X-SENSE WS01 Water Leak Sensor User Manual
- June 3, 2024
- X-SENSE
Table of Contents
X-SENSE WS01 Water Leak Sensor
This user manual contains important information about the operation of your water leak sensor. To ensure proper use and trouble-free operation, please read this manual carefully and store it in a safe place for future reference.
Introduction
This water leak sensor sounds an alarm whenever it comes into contact with water. It can be placed near common household water sources like a dishwasher, hot water heater, or washing machine. With professional monitoring, you will be notified if your home is in danger.
Produd Overview
Package Contents
Operating Your Device
Activating the Device
Press and hold the Activate button for 3 seconds. When the red LED flashes
once and the alarm sounds one beep, then the product is activated and enters
the normal working status.
Testing the Device
After the device is activated, you must test the device to ensure it is
operating normally. Press the Test button at the bottom of the device. The
alarm will deliver 3 beeps paired with the red LED flashing. The sound will
automatically stop after the test is completed.
Water Leak Detection
This water leak sensor is used to detect water leaks and floods. Once a water
leak occurs, the device will sound an alarm continuously paired with a
flashing red LED. If the user takes no action at this time, the device will
continue to sound an alarm until the battery runs out.
SIiencing the Device
When the device is triggered, press the Silence button to mute the alarm, which will last for 10 seconds. After 10 seconds, the device will continue to sound an alarm. To disable the alarm, you must completely clean and dry the surface of the device.
Installing Your Device
Installation Location
You can use the device near places where water leaks are likely to occur such as near water pipes, basement sump pumps, dishwashers, washing machines, toilets, water heaters, window wells, etc.
Installation Method
This sensor can simply be placed on a fiat surface.
Note
- Do not place the device upright, othe,wise no alarm will be triggered.
- Do not place the device on uneven surfaces as this may cause false alarms.
Battery Replacement
When the battery is low, the red LED will flash once every 60 seconds paired
with one beep to remind the user to replace the batteries. To replace the
batteries, remove all screws, take out the used batteries and replace with two
new AAA batteries. Then, reinstall the screws and press and hold the Activate
button for 3 seconds to activate the device. Then test the device once
again.
Note: After replacing the battery, you need to align the positioning
points of the upper and lower cases to close the cover and then screw the
device closed.
WARNiNG
- Keep the device operating at a temperature between 32-122°F (0-50°O and humidity below 90% RH.
- Do not disassemble the device by force. Otherwise, the device may become damaged.
Technical Specifications
| Power Supp ly | Replaceable 2 x 1.5 V AM batteres |
|---|---|
| Operating Life | 5 years |
| Battery Life | 3 years |
| Sensor Type | Sensor probe |
| Operating Temperature | 32-122°F (0-50°0 |
| Operating Relative Humidity | ,; 90% RH (non-condensing) |
| Alarm Volume | 105 dB |
| Silence Duration | 10 seconds |
| Waterproof Rating | IP66 |
Troubleshooting
|
---|---
The device does The device is| Check whether the device
is
not work.It is| not activated.| activated. The device needs to be
not triggered| | activated before it is used for the
when there is a| | first time. Otherwise, the device
water leak.| | will not be triggered (refer to
| | ·Activating the Device· section).
| | Upon activation, press the Test
| | button to make sure it is
| | operating properly.
| The battery is| Please check whether the battery
| low.| power is sufficient. When the
| | battery is low, the red LED will
| | flash once every 60 seconds
| | paired with one beep. Please
| | replace the battery immediately.
The alarm sound is low.| Water entered the alarm.| The device
is waterproof and its performance will not be affected if water gets
inside. Please take the device in your hand and shake it a few times to
remove the water from the alarm opening until the alarm sound returns to
normal. Then put the device back.
---|---|---
Environmental Protection
Waste electrical products should not be disposed of with household waste. Please recycle where facilities are available. Please check with your local authorities or retailers for recycling advice.
Manufacturer and Service Information
X-Sense Innovations Co., Ltd.
Address : 84-503, Kexing Science Park 15 Keyuan Road, Shenzhen, 518057,
CHINA
Email : support@x-sense.com 
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>