LedraBrand GGEETT 1111 Eco Track Instruction Manual

LedraBrand GGEETT 1111 Eco Track Instruction Manual

Installation Instructions
Eco

D2234c

INSTALLATION INSTALLATION INSTRUCTIONS INSTRUCTIONS

IMPORTANT SAFETY INSTRUCTIONS

Read All Instructions Before Installation Read All Instructions Before Installation

1. The GLOBAL trac eco system is intended for use with GLOBAL trac eco components and fixtures marked for use with the GLOBAL trac eco system. To reduce the risk of fire and electric shock, do not use other components as part of this system.

2. Track installation is only to be performed by a certified electrician in accordance with the National Electrical Code and all local codes and ordinances.

3. Single-circuit system: The eco GES track system is designed to be supplied by a single 120 volt branch circuit with a maximum capacity of 20 amps.
   Two-circuit system: The eco GET track system is designed to be supplied by a balanced 120/240 volt, three-wire branch circuit with a maximum capacity of 40 amps.

4. Do not use this track system with a power supply cord or convenience receptacle adapter.

5. Do not install any fixtures closer than six inches from combustible materials.

6. Do not install the track in damp or wet locations.

7. Do not install the track with electric power connected. Similarly, disconnect electricity when installing or removing fixtures or components or changing the configuration of the track.

8. Do not attach anything other than UL listed lighting fixtures marked for use with Nordic Aluminum GLOBAL trac eco system only to the track.

IMPORTANT

SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE WHEN ADDING FIXTURES OR CHANGING THE TRACK CONFIGURATION

Mounting the Track

STEP 1

1.1) Locate the polarity line on the face of the track.

1.2) Insert feed connector into end(s) of track, matching polarity lines on connector and track (see Figure 1 below)

1.3) Tighten the locking screw(s) on each leg of the connector until secure (CAUTION: do not over tighten, as damage to the connector may result.)

1.4) Insert GES 41 dead end(s) into all open end(s) of track. Tighten the locking screw on each feed until secure.

STEP 2

2.1) Locate the pre-drilled mounting holes in the back of the track.

2.2) Use toggle bolts or mounting screws to properly secure the track to the ceiling in the correct location. If mounting clips are required, these must be ordered separately.

2.3) Take care to ensure that the track is securely fastened to the ceiling at least once every four feet of length of the track.

STEP 3

3.1) Identify the feed connector that is to be used to provide power to the track.

3.2) Follow the installation instructions included with the appropriate feed connector.

3.3) The track must be wired and installed in accordance with the National Electrical Code and all applicable local codes and ordinances, by a qualified electrician.

STEP 4

Install the lighting fixtures in the track in accordance with the fixture manufacturer’s instructions, taking care to match the polarity line of the track with the polarity line on the fixture adapter.

Cutting the track to length

GLOBAL eco track may be field-cut to length, using the following procedure:

1. Measure the desired length of track.
2. Using a hacksaw or other saw suitable for cutting aluminum, cut the track at with a clean perpendicular cut, ensuring that no damage to conductors results.
3. Remove all loose cutting debris and burrs from ends and inside of track.
4. Install appropriate feed connector or dead end.
5. If cutting the track eliminated a section with a mounting hole, it may be necessary to drill an additional mounting hole to ensure secure fastening to ceiling. If so, please consult the Field Drilling Instructions below.
6. Mount the track following instructions on the opposite page.

Field Drilling Instructions

GLOBAL eco track is supplied with pre-drilled mounting holes (see Figure 2 below.) It may be necessary to drill additional mounting holes in the field if:

• The track has been field-cut to length, using the procedure detailed above, or
• The provided mounting holes do not line up with the mounting surface above the track.

To drill additional mounting holes, use the following procedure:

1. On the inside of the track, mark the correct location for the mounting hole. Note that the track must be securely mounted an intervals no greater than four feet in length.
2. To ensure that the mounting hole does not interfere with a feed connector installed in the end of the track, ensure that the mounting hole is located no closer than 3 inches from the end of the track.
3. Using the drill guide running along the centerline of the inside of the track, drill a 3/16 inch hole through the track.
4. Remove all loose cutting debris and burrs from inside and outside of track.
5. Install appropriate feed connector or dead end.
6. Mount the track following instructions on the opposite page.

Pre-drilled Mounting Hole Locations

GLOBAL eco Feed and Connector Components

The GLOBAL trac eco system includes the following feed and connector components:

Nordic Aluminium, Inc. 1075 Old Norcross Road, Suite A, Lawrenceville, GA 30045, USA

Ph:678-407-7876, Fax: 678-407-7875

In a continuing effort to offer the best product possible we reserve the right to change, without notice, specifications or materials that in our opinion will not alter the function of the product.

Ledra Brands Inc.
www.LedraBrands.com

88 Maxwell Irvine, CA 92618
P 714.259.9959 F 714.259.9969

INSTALLATION INSTRUCTIONS

GES 14CB LIVE MIDDLE FEED WITH CIRCUIT BREAKERS

FOR USE WITH GLOBAL eco SYSTEM ONLY

UPON RECEIPT OF MERCHANDISE: Thoroughly inspect for any freight damage, which should be brought to the attention of the carrier. Compare the catalog description listed with the track or accessory label on the merchandise to be sure you have received the correct merchandise.

GES 14CB consists of:

• Body with circuit breaker(s) and track feeding module(s);
• Canopy
• security torx screws for canoby fastening

GES 14CB may be used only with GES Track

1. Place Feed metal body plate at desired location.

2. Match the polarity lines on the track and connectors as shown in Figures 1 and 2.

3. Insert the connector into the track.

4. Tighten the lock screws on the connector until secure.

5. Install dead end to any end of track. Tighten all dead ends securely to the track.

6. Make proper electrical connections. Connect as follows: As shown in Figure 2

   • Colored wire (Circuit 1) to black wire/L terminal.
   • White wire (Neutral 1) to white wire/N terminal.
   • Ground wire to green wire /ground terminal
     refer to Installation Instruction included with feedable connector for proper electrical connections.

7. Locate canopy over the outlet box and feed connector. To secure, run the retaining screws through the corner holes in the canopy and into the steel body.

IMPORTANT SAFETY INFORMATION

Read all instructions before installation

1. The GLOBAL eco system is intended for use with GLOBAL eco components and fixtures marked for use with the GLOBAL eco system. To reduce the risk of fire and electric shock, do not use other components as part of this system.
2. Track installation is only to be performed by a certified electrician in accordance with the National Electrical Code and all local codes and standards.
3. The GLOBAL eco GES track system is designed to b e supplied by a single 120 volt branch circuit with a maximum capacity of 20 amps. The two circuit GLOBAL eco GET system is to be supplied by a balanced 120/240 volt, three-wire branch circuit with a maximum capacity of 40 amps.
4. Do not use this track with a power supply cord o r convenience receptacle adapter.
5. Do not install any fixtures closer than six inch es from combustible materials.
6. Do not install the track in damp or wet location s.
7. Do not install the track with electric power connected. Similarly, disconnect electricity when installing or removing fixtures or components or changing the configuration of the track.
8. Do not attach anything other than UL listed lighting fixtures marked for use with Nordic Aluminium GLOBAL eco system only to the track.

IMPORTANT

SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE WHEN ADDING FIXTURES OR CHANGING THE TRACK CONFIGURATION

GES 11CB LIVE END FEED WITH CIRCUIT BREAKERS

GES 12CB LIVE END FEED WITH CIRCUIT BREAKERS (Mirror image)

FOR USE WITH GLOBAL eco SYSTEM ONLY

UPON RECEIPT OF MERCHANDISE: Thoroughly inspect for any freight damage, which should be brought to the attention of the carrier. Compare the catalog description listed with the track or accessory label on the merchandise to be sure you have received the correct merchandise.

GES 1 1CB (GES 12CB) consists of:

• Body with circuit breaker(s) and track feeding module(s);
• Canopy
• security torx screws for canoby fastening

GES11 CB and GES 12CB may be used only with GES Track

1. Place Feed metal body plate at desired location.

2. Match the polarity lines on the track and connectors as shown in Figures 1 and 2.

3. Insert the connector into the track.

4. Tighten the lock screws on the connector until secure.

5. Install dead end to any end of track. Tighten all dead ends securelv to the track.

6. Make proper electrical connections. Connect as follows: As shown in Figure 2

   • Colored wire (Circuit 1) to black wire/L terminal.
   • White wire (Neutral 1) to white wire/N terminal.
   • Ground wire to green wire /ground terminal
     refer to Installation Instruction included with feedable connector for proper electrical connections.

7. Locate canopy over the outlet box and feed connector. To secure, run the retaining screws through the corner holes in the canopy and into the steel body.

IMPORTANT SAFETY INFORMATION

Read all instructions before installation

1. The GLOBAL eco system is intended for use with GLOBAL eco components and fixtures marked for use with the GLOBAL eco system. To reduce the risk of fire and electric shock, do not use other components as part of this system.
2. Track installation is only to be performed by a certified electrician in accordance with the National Electrical Code and all local codes and standards.
3. The GLOBAL eco GES track system is designed to b e supplied by a single 120 volt branch circuit with a maximum capacity of 20 amps. The two circuit GLOBAL eco GET system is to be supplied by a balanced 120/240 volt, three-wire branch circuit with a maximum capacity of 40 amps.
4. Do not use this track with a power supply cord o r convenience receptacle adapter.
5. Do not install any fixtures closer than six inch es from combustible materials.
6. Do not install the track in damp or wet location s.
7. Do not install the track with electric power connected. Similarly, disconnect electricity when installing or removing fixtures or components or changing the configuration of the track.
8. Do not attach anything other than UL listed lighting fixtures marked for use with Nordic Aluminium GLOBAL eco system only to the track.

IMPORTANT

SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE WHEN ADDING FIXTURES OR CHANGING THE TRACK CONFIGURATION

Nordic Aluminium Inc,4300C Bankers Circle, Doraville, GA, 30360, Tel: 770-326-3331, Fax: 770-326-3353

Rev. 2
08 / 08

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>