Shuttle X50V9 53R-X50V93-2001 X Vision Black At Reichelt Elektronik User Guide

**X50V9
Quick Guide

More information on this product can be found at: http://bit.ly/X50V9
**

Product Overview

01. Microphone
02. Webcam
03. LCD Display (Single Touch)
04. Hard Disk Drive LED
05. Power LED
06. Stereo Speakers
07. Stylus| 08. Power Button
09. Hole for hidden Power Button
10. USB 3.2 Gen 1 Ports
11. Clear CMOS button
12. Stand / Handle
13. Perforation for optional WLAN
14. Kensington® Lock Hole | 15. COM Ports (Optional) COM
16. VGA Port VGA
17. Power jack
18. HDMI Port
19. LAN Port
20. USB 3.2 Gen 2 Ports
21. Headphones / Line-out Jack
22. Microphone Jack
---|---|---

Hardware Installation

A. Begin Installation
For safety reasons, please ensure that the power cord is disconnected before opening the case.

• Follow the steps (a-b-c-d-e-f) to remove the stand and back cover.
• Follow the steps (f (Push)-d-c-b-a) to replace the back cover and stand.

B. Memory Module Installation

This motherboard does only support 1.1 V DDR5 SO-DIMM memory modules.

1. Locate the SO-DIMM and paste the thermal pad (50152.25 mm) on the motherboard, which can effectively reduce its temperature.

2. Install the 1st memory module into the DIMMA1 slot.

3. Gently insert the module into the slot in a 45-degree angle.

4. Align the notch of the memory module with the one of the relevant memory slot.

5. Carefully push down the memory module until it snaps into the locking mechanism and put the mylar back in place.

6. Install the 2nd memory module into the DIMMB1 slot (proceed with steps B3 to B5) and paste the thermal pad, as shown.

C. HDD or SSD Installation

1. Unscrew four screws of the bracket and remove it.

2. Mount the HDD or SSD into the bracket with four screws.
   

3. Connect the Serial ATA and power cable to the HDD or SSD.

4. Install the HDD or SSD & bracket in the chassis and tighten the HDD or SSD & bracket with four screws.
   

D. M.2 Device Installation

Notice for M.2 slots:
When CN5 is occupied by NVME device,
CN6 only support SATA interface.

X50V9 only support one NVME device.

1. Locate the M.2 key slots on the motherboard.
   • M.2 2280 M key slot

2. Install the M.2 device into the M.2 slot and secure with the screw.

Pasting a thermal pad on the M.2 SSD can effectively reduce its temperature.

• Follow the steps (1~3) below to connect the AC adapter to the “DC-IN jack”.
Press the “Power Button” to turn on the system.

• Placing on a desk

  • To place the machine on a desk and to carry it, do the following:
    1. Place the X50V9 on a flat surface such as a table.
    2. Pull the stand upwards to an angle of 30°.
    3. To carry or move your X50V9, fully extend the angle to 180°.
    

• Points Calibration (Installation from CD-ROM)

• Run the screen calibration program and perform a 4 points on-screen calibration.
  Click Start / All Programs / eGalax Touch / Configure Utility
  Select [Tools] tab and click [4 Points Calibration]

• Touch and hold the center of the target.
  Repeat on four corners and the screen will adjust automatically.

• When the 4 points calibration is completed, press “OK” to continue.

How to use the Touch Panel
• Experience the ease of managing your digital life with a few touches by using the stylus.
The touch of your finger replaces the mouse and this is all you need to interact with the X50V9.

• Touch = left-click on the mouse
• Touch and hold = right-click on the mouse

VESA mounting it to the wall
• If you are mounting your X50V9 to a wall, remove the cover on the back of the X50V9 first.
Unscrew four screws of the stand mount and remove the stand.
The VESA standard lets users mount it on to walls easily.
Please refer to the user guide of the wall/arm mount kit you bought separately to install it.

The X50V9 can be mounted to a wall using a VESA compatible 75 x 75 mm or 100 x 100 mm wall/arm bracket.

Safety Information

Incorrectly replacing the battery may damage this computer. Replace only with the same or equivalent as recommended by Shuttle. Dispose of used batteries in accordance with the laws of your country.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
This device meets the requirements for the EU conformity in accordance to the currently valid EU directives.

• The equipment was evaluated for use in a maximum air ambient temperature of 40 ºC.

THIS PRODUCT CONTAINS A BUTTON BATTERY
If swallowed, a lithium button battery can cause severe or fatal injuries within 2 hours.
Keep batteries out of reach of children.
If you think batteries may have been swallowed or placed inside any part of the body, seek immediate medical attention.
All bundled parts, power cord included, shall not be used without this product.

Hardware Installation

A. Begin Installation
For safety reasons, please ensure that the power cord is disconnected before opening the case.

• Follow the steps (a-b-c-d-e-f) to remove the stand and back cover.
• Follow the steps (f (Push)-d-c-b-a) to replace the back cover and stand.
  

B. Memory Module Installation
This motherboard does only support 1.1 V DDR5 SO-DIMM memory modules.

1. Locate the SO-DIMM and paste the thermal pad (50152.25 mm) on the motherboard, which can effectively reduce its temperature.
2. Install the 1st memory module into the DIMMA1 slot.
3. Align the notch of the memory module with the one of the relevant memory slot.
4. Gently insert the module into the slot in a 45-degree angle.
5. Carefully push down the memory module until it snaps into the locking mechanism and put the mylar back in place.
6. Install the 2nd memory module into the DIMMB1 slot (proceed with steps B3 to B5) and paste the thermal pad, as shown.

C. HDD or SSD Installation

1. Unscrew four screws of the bracket and remove it.
2. Mount the HDD or SSD into the bracket with four screws.
3. Connect the Serial ATA and power cable to the HDD or SSD.
4. Install the HDD or SSD & bracket in the chassis and tighten the HDD or SSD & bracket with four screws.

D. M.2 Device Installation

• Notice for M.2 slots: When CN5 is occupied by NVME device, CN6 only support SATA interface.
X50V9 only support one NVME device.

1. Locate the M.2 key slots on the motherboard.
2. Install the M.2 device into the M.2 slot and secure with the screw.

Pasting a thermal pad on the M.2 SSD can effectively reduce its temperature.

E. Complete

1. Replace the back cover.
2. Replace the cover, complete.

• Powering on the system

Follow the steps (1~3) below to connect the AC adapter to the “DC-IN jack”.
Press the “Power Button” to turn on the system.

• Placing on a desk

To place the machine on a desk and to carry it, do the following:

1. Place the X50V9 on a flat surface such as a table.
2. Pull the stand upwards to an angle of 30°.
3. To carry or move your X50V9, fully extend the angle to 180°.

• 4 Points Calibration (Installation from CD-ROM)

• Run the screen calibration program and perform a 4 points on-screen calibration.
  Click Start / All Programs / eGalax Touch / Configure Utility
  Select [Tools] tab and click [4 Points Calibration]

• Touch and hold the center of the target. Repeat on four corners and the screen will adjust automatically.

• When the 4 points calibration is completed, press “OK” to continue.

• How to use the Touch Panel

• Experience the ease of managing your digital life with a few touches by using the stylus. The touch of your finger replaces the mouse and this is all you need to interact with the X50V9.
  • Touch = left-click on the mouse
  • Touch and hold = right-click on the mouse

Cleaning the screen: Follow these guidelines for cleaning the outside and handling the screen of the computer.
Turn off the system and disconnect all cables. Use a cleaning cloth which is soft, lint-free and a little damp to gently wipe the screen surface. Do not spray liquids directly onto the device.

• VESA mounting it to the wall

If you are mounting your X50V9 to a wall, remove the cover from the back of the X50V9 first. Unscrew four screws of the stand mount and remove the stand. The VESA standard makes it easy to mount the X50V9 on to walls.
Please refer to the user guide of the wall/arm mount kit you bought separately how to install it.

The X50V9 can be mounted to a wall using a VESA compatible 75 x 75mm or 100 x 100mm wall/arm bracket.

The product’s colour and specifications may vary from the actually shipped product.

Motherboard Illustration

01. Power Button
02. Hole for Hidden Power Button
03. M.2 2280 M key slot (CN5) (for PCIE or WWN04/PCIe Gen4x4)
04. M.2 2230 E Key Slot
05. M.2 2280 M key slot (CN6)
06. Intel® Raptor lake-U Series processor
07. SATA 3.0 6Gb/s connector
08. DDR5 SO-DIMM Slots| 09. USB 3.2 Gen 1 Ports
10. Clear CMOS button
11. MIC-in
12. Headphones
13. USB 3.2 Gen 2 Ports
14. LAN Port
15. HDMI Port
16. Power Jack (DC IN)
---|---

Jumper Settings

J1 COM 1 & COM 2 power switch

JP3

Pin| Signal Name| Pin| Signal Name
1| #NAME?| 6| +5P0VS0
2| COM-XRI1| 7| COM1_PWR
3| #NAME?| 8| COM2PWR
4| COM-XRI2| 9| +12P0V_S0
5| +5P0V_S0| 10| +12P0V_S0

J2 J3 COM Port

JP2   COM1

Pin| Signal Name| Pin| Signal Name
1| COM_DCD1P_485TX-| 6| DSR1P
2| COM_RX1P_485TX+| 7| RTS1P
3| COM_TXD1P_422RX-| 8| CTS1P
4| COM_DTR1P422RX+| 9| COM-XRI1
5| GND| 10| NULL

JP3   COM2

Pin| Signal Name| Pin| Signal Name
1| DCD2P| 6| DSR2P
2| RX2P| 7| RTS2P
3| TXD2P| 8| CTS2P
4| DTR2P| 9| COM_-XRI2
5| GND| 10| NULL

References

• Shuttle Global - X50V9 SERIES

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>