Holmes HWF0910A 1Touch Twin Window Fan Owner’s Manual
- June 13, 2024
- Holmes
Table of Contents
Holmes HWF0910A 1Touch Twin Window Fan
IMPORTANT SAFETY INSTRUCTIONS
When using electrical appliances, basic safety precautions should always be taken including the following:
- Read all instructions before using this appliance.
- Use fan only for purposes described in the instruction manual.
- To protect against electrical shock do not immerse unit, plug or cord in water or spray with liquids and plug the appliance directly into a 120V AC electrical outlet.
- Close supervision is necessary when any appliance is used by or near children.
- Unplug from outlet when not in use, when moving fan from one location to another, before putting on or taking off parts and before cleaning.
- Avoid contact with moving parts.
- Do not operate in the presence of explosive and/or flammable fumes.
- To avoid fire hazard, NEVER place the cord under rugs or any parts near an open flame, cooking or other heating appliance.
- Do not operate any appliance with a damaged cord or plug after the appliance malfunctions, or has been dropped/damaged in any manner. Discard fan or return to an authorized service facility for examination and/or repair.
- Do not run cord under carpeting. Do not cover cord with throw rugs, runner, or similar coverings. Do not route cord under furniture or appliances. Arrange cord away from traffic area and where it will not be tripped over.
- The use of attachments not recommended or sold by the appliance manufacturer may cause hazards.
- Do not let the cord hang over the edge of a table, counter or come in contact with hot surfaces or leave exposed to high traffic areas.
- Do not use outdoors.
- To disconnect, grip plug and pull from wall outlet. Never yank on cord.
- Always use on a dry, level surface.
- Do not operate fan until fully assembled with all parts properly in place.
- This product is intended for household use ONLY and not for commercial or industrial applications.
- WARNING : To reduce the risk of fire or electric shock, do not use this fan with any solid-state speed control device.
- This product employs overload protection (fuse). A blown fuse indicates an overload or short-circuit situation. If the fuse blows, unplug the product from the outlet. Replace the fuse as per the user servicing instructions (follow product marking for proper fuse rating) and check the product. If the replacement fuse blows, a short circuit may be present and the product should be discarded or returned to an authorized service facility for examination and/or repair. PLEASE READ AND SAVE THESE IMPORTANT SAFETY INSTRUCTIONS.
THIS APPLIANCE HAS A POLARIZED PLUG (one blade is wider than the other). To reduce the risk of electric shock, this plug is intended to fit in a polarized outlet only one way. If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician to install the proper outlet. DO NOT ATTEMPT TO MODIFY THIS PLUG OR DEFEAT THIS SAFETY FEATURE IN ANY WAY
FEATURES – OPERATIONS
INSTALLATION INSTRUCTIONS
NOTE : MAKE SURE YOU REMOVE ALL CONTENTS FROM THE PACKAGE. PLEASE CHECK
PACKAGING MATERIALS FOR PARTS THAT COULD BE REQUIRED TO OPERATE YOUR FAN.
The window fan comes fully assembled and is ready for immediate installation.
This window fan has been designed to fit double-hung windows with minimum
openings of 25 inches (63 cm) wide and 12 inches (30 cm) high.
NOTE : THIS FAN IS DESIGNED AND RECOMMENDED FOR USE WITH A SCREEN IN THE
WINDOW.
For Double-Hung Windows
- Align the Window Fan horizontally in the window with the controls facing you and the Built-In-Extender Panel to the right.
- Set the fan into your window opening (note that in most cases the window screen does not have to be removed or left open).
- If the fan does not fit snugly to the top and bottom of the window casing, attach the included Slider Safe extender panel and pull out the Built-In Extender Panel until the fan sits safely in your window.
- If the fan still does not fit snugly attach the Slider Safe Extender Panel located in the packaging in the original box. Align the slot in the Slider Safe Extender Panel along the tab located on the left side of your Window Fan. Slide the Slider Safe Extender Panel completely down the tab until it is flush on both the top and bottom of the Window Fan.
- To keep the fan in place, carefully close the window so that the bottom edge of the window rests on the flat area on the top of the fan.
For Slider Windows
- Set the Fan vertically in your window opening with the left side of the fan situated on the bottom and the Built-In Extender Panel on top.
- Set the fan into your window opening (note that in most cases the window screen does not have to be removed or left open).
- If the fan does not fit snugly to the top and bottom of the window casing, attach the Slider Safe Extender Panel and adjust the Built-In Extender screen until the fan fits securely in your window.
WARNING : BE SURE FAN IS SECURELY INSTALLED IN YOUR WINDOW AT ALL TIMES. DO NOT LEAN OR PUSH ON THE FAN WHILE IT IS IN THE WINDOW.
OPERATING INSTRUCTIONS
-
Plug the fan into a 120V AC electrical outlet.
-
Set the individual fan motors on either INTAKE, EXHAUST or AIR EXCHANGE using the Left/Right Fan Intake/Exhaust controls (E,D).
NOTE : AIR FLOW DIRECTION CAN BE ALTERED WITHOUT TURNING THE FAN OFF. -
To start the unit and run continuously, push the 1Touch® Fan Button (A) once for the High setting and press the button twice for the Low setting.
-
To stop the unit, press and hold the 1Touch® Control Button (A) for two seconds or you can manually cycle through all of the speeds until all of the LED indicators are no longer lit.
1TOUCH® THERMOSTAT FAN INSTRUCTIONS
Your fan is equipped with the technologically advanced 1Touch® Thermostat Fan. This feature will automatically turn the fan “ON” or “OFF” depending on the preset comfort level. The comfort level ranges between 60° and 80° Fahrenheit. To take advantage of the 1Touch® Fan Thermostat, continue to press the 1Touch® Fan Button (A) until the desired temperature is reached. When room temperature drops below the set temperature, the fan will stop. When the room temperature rises above the set point, the fan will turn on automatically. For example, if you set your thermostat to 75 degrees then your fan will run until the set temperature is reached. Once the temperature rises above the set temperature the fan will automatically turn on again.
CLEANING/MAINTENANCE
Follow these instructions to correctly and safely care for your window fan. Please remember
REPLACEABLE FUSE
If your (5 Amp, 125 Volt) replaceable fuse blows, please visit our website at
www.holmesproducts.com for information on how to order a new fuse. Follow the
below instructions to replace the fuse on the plug.
User Servicing Instructions
-
Unplug your fan. Grasp plug and remove from the receptacle or other outlet device. Do not unplug by pulling on cord.
-
Open fuse cover, located on the top of the plug, by using your thumb or a flathead screwdriver to slide the cover down towards the prongs.
Note : Ensure that fuse cover is completely open before attempting to remove fuse. -
Remove fuse carefully by using a small screwdriver to pry the fuse out of the compartment by the metal ends of the fuse (see Figure 2).
-
Place plug on a solid, flat surface. Insert new 5 Amp, 125 Volt fuse into fuse compartment and use a small screwdriver to secure the metal ends of the fuse into the compartment.
Caution : Risk of fire. Replace fuse only with 5 Amp, 125 Volt fuse. -
Slide fuse cover closed completely. If fuse cover is difficult to close, make sure fuse is secured in place completely by pressing down on metal ends of the fuse.
-
Risk of fire. Do not replace attachment plug. Contains a safety device (fuse) that should not be removed. Discard product if the attachment plug is damaged
FAN CLEANING
- Always unplug the fan before cleaning or disassembling.
- Do not allow water to drip on or into the fan motor housing.
- Do not use gasoline, thinner or benzene as a cleaner.
Fan blade and Front Grill Cleaning
- Make sure the fan is unplugged.
- Using a Phillips head screwdriver, remove the screws located around the perimeter of the rear grill. Carefully separate the front and the rear grills from the end opposite the built in extender. Do not completely detach the grills as this may damage the extender clips. Separate only enough to gain access to the blades with one hand.
- Clean the blades and grills with a soft cloth moistened with a mild soap solution.
- Securely fasten the front and rear grill back together.
FAN STORAGE
For all window fans, and fans that come already assembled.
- It is important to keep it in a safe, dry location.
- We recommend using the original (or appropriately sized) box.
- Please remember to protect the fan from dust or moisture.
WINDOW FAN ACCESSORIES
If you have any questions regarding your product or would like to learn more about other Holmes® products, please visit our website at www.holmesproducts.com. For inquiries regarding recycling and proper disposal of this product, please contact your local waste management facility.
WARRANTY INFORMATION
3 YEAR LIMITED WARRANTY
Sunbeam Products, Inc. doing business as Jarden Consumer Solutions or if in
Canada, Sunbeam Corporation (Canada) Limited doing business as Jarden Consumer
Solutions (collectively “JCS”) warrants that for a period of three years from
the date of purchase, this product will be free from defects in material and
workmanship. JCS, at its option, will repair or replace this product or any
component of the product found to be defective during the warranty period.
Replacement will be made with a new or remanufactured product or component. If
the product is no longer available, replacement may be made with a similar
product of equal or greater value. This is your exclusive warranty. Do NOT
attempt to repair or adjust any electrical or mechanical functions on this
product. Doing so will void this warranty.
This warranty is valid for the original retail purchaser from the date of
initial retail purchase and is not transferable. Keep the original sales
receipt. Proof of purchase is required to obtain warranty performance. JCS
dealers, service centers, or retail stores selling JCS products do not have
the right to alter, modify or any way change the terms and conditions of this
warranty.
This warranty does not cover normal wear of parts or damage resulting from any of the following: negligent use or misuse of the product, use on improper voltage or current, use contrary to the operating instructions, disassembly, repair or alteration by anyone other than JCS or an authorized JCS service center. Further, the warranty does not cover: Acts of God, such as fire, flood, hurricanes and tornadoes.
What are the limits on JCS’s Liability?
JCS shall not be liable for any incidental or consequential damages caused by
the breach of any express, implied or statutory warranty or condition.
Except to the extent prohibited by applicable law, any implied warranty or
condition of merchantability or fitness for a particular purpose is limited in
duration to the duration of the above warranty. JCS disclaims all other
warranties, conditions or representations, express, implied, statutory or
otherwise.
JCS shall not be liable for any damages of any kind resulting from the purchase, use or misuse of, or inability to use the product including incidental, special, consequential or similar damages or loss of profits, or for any breach of contract, fundamental or otherwise, or for any claim brought against purchaser by any other party. Some provinces, states or jurisdictions do not allow the exclusion or limitation of incidental or consequential damages or limitations on how long an implied warranty lasts, so the above limitations or exclusion may not apply to you. This warranty gives you specific legal rights, and you may also have other rights that vary from province to province, state to state or jurisdiction to jurisdiction.
How to Obtain Warranty Service
In the U.S.A.
If you have any questions regarding this warranty or would like to obtain
warranty service, please visit our website at www.holmesproducts.com or direct
your correspondences to ATTN: Holmes, Jarden Consumer Solutions, PO Box 3900,
Peoria IL 61614. Please do not return product to this address. The PO Box
listed can only receive letters or envelopes.
In Canada
If you have any questions regarding this warranty or would like to obtain
warranty service, please visit our website at www.holmesproducts.com or direct
your correspondences to ATTN: Holmes, Jarden Consumer Solutions, PO Box 3900,
Peoria IL 61614. Please do not return product to this address. The PO Box
listed can only receive letters or envelopes.
In the U.S.A., this warranty is offered by Sunbeam Products, Inc. doing
business as Jarden Consumer Solutions located in Jarden Consumer Solutions, PO
Box 3900, Peoria IL 61614. In Canada, this warranty is offered by Sunbeam
Corporation (Canada) Limited doing business as Jarden Consumer Solutions,
located at 20 B Hereford Street, Brampton, Ontario L6Y 0M1. If you have any
other problem or claim in connection with this product, please write our
Consumer Service Department. PLEASE DO NOT RETURN THIS PRODUCT TO ANY OF THESE
ADDRESSES OR TO THE PLACE OF PURCHASE.
© 2015 Sunbeam Products, Inc. doing business as Jarden Consumer Solutions. All Rights Reserved. Distributed by Sunbeam Products, Inc. doing business as Jarden Consumer Solutions, Boca Raton, Florida 33431.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>