Deko Light 862161 Power Supply Unit User Manual

June 2, 2024
DEKO LIGHT

Deko Light 862161 Power Supply Unit

Deko Light 862161 Power Supply Unit

Dear customer,
thank you for deciding to purchase our product. The product fulfils the requirements of effective European and national guidelines. To maintain the condition of the product and to ensure safe operation, you – as the user – must observe the product notes and the operation manual! They contain important information for the start-up and handling. It is important, therefore, that these documents are archived carefully for referring to information at a later stage.

Safety Instructions

  • We are not responsible for any property damage or personal injury caused by failure to observe these product notes and manual, improper handling or unauthorised modifications.
  • It can only be installed by a qualified electrician.
  • Make sure that the item has not been damaged during transport before putting the light into operation. It may not be operated if there are any damages to electrical parts.
  • It may only be operated once removed from the packaging.
  • The type plate must not be removed.
  • The connection lines in the building must be disconnected before installation and secured against being switched back on. For this, trip the corresponding fuse switch in the building installation.
  • Make sure the electrical specifications for the connection lines correspond with the specifications given on the nameplate of this product.
  • We recommend that you protect the product with a residual-current-operated protective device. Follow all installation regulations applicable at your location.
  • Make sure that the cables and plugs are not subject to tension or torsional forces and do not bend the cables.
  • Protect all cables and insulation against possible damages.
  • Output lines should be laid separately and spaced apart from other lines. The power supply cables and the lamp feeders must not cross each other.
  • Do not allow the product to come into contact with extreme heat or naked flames.
  • Use the supplied fastening material only when it is suited for the installation background.
  • The product must not be covered with objects (decorations) or thermally insulating coverings /similar materials.
  • Before disposal of the packaging material make sure that all components are removed.
  • Keep packaging material away from the reach of children and pets. The packaging contains small parts that may be swallowed by children.

Proper Use
This product is only intended for lighting purposes and may only be operated on normal or non-flammable surfaces. Use the product only in protected and dry interior rooms.

Care

  • Repairs may only be carried out by a qualified electrician.
  • Disconnect the entire product from the mains first and allow it to cool down before cleaning or maintaining.
  • Use a dry or slightly moistened cloth for cleaning.
  • Never use any chemicals, flammable cleaning agents or abrasives. These may cause damage to the surface coating and/or the insulators.

Faulty Function

  • Light switched on at the switch?

  • Transformer mounted and connected properly?
    If available; remote control intact? Check the batteries. Check the connected lines.

  • Lamp defective?

Storage and Disposal
Used electronic devices must be brought back to public collection points and must not be disposed of as household waste. Storage in a dry and clean environment. Do not strain the product mechanically during storage.

Purchased parts package

  • Power supply unit, BASIC, DIM, CV, 200AD-24V
  • 1x User manual

Technical data

  • Power supply: 220-240V AC/50-60Hz
  • Output voltage: 24V DC
  • Output power: 200,00 W
  • Output current: 8,3 A max.
  • Protection class: IP20
  • Signal: DALI-Bus nach IEC 62386 / 1-10V / Touch Dim
  • Channel: 2
  • Working temperature: -20°- +50°C
  • Dimensions (LxWxH): 310 x 60 x 45 mm
  • Weight: 860 g

Product Features

  • Support 1-10V
  • Meet DALI Protocol IEC62386
  • Support Touch DIM function
  • adjustable resistance

Interfaces and Operations

Attention:

  • Remark : DALI and Touch DIM functions cannot be used simultaneously, which can be controlled respectively by using DALI controllers or the equipments with Touch DIM function.

Dali wiring

Deko Light 862161 Power Supply Unit 1

Article No.: 862161

Deko Light 862161 Power Supply Unit 2

Touch Dim wiring

Deko Light 862161 Power Supply Unit 3

Touch Dimmer Funktion

  1. For the push function, only use buttons with a normally open function (e.g. 1-pole). Maximum cable length between devices: 20 meters.
  2. To switch the DALI control input of the power supply to the push function, press the already connected push button for 10s for the first time.
  3. Briefly press the button (<0.5s) to switch the power supply on or off.
  4. Long press the button (>0.5s) to dim the brightness. The dimming direction (light-dark / dark-light) changes each time the button is pressed. Dimming range 1%-100%.
  5. If you press the button twice within (<0.3 s), the power supply is set to maximum brightness. Thanks to the integrated memory function, the last brightness setting is restored when switching on. The function is only supported if the power supply unit is continuously supplied with power.

Touch Dim Diagram

Deko Light 862161 Power Supply Unit 4

Documents / Resources

| Deko Light 862161 Power Supply Unit [pdf] User Manual
862161 Power Supply Unit, 862161, Power Supply Unit, Supply Unit, Unit
---|---

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals