LOVENS 10206803 Explorer Premium Rain Cover User Manual

: June 13, 2024
: LOVENS

Table of Contents

Warranty
Requirements
Instructions
Documents / Resources

LOVENS EXPLORER PREMIUM RAIN COVER.
USER MANUAL
Art.nr.: 10206803 LOVENS 10206803 Explorer Premium Rain
Cover

PLEASE NOTE
Always check the website for the most recent version of the manual.
Visit the service page at www.lovensbikes.com.

Warranty

Read the user manual of the Lovens Explorer for the general terms and conditions and safety instructions for use of the Lovens Explorer.
Lovens offers a two-year warranty against manufacturing and/or production defects.
The warranty requires the use of only original parts. If other parts are used, Lovens cannot be held liable for any damage.
Ensure that the rain cover is properly fastened as described in the user manual. Incorrect attachment may cause damage to the rain cover and/or hazardous situations.
Modifying the rain cover yourself is not permitted. If this is done, functionality can change and the warranty will be voided.
The warranty is valid from the moment at which the dealer sells the rain cover to the consumer. This means it is important to keep your proof of purchase in a safe place.
This rain cover is only suitable for the Lovens Explorer from Lovens.

Requirements

2.1 Own parts

Certain tools are required to install the rain cover. Ensure that you have the following tools:
Open-ended wrench 9 mm
Hex wrench 3
Hex wrench 4

2.2 Product parts

Figure 1 – Lovens Explorer rain cover main parts.

Rain cover
Set of rods (2x)
M4x20 bolt (2x)
M6x20 bolt (2x)
Adapter (2x)
Bolt with press connector (2x)
Loop connector (2x)
Countersunk screw (2x)
Cap for loop connector (2x)
M6 washer (2x)
M4 washer (2x)

Instructions

3.1 Installation instructions

Place the fabric part of the rain cover ❶ on a clean surface to avoid scratching the fabric and windows.
Place the rod assemblies ❷ in the opening provided for this purpose in the fabric, with the straight rods first.
Attach the two adapters ❻ to the bike. Use the M4x20 bolt ❹ and M4 washer ⓬ on the underside and the M6x20 bolt ❺ and M6 washer ⓫ on the side.
Screw the press connectors ❼ into the front of the Lovens Explorer. Fix these in place using a 9 mm open-ended wrench.
Insert the countersunk screw ❾ into the loop connector ❽.
Turn the screw with loop connectors into the rear of the Lovens Explorer.
Close the loop connectors with the ⓬caps. WARNING
• If you do not use the rain cover, it is important to remove the adapters from the frame. This ensures that children’s fingers cannot get trapped in the adapter.
Take the fabric with the rod assemblies and place this in the Lovens Explorer adapters.
Attach the press connectors on the front of the bike to the fixing points in PLEASE NOTE
• Ensure that the press connectors on the front are properly closed. If the press connectors are not attached or closed properly, hazardous situations may arise.
Attach the rubber band at the rear to the loop connector to close the rain cover.

3.2 Instructions for use

When placing your children in or removing them from the bike, you can detach one of the loops at the rear.
WARNING
• Check that the brake levers on the handlebars do not touch the rain cover before use. If this is the case, adjust the position of the handlebars.
Incorrect adjustment can lead to hazardous situations. Consult the Lovens Explorer user manual to find out how to adjust the handlebars.

PLEASE NOTE

To prevent damage or sagging, do not place objects on the rain cover.
The rain cover does not protect against accidents. This means it is important to take safety precautions as specified in the Lovens Explorer user manual.
Ensure that the rain cover is removed from the Lovens Explorer before transporting the Lovens Explorer.
Do not touch the fabric with greasy hands.
Take care in extreme weather conditions. Do not use the rain cover in winds exceeding wind force 6. This may adversely affect the safety of you and the children.
To reduce the risk of theft of the rain cover during temporary parking, it is possible to place a chain lock around the protection tube and the canvas:
1. Partially open the front zipper of one of the side windows.
2. Thread a chain lock through the side window and through the notch in the bin.
3. ttach the chain lock to a post, wall or floor anchor to prevent theft of your Lovens and rain hood.

3.2.1 Opening side windows

Open both the front and rear zipper.
Roll up the side window to the top.
Use both the front and rear rubber bands to secure the rolled-up window. These rubber bands are located on the inside of the roof. The attachment points for the rubber bands are located on the top of the roof.

3.2.2 The rear panel

The rear panel consists of two halves of mesh that can be connected by a magnetic fastener.
If necessary, use the additional Velcro closure at the top for an extra strong attachment.
At the bottom of the back panel there are are two storage compartments. Open the flaps above the compartments to use them.

CAUTION

Do not leave valuables in the storage compartments.
Be careful when opening or dismantling the rain canopy that nothing falls out of the storage compartments.

3.2.3 The sunscreen

The sunscreen consists of a stretchy fabric with three hooks.
The sunscreen can be attached to the inside of the roof in two different ways:
1. Use the rear attachment points to shield the entire top of the roof from the sun.
2. Use the front attachment points to shield the front of the canopy from the sun. This type of mounting is recommended when using a Maxi-Cosi

LOVENS 10206803 Explorer Premium Rain Cover - Figure17

3.3 After use
3.3.1 Cleaning

Clean the rain cover with a damp cloth and/or a soft brush. Do not use cleaning products containing soap or chemicals.
Ensure that the reflective strip on the rain cover is visible at all times. Clean this with a damp cloth if necessary.

3.3.2 Disassembly

Open the press connectors at the front and rear.
Detach the Velcro strip from the frame.
Remove the rain cover and rod assembly from the Livens Explorer.
Place the rain cover on a clean surface.
Remove the rods from the fabric part of the rain cover.
Fold both flaps inward and carefully roll up the fabric.
Remove the angled rods from the adapters and place these in the bag with the other rods and fabric.
Unscrew the adapters from the bike. Place the adapters and bolts in the bag provided for this purpose.

3.3.3 Storage

When storing the rain cover, ensure that the windows of the rain cover are not folded more than necessary, as this may damage the windows.
Store the dry rain cover in a dry place.
To prevent damage or sagging, do not place heavy objects on the rain cover.
To prevent accidents, we advise regularly checking the rain cover for wear.

3.3.4 Maintenance

If the rubber bands at the back are worn out or broken, it is possible to replace them. To do this, open the Velcro strip and remove the elastic. Insert the new elastic and close the Velcro strip again.

Lovens is a trading name of Optima Mobility Holding BV. All images in this brochure are the property of Optima Mobility Holding BV. We reserve the right to modify the models and versions. Colour differences may exist between the images and the actual colours. No rights may be derived from this brochure. No part of this brochure may be copied or used without the explicit permission of Optima Mobility Holding BV. Beverwijk, the Netherlands.

Contact details
Lovens – Optima Cycles Trading B.V.
Bevel and 2
1948 RA Beverwijk
info@lovensbikes.com Quick Start Guide
DEEPWAVE

Documents / Resources

| LOVENS 10206803 Explorer Premium Rain Cover [pdf] User Manual
10206803, 10206803 Explorer Premium Rain Cover, Explorer Premium Rain Cover, Premium Rain Cover, Rain Cover, Cover
---|---