Holmes 32510150 18 Inch Digital Stand Fan Instruction Manual
- June 13, 2024
- Holmes
Table of Contents
Holmes 32510150 18 Inch Digital Stand Fan Instruction Manual
PLEASE READ AND SAVE THESE
IMPORTANT SAFETY INSTRUCTIONS
When using electrical appliances, basic safety precautions should always be taken including the following:
-
Read all instructions before using this appliance.
-
Use fan only for purposes described in the instruction
manual. -
This fan is not intended for continuous operation or
equivalent. -
To protect against electrical shock do not immerse
unit, plug or cord in water or spray with liquids and
plug the appliance directly into a 120V AC electrical
outlet. -
Close supervision is necessary when any appliance is
used near children. -
Not intended for use by children.
-
Unplug from outlet when not in use, when moving fan from one location to another, before putting on or taking off parts and before cleaning.
-
Avoid contact with moving parts.
-
Do not operate in the presence of explosive and/or flammable fumes.
-
To avoid fire hazard, never place the cord under rugs or any parts near an open flame, cooking or other heating appliance.
-
Do not operate any appliance with a damaged cord or plug, after the appliance malfunctions, or has been dropped/damaged in any manner. Discard fan or contact customer service.
-
Do not run cord under carpeting. Do not cover cord with throw rugs, runner, or similar coverings. Do not route cord under furniture or appliances. Arrange cord away from traffic area and where it will not be tripped over.
-
The use of attachments not recommended or sold by the appliance manufacturer may cause hazards.
-
Do not let the cord hang over the edge of a table, counter or come in contact with hot surfaces or leave exposed to high traffic areas.
-
Do not use outdoors.
-
To disconnect, grip plug and pull from wall outlet.
Never yank on cord. -
Always use on a dry, level surface.
-
Do not operate fan until fully assembled with all parts properly in place.
-
This product is intended for household use only and not for commercial or industrial applications.
-
WARNING: To reduce the risk of fire or electric shock, do not use this fan with any solid-state speed control device.
-
WARNING:To Reduce The Risk Of Fire, Electric Shock Or Injury To Persons, Do Not Use Replacement Parts That Have Not Been Recommended By The Manufacturer (e.g. Parts Made At Home Using A 3D Printer).
-
For models with overload protection (fuse). A blown fuse indicates an overload or short-circuit situation.
If the fuse blows, unplug the product from the outlet.
Replace the fuse as per the user servicing instructions (follow product marking for proper fuse rating) and check the product. If the replacement fuse blows, a short circuit may be present and the product should be discarded or contact customer service.
PLEASE READ AND SAVE THESE IMPORTANT SAFETY INSTRUCTIONS
THIS APPLIANCE HAS A POLARIZED PLUG (one blade is wider than the other).
To reduce the risk of electric shock, this plug is intended to fit in a
polarized outlet only one way. If the plug does not fit fully in the outlet,
reverse the plug. If it still does not fit, contact a qualified electrician to
install the proper outlet.
DO NOT ATTEMPT TO MODIFY THIS PLUG OR DEFEAT THIS SAFETY FEATURE IN ANY WAY.
PARTS AND ASSEMBLY
ASSEMBLY INSTRUCTIONS (SEE FIGURE 1)
NOTE: MAKE SURE YOU REMOVE ALL CONTENTS OF THE PACKAGE. PLEASE CHECK PACKAGING
MATERIALS FOR PARTS THAT COULD BE REQUIRED TO OPERATE THIS FAN.
Tools required: Phillips head screw driver (not included)
Estimated assembly time: 5–10 minutes
- Remove L-shaped Locking Screw (T) and Washer (S) from the Outer Pole (P) . Place Outer Pole (P) overtop of the base. Insert the threaded end of the L-shaped locking screw (T) into the hole of the Washer (S) and through the base.Turn the L-shaped locking screw (T) clockwise to securely attach the pole to the base.
- Loosen Fan Post Screw (M) and slide Motor Housing (K) over top of Extension Pole (N). Tighten Fan Post Screw (M).
- Line up the 2 holes of the Rear Grill (H) with the posts on the Motor Housing (K) assembly. When properly aligned, the handle (I) of the rear grill should be in the 12 o’clock position.
- Secure Rear Grill (H) to Motor Housing (K) with Rear Grill Mounting Nut (G). Turn clockwise to tighten.
- Slide Blade (F) over Motor Shaft (J).
- Secure fan blade to motor shaft with the Blade Cap (E). Turn counter-clockwise to tighten.
- Open the expandable Grill Clips (D) located around the perimeter of the Front Grill (B).
- Remove the nut from the Grill Locking Screw (C) and align the hole located at the bottom of the Rear Grill (H) with the hole at the bottom of the Front Grill (B).
- Close all the Grill Clips (D) around the perimeter of the grill.
- Insert the screw into the hole at the bottom of the grill. Secure in place by tightening the nut over the back of the screw. (Use Phillips head screw driver).
FEATURES – OPERATIONS
OPERATING INSTRUCTIONS
-
Set fan base on a dry, level, stable surface.
-
Plug cord into any standard 120 volt AC outlet.
-
To turn the fan on, press the POWER button located on the control panel or remote control. The fan will start running in the lowest setting “L” ( LOW ).
-
Press the speed button to cycle through the below 3 speed settings in sequence. The corresponding indicator light will illuminate to confirm the selection: L-Low M-Medium H-High
-
To turn the oscillation on and off, press the oscillation button located on the control panel or remote control.
-
To set your fan to automatically shut off, press the timer button located on the control panel or the remote control. When set, the fan will run and automatically shut off after the set duration of time (0.5-7.5 hours) has expired.
-
To activate BREEZE mode, press the MODE button (E).
The fan will cycle through alternating speeds with brief pauses to simulate a natural outdoor breeze.
To activate SLEEP mode, press the MODE button again.
This function slows the BREEZE setting by one level every ten minutes until it reaches LOW. -
To silence setting confirmation beeps, press the MUTE button (F) located on the remote control. To reactivate setting confirmation beeps, press the MUTE button (F) again
-
To turn the fan off press the power button located on the control panel or remote control.
TILT ADJUSTMENT
Gently move the fan head up or down manually to the desired angle.
HEIGHT ADJUSTMENT
- Turn the Height Adjustment Collar (O) counterclockwise to loosen pole.
- Adjust the Extension Pole (N) to the desired height, and firmly tighten the height adjustment collar in a clockwise direction.
REMOTE CONTROL: (SEE FIGURE 3)
NOTE: PLEASE REMOVE THE PROTECTIVE PLASTIC FROM THE REMOTE CONTROL BATTERY
BEFORE OPERATION.
This unit includes one lithium battery, CR2025/3V
Remove battery before discarding the remote.
Battery Replacement
The cells should be disposed of properly, including keeping them away from
children. Even used cells may cause injury.
- Locate the battery compartment on the bottom back of the remote control handset. Push tab and pull battery tray.
- Remove old battery.
- Place new battery into battery compartment.
- Slide battery compartment into the remote control handset.
NOTES:
- Remove the battery from the equipment when it is not being used for an extended period of time.
- Remove the used battery promptly.
- Do not discard used batteries into household trash containers. Contact your local government for disposal or recycling practices in your area.
OPERATIONS / C L E A N I N G / MAINTENANCE
USER SERVICING INSTRUCTIONS
Follow these instructions to safely and correctly care for this fan.
REPLACEABLE FUSE
If the (2.5 Amp, 125 Volt) replaceable fuse blows, please visit our website at
www.getholmesfans.com for information on how to order a new fuse. Follow the
below instructions to replace the fuse on the plug.
REPLACING THE FUSE
-
Unplug the fan.
Grasp plug and remove from the receptacle or other outlet device.
NOTE: Do not unplug by pulling on cord. -
Open fuse cover, located on the top of the plug, by using your thumb or a flathead screwdriver to slide the cover towards the prongs.
NOTE: Ensure the fuse cover is completely open before attempting to remove fuse. -
Remove fuse carefully by using a small screwdriver to pry it from the compartment at the metal ends of the fuse. (See Figure 2)
-
Place plug on a solid, flat surface. Insert new 2.5 Amp, 125 Volt fuse into fuse compartment. Use a small screwdriver to secure the metal ends of the fuse into the compartment.
CAUTION: Risk of fire. Replace fuse only with 2.5 Amp, 125 Volt fuse. -
Slide fuse cover closed completely.
NOTE: If fuse cover is difficult to close, make sure the fuse is completely secured in place by pressing on metal ends of the fuse.
CAUTION: Risk of fire. Do not replace the attachment plug. It contains a safety device (fuse) that should not be removed. Discard product if the attachment plug is damaged.
FAN CLEANING
- Always unplug the fan before cleaning.
- Do not allow water to drip on or into the fan housing.
- Use only a soft cloth moistened with a mild soap solution.
- Do not use harsh chemicals such as gasoline, thinner or benzene as a cleaner.
FAN BLADE CLEANING
- Remove the front grill by opening the clips located around the perimeter.
- Clean the fan blade, front and rear grills with a soft cloth moistened with a mild soap solution.
- Securely fasten the front grill to the rear grill by closing the clips over the perimeter.
FAN HEAD, BASE AND POLE CLEANING
Using a soft, moist cloth (with or without a mild soap solution), carefully
clean the fan base, pole and head.
Use CAUTION around the housing area. Do not allow the motor or other electrical components to be exposed to water.
FAN STORAGE
This fan can be stored either partially disassembled or assembled.
- Store the fan in a clean, dry location between seasons or when not in use for an extended period of time.
- Keep the fan protected from dirt and dust during storage.
NOTE: This fan can also be used during the cold winter season to circulate warm air throughout your home.
For inquiries regarding recycling and proper disposal of this product, please contact your local waste management facility.
FCC STATEMENT / WARRANTY INFORMATION
FCC STATEMENT
Potential for Radio/Television interference
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions:
(1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference
that may cause undesired operation.
This product has been tested and found to comply with the limits for a Class B
digital device, pursuant to part 15 of the FCC rules.
These limits are designed to provide reasonable protection against harmful
interference in a residential installation.
The product generates, uses, and can radiate radio frequency energy and, if
not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that the
interference will not occur in a particular installation. If the product does
cause harmful interference to radio or television reception, which can be
determined by turning the product on or off, the user is encouraged to try to
correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the product and the receiver.
- Connect the product into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
- Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
The following importer is the responsible party:
Company Name: SEG Products US Corp.
Address: 8 The Green, Suite #6962, Dover, DE 19901
Telephone: 1-959-202-4223
3 YEAR LIMITED WARRANTY
This device has a limited warranty of 3 years from the original date of
purchase against workmanship and defects in material. If under normal use,
your product fails to operate, please contact our customer service department
at info@getholmesfans.com. A refund or
replacement will be provided to you with proof of purchase. Star Elite Inc.
may deny claims of damage caused by misuse or modifications of this product.
Warranty Service
Contact our customer service at www.getholmesfans.com/en/contact-us or
info@getholmesfans.com or
1-866-769-3166 (8:30 am – 5:00 pm EST)
Monday-Friday.
Our team will be happy to assist.
©2023 Sunbeam Products, Inc. All rights reserved.
HOLMES® is a registered trademark of Sunbeam Products, Inc. used under
license.
Distributed by Star Elite Inc., Montreal, Canada H3B 3X9
SEH024-013023
Read More About This Manual & Download PDF:
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>