Then it will detect whether the devices are fully charged, if not, it will start charging until the devices are fully charged. The indicators and number display wilt light up at the same time if the charging
  case lid is open, and turn off after the devices are fully charged in 5s.

• Put the devices Into the charging case and dose the lid: The devices will shut down and be charged until they are fully charged. The number display will be off in 1 min after closing the lid.

• Charging the case : The number display will increase gradually from Oto 100, and remain 100 after the charging case is fully charged.

devices
Indicators inside the charging case are constant on white| The devices are fully charged

Instructions for Installation

• Clip the transmitter to the collar with its back clip.
  

• Clip the receiver to the camera with its back clip, then connect the 3.5mm audio output port of receiver to the 3.5mm audio input port of camera with the 3.5mm TRS-TRS audio cable.

• Connect the 3.5mm audio output port of receiver to the 3.5mm earphone jack port of smartphone with the 3.5mm TRS-TRRS audio cable.

Technical Data

3.7V -1400mAh, 5.18Wh
Type-C Input| 5V -160mA| 5V -200mA| 5V- 1.3A
Working Time| Approx. Sh| Approx. 8h| Charge 3 devices for about twice
Charging Time| Approx. 2h| Approx. 2h| Approx. 2h
---|---|---|---
Working Environment Temperature| -10~50°C| -10-5o•c| -10-5o•c
Dimension| 48mmx22mmx16mm 1.89’•0 87″•0 63″| 48mmx28mmx15mm 189’•110•,059•| 63mmx85mmx3Qmm 243•,335•,118′
Net Weight: e| 12g| 16g| 84g

Specifications and data may subject to changes without notice

Maintenance

• Avoid falling. Strong collision or vibration may malfunction the device.
• Keep dry.
• This product is not water-proof. Malfunction, rust, and corrosion may occur and go beyond repair if soaked in water or exposed to high humidity.
• Avoid sudden temperature changes. Condensation happens in sudden temperature changes such as the circumstance when taking the product out of a building with higher temperature to outside in winter. Please put the product in a handbag or plastic bag beforehand.
• Keep away from strong magnetic field, The strong static or magnetic field produced by devices such as radio transmitters leads to malfunction.
• Specifications and data may subject to changes without notice.

FCC Statement

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. this device must accept any interference received, including interference that may cause undesired operation.

Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

Note:

• This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
• These limits are designed to provide reasonable protection against harmful interference in a residential installation.
• This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.
• If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
  • Reorient or relocate the receiving antenna.
  • Increase the separation between the equipment and receiver.
  • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
  • Consult the dealer or an experienced radio/TV technician for help.
• The device has been evaluated to meet general RF exposure requirement
• The device can be used in portable exposure condition without restriction.

Warning

• Operating frequency: 2402MHz – 2480MHz
• Maximum EIRP Power: 5dBm

Declaration of Conformity

• GODOX Photo Equipment Co.,Ltd. hereby declares that this equipment are in compliance with the essential requirements and other relevant provisions of Directive 2014/53/EU.
• In accordance with Article 10(2) and Article 10(10), this product is allowed to be used in all EU member states.
• For more information of DoC, Please dick this web link: https://www.godox.com/eu-declaration-of-conformity
• The device complies with RF specifications when the device used at 0mm from your body.

Marking Information

Warranty

Dear customers, as this warranty card is an important certificate to apply for our maintenance service, please fill in the following form in coordination with the seller and safe-keep it. Thank you!

Address
Seller Information| Name
Contact Number
Address
Date of Sale
Note

Applicable Products
The document applies to the products listed on the Product Maintenance Information (see below for further information). Other products or accessories (e.g. promotional items. Giveaways and additional accessories attached. etc.) are not included in this warranty scope.

Warranty Period
The warranty period of products and accessories is implemented according to the relevant Product Maintenance Information. The warranty period is calculated from the day(purchase
date) when the product is bought for the first time. And the purchase date is considered as the date registered on the warranty card when buying the product.

How to Get the Maintenance Service

• If maintenance service is needed, you can directly contact the product distributor or authorized service institutions. You can also contact the Godox after-sale service call and we will offer you service.
• When applying for maintenance service, you should provide valid warranty card.
• If you cannot provide valid warranty card, we may offer you maintenance service once confirmed that the product or accessory is involved in the maintenance scope, but that shall not be considered as our obligation.

inapplicable Cases

• The guarantee and service offered by this document are not applicable in the following cases:

1. The product or accessory has expired its warranty period;

2. Breakage or damage caused by inappropriate usage, maintenance or preservation, such as improper packing, Improper usage, improper pugging in/out external equipment, falling off or squeezing by external force, contacting or exposing to the improper temperature, solvent, acid, base, flooding and damp environments, etc.

3. Breakage or damage caused by non-authorized institution or staff in the process of installation, maintenance, alternation, addition and
   detachment;

4. The original Identifying information of product or accessory Is modified, alternated, or removed

5. No valid warranty card;@. Breakage or damage caused by using
   illegally authorized, nonstandard or non-publics released software

6. Breakage or damage caused by force majeure or accident

7. Breakage or damage that could not be attributed to the product itself. Once met these situations above, you should seek solutions from the related responsible parties and Godox assumes no responsibility. The damage caused by parts, accessories and software that beyond the warranty period or scope is not included in our maintenance scope. The normal discoloration. abrasion and consumption are not the breakage within the maintenance scope.

Maintenance and Service Support Information
The warranty period and service types of products are implemented according to the following Product Maintenance Information:

Product Name Maintenance Type Period(month)| Warranty Service Type
---|---
Parts| Product Main Body| 12| Customer sends the product to designated site
Battery| | Customer sends the product to designated site
Charger. Electrical Parts etc.| 12| Customer sends the product to designated site
Other Items| Battery Case. Windscreen Foam, Wind Cap, Locking Device Lanyard. Tie, Velcro Tape, Chp.Bag,Packageetc| No| Without warranty

Godox After-sale Service Call 0755-29609320-8062

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>