LUTEC P6221B LED Floodlight Owner’s Manual
- June 13, 2024
- LUTEC
Table of Contents
LUTEC P6221B LED Floodlight
Product Information
The LED Floodlight is a high-quality lighting fixture designed to provide bright and efficient illumination. It comes with a model number P6221B/P6221W and is available in two color options: black (P6221B) and white (P6221W).
Package Contents
| PART | DESCRIPTION | QUANTITY |
|---|---|---|
| A | Fixture | 1 |
HARDWARE CONTENTS (not shown actual size)
- Fixture (Quantity: 1)
- Screw (Quantity: 2)
- Wire Nut (Quantity: 2)
- Foam Pad (Quantity: 1)
- Rubber Plug (Quantity: 1)
Safety Information
Please read and understand the entire manual before attempting to assemble,
operate, or install the product. Ensure that all parts are present and
undamaged before proceeding with the
installation.
WARNING:
- Consult a qualified electrician if you are not certain about the installation process. Always install wiring connections in accordance with local code, ordinances and the National Electric Code.
- Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
- This light fixture is designed to fit standard junction boxes as defined by the National Electrical Code.
- This light fixture is not dimmable.
This Class B digital apparatus complies with Canadian ICES-005.
NOTICE: This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Product Usage Instructions
Preparation
Before starting the assembly or installation of the lighting fixture, make
sure you have the following tools ready:
- Phillips Screwdriver
- Silicone Caulking Adhesive
- Ladder
Before beginning to assemble or installing lighting fixture, make sure all
parts are present. Compare parts with package contents list and hardware
contents list. If any part is missing or damaged, do not attempt to assemble,
install or operate the product.
Estimated Assembly Time: 20-30 minutes.
Tools Required for Assembly: Phillips Screwdriver, Silicone Caulking
Adhesive, Ladder.
Installation
- Turn OFF power to the work area at the main circuit breaker or fuse box. Do not rely on the wall switch alone to turn off power.
- Remove the screw and the mounting plate pre-assembled in the fixture (A). Set aside the screw for later use.
- Attach the mounting plate to the junction box using the two screws (AA). Then attach the foam pad (CC) to the mounting plate. If installing on the ceiling, follow the same steps.
- Connect the ground wire from the junction box to the ground screw on the mounting plate. Connect the white wire from the junction box to the white wire from the light fixture by twisting a wire nut (BB) onto the bare ends of the wires. Connect the black wire from the junction box to the black wire from the light fixture by twisting a wire nut (BB) onto the bare ends of the wires. Position all the wires inside the fixture junction box.
- Attach the light fixture (A) to the mounting plate using the screw previously removed in step 2. Insert the rubber plug (DD).
- After mounting the fixture, apply silicone caulking compound completely around the perimeter of the cover plate where the back of the cover plate meets the mounting surface. This prevents water from seeping into the junction box.
- Turn ON power to the work area at the main circuit breaker or fuse box.
Care and Maintenance
Regularly inspect the light fixture for any signs of damage or wear. Clean
the fixture as needed using a soft cloth and mild detergent. Avoid using
abrasive cleaners or solvents that may damage the surface. If any issues
arise, refer to the troubleshooting section or consult a certified
electrician.
- Clean surfaces with a mild, non-abrasive cleaner.
Troubleshooting
| Problem | Possible Cause | Corrective Action |
|---|---|---|
| The light will not go on. | 1. No power. |
2. Fixture may be wired incorrectly.
3. Switch may be wired incorrectly. Crossed wires or power wire is grounding
out.| 1. Make sure lamp fixture is plugged in and power is on.
2. Check wiring.
3. Check wiring. Consult a certified electrician.
Fuse blows or circuit trips when fixture is turned on.| 1. No power.
2. Fixture may be wired incorrectly.
3. Switch may be wired incorrectly. Crossed wires or power wire is grounding
out.| 1. Make sure lamp fixture is plugged in and power is on.
2. Check wiring.
3. Check wiring. Consult a certified electrician.
3-Year Limited Warranty
The LED Floodlight comes with a 3-year limited warranty. If the product fails
due to a defect in materials or workmanship within three (3) years from the
date of purchase, it will be replaced with the same or comparable model free
of charge. To claim the warranty, return the product along with proof of date
of purchase. Please note that the warranty is void if damage or defect has
resulted from accident, abuse, misuse, or faulty repair. This warranty
provides specific legal rights, and you may have other rights that vary from
state to state. The warranty does not cover any consequential, special,
incidental, or indirect damages arising out of the use or misuse of the
product.
If this product fails due to a defect in materials or workmanship within three
(3) years from the date of purchase, return it along with proof of date of
purchase and it will be replaced with the same or comparable model free of
charge. This warranty is void if damage or defect has resulted from accident,
abuse, misuse or faulty repair. This warranty gives you specific legal rights
and you may have other rights that vary from state to state.
IN NO EVENT WILL LIABILITY EXTEND TO ANY CONSEQUENTIAL, SPECIAL, INCIDENTAL OR
INDIRECT DAMAGES OF ANY KIND ARISING OUT OF THE USE OR MISUSE OF THIS PRODUCT.
SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR
CONSEQUENTIAL DAMAGES SO THE ABOVE EXCLUSION OR LIMITATION MAY NOT APPLY TO
YOU.
LUTEC USA LLC:
149B Houston Rd Troutman NC 28166
Ningbo UTEC Electric Co.,LTD
CN8, Far East Industry Park, Yuyao, China
www.lutec.com
service@lutec.com
Please call our Customer Service line at
877-714-8669 for assistance Monday –
Friday 9 a.m. to 5 p.m. EST
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>