Hollymatic 120 Precision Bulker Instruction Manual
- June 13, 2024
- Hollymatic
Table of Contents
Hollymatic 120 Precision Bulker
Product Information
- Model: 120 Precision Bulker
- For Serial Numbers Beginning with : 4600
- Manufacturer: Hollymatic Corporation
- Address: 600 E. Plainfield Road, Countryside, IL 60525
- Phone: 708-579-3700
- Fax: 708-579-1057
- Version: 3
- Weight: 40 lbs (67 lbs with stand)
- Portion Weigh t: 10 oz to 32 oz
- Portion Siz e: 4 1/8 inches wide x 1 1/2 inches thick, 4 3/8 inches to 9 5/8 inches long
- Adapter Rings : #42 and #52
- Compatible Brands : Hollymatic, Butcher Boy, Biro, Hobart
- Motor Specifications
- 115 Volt, 60 Cycle, 1 Phase, 2.5 Amp
- 220 Volt, 50 Cycle, 1 Phase, 1.2 Amp
- Overall Dimensions
- Length: 25 inches
- Width: 10 inches (Power Unit), 25 inches (Stand)
- Height (Adjustable) : 32 to 42 inches (Standard Rod Stand), 42 to 52 inches (Long Rod Stand)
- Height Center Forming Die : 19 to 29 inches (Standard Rod Stand), 29 to 39 inches (Long Rod Stand)
Product Usage Instructions
- Inspect the machine and ensure it has been made ready for operation by an authorized Hollymatic dealer before operating.
- Make sure all guards are in place before operating the machine.
- Always unplug the machine when not in use.
- Disconnect the machine from its power source before cleaning, servicing, or adjusting it.
- Do not operate the machine if the cord or plug are damaged.
- Avoid placing hands near moving parts.
- Only allow an authorized Hollymatic dealer to repair or adjust the machine.
- If an operator suspects that an interlock or safety device is not functioning properly, terminate the operation, unplug the machine, and call an authorized Hollymatic dealer to inspect and repair the machine.
OPERATORS MANUAL – PARTS LIST
FOR SERIAL NUMBERS BEGINNING WITH 4600
EVERY PERSON OPERATING THIS MACHINE MUST READ THIS MANUAL INCLUDING ALL SAFETY INSTRUCTIONS BEFORE ATTEMPTING TO OPERATE THIS MACHINE. PROPER GUARDS AND SAFETY DEVICES ARE INSTALLED FOR YOUR SAFETY. DO NOT OPERATE THE MACHINE UNLESS ALL GUARDS ARE IN PLACE.
COPYRIGHT © 2010 BY HOLLYMATIC CORPORATION MAY, 2016
HOLLYMATIC CORPORATION 600 E. PLAINFIELD ROAD COUNTRYSIDE, IL 60525
PHONE: 708-579-3700 FAX: 708-579-1057
SAFETY INSTRUCTIONS
WARNING TO ALL PURCHASERS, OPERATORS AND OPERATION SUPERVISORS
- MAKE CERTAIN EVERY PERSON WHO IS TO OPERATE THIS MACHINE HAS READ THIS MANUAL BEFORE BEING PERMITTED TO OPERATE THE MACHINE.
- HAVE ALL OPERATORS SIGN THE SIGNATURE PAGE FOUND AT THE END OF THIS MANUAL.
- FAILURE TO READ AND ADHERE TO THE FOLLOWING IMPORTANT INSTRUCTIONS COULD RESULT IN BODILY INJURY.
- READ THIS MANUAL COMPLETELY BEFORE OPERATING THE HOLLYMATIC MACHINE. ADDITIONAL MANUALS AS WELL AS REPLACEMENT SAFETY LABELS ARE AVAILABLE FROM HOLLYMATIC CORPORATION OR FROM YOUR LOCAL HOLLYMATIC
DEALER AT NO COST.
- DO NOT OPERATE THIS MACHINE UNTIL IT HAS BEEN INSPECTED AND MADE READY FOR OPERATION BY AN AUTHORIZED HOLLYMATIC DEALER.
- DO NOT OPERATE MACHINE WITHOUT ALL GUARDS IN PLACE.
- UNPLUG MACHINE WHEN NOT IN USE.
- ALWAYS DISCONNECT THE MACHINE FROM ITS POWER SOURCE BEFORE CLEANING, SERVICING OR ADJUSTING THE MACHINE.
- DO NOT OPERATE THE MACHINE IF THE CORD OR PLUG ARE DAMAGED.
- KEEP HANDS AWAY FROM MOVING PARTS.
- ALLOW ONLY AN AUTHORIZED HOLLYMATIC DEALER TO REPAIR OR ADJUST YOUR MACHINE.
- AT ANY TIME AN OPERATOR SUSPECTS THAT AN INTERLOCK OR SAFETY DEVICE IS NOT FUNCTIONING PROPERLY, THE OPERATION SHOULD BE TERMINATED, THE MACHINE UNPLUGGED AND AN AUTHORIZED HOLLYMATIC DEALER CALLED TO INSPECT AND REPAIR THE MACHINE. FAILURE TO FOLLOW THESE DIRECTIONS COULD RESULT IN SERIOUS PERSONAL INJURY.
SAFETY LABEL PLACEMENT
MODEL 120 BULKER 
ITEM : DESCRIPTION : PART NUMBER
- BULKER NAMEPLATE 900-0641
- ELECTRICAL SPECS DECAL ( 115V) 120-1100
- ELECTRICAL SPECS DECAL (230V) 120-1101
- cULus LABEL 900-1073
- NSF LABEL 2281
- WARNING LABEL 900-0640
- MADE IN THE USA LABEL 900-2003
- LABEL 4 AMP FUSE 900-1028
- LABEL 2 AMP FUSE 900-2006
120 BULKER LABEL LIST
SPECIFICATIONS
- PORTION WEIGHT : PORTION SIZE
- 10 OZ TO 32 OZ
- 4 1/8 INCHES WIDE X 1 1/2 INCHES THICK 4 3/8 INCHES TO 9 5/8 INCHES LONG
- ADAPTER RINGS
-
42 AND #52
- HOLLYMATIC, BUTCHER BOY, BIRO, HOBART
MOTORS
- 115 VOLT, 60 CYCLE, 1 PHASE, 2.5 AMP 220 VOLT, 50 CYCLE, 1 PHASE, 1.2 AMP
- OVERALL DIMENSIONS
- LENGTH: 25 INCHES
- WIDTH: 10 INCHES – POWER UNIT
- 25 INCHES – STAND
- HEIGHT (ADJUSTABLE): 32″ TO 42″ STANDARD ROD STAND
- 42″ TO 52″ LONG ROD STAND
- HEIGHT CENTER FORMING DIE : 19 TO 29 INCHES STD. ROD, STAND
WEIGHT
40 LBS.
67 LBS. (WITH STAND) 
ASSEMBLY
MAKE SURE GRINDER IS NOT PLUGGED INTO POWER SUPPLY. ASSEMBLE GRINDER HEAD WITH
WORM, KNIFE AND PLATE.
SECURE WITH ADAPTER RING.
PLACE CONVEYOR
BELTS ON SMALL DIAMETER REAR ROLLER AND PLACE ROLLER INTO NOTCHES AT REAR OF
CONVEYOR FRAME.
NOTE: SPACING OF CONVEYOR BELTS IS UNEQUAL – THE CLEARANCE BElWEEN THE
LEFT SIDE OF FRAME AND BELT SHOULD BE GREATER THAN ON THE RIGHT
SIDE. WITH THE BELTS EXTENDED TO FRONT OF FRAME, SLIP BELTS ONTO SMALL
DIAMETER PORTION OF DRIVE ROLLER.
NOTE: SQUARE END DRIVE ROLLER SHAFT MUST BE TO RIGHT. PLACE SHAFT INTO NOTCHES AT FRONT OF CONVEYOR. STRETCHING BELTS, PLACE THEM INTO GROOVES ON FRONT AND REAR ROLLERS.
FRONT ROLLER
SLIDE KNIFE INTO BLADE GUIDE. PRESS RELEASE PIN TO ALLOW KNIFE PAST LOCK PIN,
THEN RELEASE. WHEN KNIFE IS IN PROPER POSITION, LOCK PIN WILL ENGAGE KNIFE
HOLDING IT IN POSITION FOR ENGAGEMENT OF POWER UNIT CRANK ARM. SLIP KNIFE AND
GUIDE ONTO PINS EXTENDING FROM CONVEYOR FRAME AS SHOWN. SLOT IN KNIFE MUST
FACE EXIT END OF CONVEYOR.
FRONT ROLLER
SLIDE KNIFE INTO BLADE GUIDE. PRESS RELEASE PIN TO ALLOW KNIFE PAST LOCK
PIN, THEN RELEASE. WHEN KNIFE IS IN PROPER POSITION, LOCK PIN WILL ENGAGE
KNIFE HOLDING IT IN POSITION FOR ENGAGEMENT OF POWER UNIT CRANK ARM. SLIP
KNIFE AND GUIDE ONTO PINS EXTENDING FROM CONVEYOR FRAME AS SHOWN. SLOT IN
KNIFE MUST FACE EXIT END OF CONVEYOR.
SLIDE POWER UNIT ONTO PINS FROM OPPOSITE SIDE OF KNIFE. SLIDE FORMING DIE ONTO PINS AND Cl.AMP DIE, KNIFE GUIDE, CONVEYOR FRAME AND POWER UNIT TOGETHER WITH LATCHES ON EACH SIDE OF POWER UNIT.
FEED PAPER THROUGH SLOT IN BOTTOM OF DIE AND ONTO CONVEYOR AS SHOWN. PLACE LIGHT TENSION ON PAPER AND CHECK SIDE-TO-SIDE ALIGNMENT PAPER IN RELATION TO SLOT IN DIE. MOVE PAPER ROLL ON HOLDER TO ADJUST.
SLOT IN BOTTOM OF FORMING DIE
.ADJUST HEIGHT OF BULKER TO GRINDER. HOLDING HANDLE ON POWER UNIT, CAUTION: BE PREPARED FOR WEIGHT OF BULKER, LOOSEN CLAMP ON STAND AND MOVE UP OR DOWN TO CORRECT HEIGHT. RETIGHTEN CLAMP. SLIDE DIE INTO ADAPTER RING ON GRINDER AND SECURE WITH BAND CLAMP.
REPLACE GEAR MOTOR AND JUNCTION BOX, AND SLIP ONTO SQUARE END OF CONVEYOR DRIVE SHAFT. ROTATE CONVEYOR SHAFT FOR ALIGNMENT. TO ENGAGE RETAINING PIN ON GEAR BOX, PULL FRONT ROLLER FORWARD, SLIP PIN INTO CONVEYOR FRAME AND RELEASE.
UNHOOK CUT-OFF CONTROL AND DEPRESSING END OF LOCK PIN, SLIP THROUGH OPENING IN CONVEYOR FRAME AND SLIDE TO DESIRED SETTING. RELEASE LOCK PIN.
USE THE EDGE OF CUT-OFF CONTROL INDICATED BY ARROW TO SELECT PORTION WEIGHT.
READ PRIOR TO DISASSEMBLY AND CLEANING
OF ANY HOLLYMATIC EQUIPMENT
HOLLYMATIC EQUIPMENT CLEANING AND SANITIZING PROCEDURE
WARNING: ALWAYS DISCONNECT THE MACHINE FROM ITS POWER SOURCE BEFORE PERFORMING THE CLEANING OPERATION.
CAUTION: TAKE CARE WITH HOT WATER SO AS NOT TO BURN YOURSELF OR OTHERS
WHEN CLEANING.
CAUTION: Strictly follow the cleaning and disinfectant chemical
manufacturer’s directions with regards to dilutions, exposure times and
preventive measures to observe when making up, using and disposing these
solutions. Failure to do so may result in damage to machine components.
CAUTION: It is strongly recommended that protective gloves be worn when
using cleaning detergents, disinfectants and during the whole cleaning
process.
- CLEAN AND DEGREASE THE PARTS USING ANY APPROVED DETERGENT FOR FOOD EQUIPMENT, FOR EXAMPLE – Eco-Lab—Oasis 133-All Purpose Cleaner and Degreaser Concentrate
- RINSE THE PARTS THOROUGHLY AFTER DEGREASING, USING POTABLE WARM WATER [120 – 140?F]
- SANITIZE AND STERILIZE THE PARTS USING ANY APPROVED DISINFECTANT FOR FOOD EQUIPMENT, FOR EXAMPLE –
Eco-Lab-Ster-Bac or Ster-Bac Blue concentrate
DRY THE PARTS
Using an approved sterilized cloth, dry all parts after exposure to the
Sanitizing solution for recommended length of time [1 minute for the above
sanitizer], so there is no standing water on the part surfaces.
APPLY HOLLY FLUID
Apply Holly Fluid to all the outside surfaces of the sanitized parts for
longer life.
CAUTION
BEFORE CONNECTING TO POWER, MAKE SURE
- HANDS ARE CLEAR AND SWITCH IS OFF.
- USING 3-WIRE GROUNDED EXTENSION CORD
- PLUG INTO 115V, 1 PH, 60HZ POWER SUPPLY.
- (ALSO 220V, 1 PH, 50HZ ON 220V UNITS).
- CONNECT MEAT GRINDER TO PROPER POWER SUPPLY. PLACE SELECTOR IN “GRIND” POSITION.
- NOTE: IT IS RECOMMENDED TO OPERATE GRINDER — WITH FOOT SWITCH.
BULKING
TURN ON BULKER. TURN ON GRINDER. THE BULKER AUTOMATICALLY PORTIONS LOAF OF
MEAT TO SET WEIGHT. CHECK FIRST FEW PORTIONS FOR WEIGHT.
- (WEIGHT CAN VARY DUE TO FAT CONTENT, ADDITIVES, ETC.) MOVE ADJUSTOR
- (WITH GRINDER AND BULKER TURNED OFF) TO OBTAIN DESIRED WEIGHT PER PORTION. BULKER IS NOW READY FOR CONTINUOUS OPERATION.
DISASSEMBLY
CAUTION: UNPLUG GRINDER AND BULKER FROM POWER SUPPLY. REMOVE PAPER ROLL AND STORE IN A DRY AREA.
BEFORE BULKER IS DISASSEMBLED, REMOVE CONVEYOR DRIVE GEAR MOTOR FROM CONVEYOR. DISENGAGE CUT -OFF SWITCH FROM CONVEYOR FRAME AND HANG ON THE HOOK ON THE POWER UNIT.
DISASSEMBLE IN REVERSE ORDER OF ASSEMBLY.
NOTE: TO REMOVE BLADE, PRESS PIN ON BLADE LOCK TO RELEASE
CAUTION: BLADE IS SHARP. USE CARE WHEN HANDLING.
CLEAN-UP
ALL PARTS EXCEPT POWER UNIT MAY BE WASHED IN A SINK. USE HOT WATER.
CAUTION: DO NOT USE STEAM CLEANER ON BULKER PARTS.
DAMAGE MAY RESULT.
POWER UNIT: WIPE EXTERIOR CLEAN.
DO NOT USE HOSE OR IMMERSE IN WATER.
SERVICE
NOTE: THE HOLLYMATIC BULKER REQUIRES NO LUBRICATION, EXCEPT FOR A VERY
SMALL AMOUNT OF HOLLY LUBE ON CONVEYOR ROLLER SHAFTS. WHEN THE BLADE BECOMES
DULL, SHARPEN AS REQUIRED.
CLEANING NOTES
THE TRIP LEVER ON END OF CUT-OFF SWITCH SHAFT IS REMOVABLE–PULL STRAIGHT OFF
SHAFT.
THE BLADE LOCK MAY BE REMOVED FROM KNIFE GUIDE BY PUSHING SPRING OUT OF GROOVE
IN STUD AND LIFTING IT AND BLADE LOCK OFF STUD. FOR REASSEMBLY, REVERSE
PROCEDURE.
USE CLEANING TOOL (120-1150) TO REMOVE MEAT FROM GROOVES IN KNIFE GUIDE, AND
PAPER FEED SLOT IN FORMING DIE.
120-1232 CONVEYOR DRIVE GEAR MOTOR
IN ORDER TO INCREASE THE LIFE AND PERFORMANCE OF THE CONVEYOR DRIVE, WE
RECOMMEND REMOVING THE GEAR MOTOR FROM THE POWER UNIT BEFORE WASHING DOWN THE
CONVEYOR FRAME. STORE THE GEAR MOTOR IN A DRY PLACE.
| ITEM | QTY. | DESCRIPTION | PART NO. |
|---|---|---|---|
| 1 | 1 | ENCLOSURE WELDMENT | 120-1181 |
| 2 | 1 | PLUG & CORD | 120-1358 |
| 3 | 1 | CAUTION LABEL | 900-0640 |
| 4 | 1 | BULKER LABEL | 900-0641 |
| 5 | 1 | RING LOCK | 120-1079 |
| 6 | 2 | DRAW LATCH | 120-0063 |
| 7 | 2 | BOLT ASS’T. – LATCH | 120-0121 |
| 8 | 8 | POP RIVET FOR 1/8″ WORK THICKNESS | 100-0149 |
| 9 | 1 | “ON-OFF” SWITCH | 120-0018 |
| 10 | 1 | FUSE HOLDER | 680-2150 |
| 11 | 1 | GLASS TUBE 4 AMPERE FUSE | 120-0075 |
| 12 | 8 | #10-32 X 1/2 HHCS | 723040223 |
| 13 | 1 | BOTTOM COVER ASS’Y. | 120-1182 |
| 14 | 2 | #8-32 x 1/4 PAN HEADED SCREW | 712021640 |
| 15 | 2 | #8 INTERNAL LOCKWASHER | 752000640 |
| 16 | 1 | GUARD FOR ON-OFF TOGGLE | 2586 |
| 17 | 1 | 1/2″ INT. TEETH L/W | 758100640 |
| 18 | 1 | 115V POWER CORD ASSY | 120-0080 |
| 19 | 1 | “ON – OFF” Indicator PLT. | 120-1080 |
| 20 | 1 | SEAL FOR TOGGLE SWITCH | 500-1167 |
| 21 | 1 | TRIGGER RECEPTACLE & LEADS ASSEMBLY | 120-1209 |
| 22 | 2 | DRIVE NUTS – 1/2″ NOM. | 400-1150 |
| 23 | 1 | RECEPTACLE & LEADS ASSEMBLY | 120-1360 |
| 24 | 1 | TOP COVER | 120-1185 |
| 25 | 1 | STUD | 120-1152 |
| 26 | 1 | LOCKNUT | 120-1153 |
| 27 | 1 | GEARHEAD 6 :1 |
GEARHEAD 3 :1
| 120-1333
120-0201
28| 1| MOTOR, INDUCTION 110/115V, 1 PH, 60 HZ| 120-1332
29| 1| BRACKET MOTOR MOUNT| 120-1331
30| 1| PIN, MOTOR MOUNT| 120-1338
31| 1| COUPLER, CONVEYOR DRIVE| 120-1334
32| 1| #8-32 X 1/4 SET SCREW| 712023640
| ITEM NO. | DESCRIPTION | QTY. | PART NO. |
|---|---|---|---|
| 1 | MOUNT NG PLATE | 1 | 120-0169 |
| 2 | D N RA L 3″ LG | 1 | 120-1379 |
| 3 | GROUND NG BLOCK COVER YELLOW | 2 | 120-1373 |
| 4 | GROUND NG TERM NAL BLOCK | 2 | 120-1372 |
| 5 | TERM NAL BLOCK GRAY | 11 | 120-1369 |
| 6 | 2 POLE TERM NAL JUMPER | 1 | 120-1366 |
| 7 | 4 POLE TERM NAL JUMPER | 1 | 120-1368 |
| 8 | 3 POLE TERM NAL JUMPER | 1 | 120-1367 |
| 9 | MOUNT NG BRACKET (SAFETY SW TCH) | 1 | 120-0011 |
| 10 | ADAPTER FOR ONE SHOT T MER | 1 | 120-1370 |
| 11 | ONE SHOT T MER | 1 | 120-1371 |
| 12 | W RE, WH TE | 2 | 120-0086 |
| 13 | STA-KON FEMALE D SCONNECT | 2 | 879-1274 |
| 14 | MOTOR 115V 60 HZ | 1 | 120-0132 |
| 15 | MOTOR FAN | 1 | 120-1236 |
| 16 | #10-32 X 5/8 H.H.C.S | 7 | 723050223 |
| 17 | #10 SPL T LOCKWASHER | 11 | 753000591 |
| 18 | PULLEY-DR VE | 1 | 120-1345 |
| 19 | SET SCR. 8-32 X 1/4 | 2 | 712024599 |
| 20 | T M NG BELT | 1 | 120-0008 |
| 21 | BRACKET – FRONT CLUTCH | 1 | 120-1132 |
| 22 | CLUTCH BEAR NG | 2 | 120-0147 |
| 23 | SPROCKET-DR VEN | 1 | 120-0007 |
| 24 | BRACKET -REAR CLUTCH | 1 | 120-1133 |
| 25 | DOWEL P N 3/16 X 3/4 | 2 | 763062040 |
| 26 | WARNER CLUTCH FOR 115/220 V.A.C. | 1 | 120-0015 |
| 27 | ROLLP N 3/16 X 1-1/2 | 1 | 763141691 |
| 28 | CRANK ARM | 1 | 120-0013 |
| 29 | CAM FOLLOWER | 1 | 120-0010 |
| 30 | LOCKNUT | 1 | 99638A200 |
| 31 | TOE CLAMP | 2 | 120-1143 |
| 32 | #10-24 X 1/2 HHCS | 4 | 713040223 |
| 33 | MALE-FEMALE THREADED HEX STANDOFF #8-32 THREAD | 2 | 120-1380 |
| 34 | 8-32 x 1/4 LG PAN HEAD PH L PS MACH NE SCREW | 2 | 712024630 |
| 35 | SEMS – THREAD CUTT NG | 5 | 120-1248 |
| 36 | RECT F ER 400 V | 1 | 120-1375 |
| 37 | RELAY | 1 | 270-0132 |
| 38 | 1/4-20 X 1-1/2 H.H.C.S | 3 | 714140253 |
| 39 | 1/4 SPL T LOCKWASHER | 3 | 754000591 |
| 40 | GEARMOTOR CAPAC TOR – 5 µF | 2 | 120-1364 |
| 41 | #8-32 X 3/16 LG PAN HEAD PH L PS MACH NE SCREW | 2 | 712054630 |
| 42 | #4-40 X 3/8″ LG. PAN HEAD PH L PS SCREW | 2 | 120-1117 |
| 43 | PROX SENSOR – MAGNET C | 1 | 480-1541 |
| 44 | #10-32 X 5/8 LG HHCS SS | 1 | 723050240 |
| 45 | #4-40 HEX. NUT | 2 | 120-0110 |
| 46 | #4 NTERNAL LOCKWASHER – SW TCH | 2 | 120-0109 |
| 47 | SEMS (CHASS S MTG) | 1 | 120-1247 |
5/15 PAGE 15 M-1724
| TEM NO. | DESCR PT ON | TY. | PART NO |
|---|---|---|---|
| 1 | SW TCH BOX | 1 | 120-1144 |
| 2 | COVER – SW TCH BOX | 1 | 120-1145 |
| 3 | SCREW – SW TCH BOX | 2 | 120-1147 |
| 4 | EXTENS ON SPR NG | 1 | 120-1157 |
| 5 | M CRO SW TCH FOR TR GGER | 1 | 120-1376 |
| 6 | CORD FOR TR GGER SW TCH | 1 | 120-1378 |
| 7 | W RE TERM NAL | 1 | 120-0115 |
| 8 | CAM SHAFT | 1 | 120-1141 |
| 9 | SCREW, PAN HD #6-32 X 3/4 | 1 | 711061623 |
| 10 | NUT #6-32 | 3 | 731005140 |
| 11 | #6-32 X 1-1/2 R.H. MACH. SCR. | 2 | 711141440 |
| 12 | #6 NTERNAL LOCKWASHER | 5 | 751000640 |
| 13 | LOCK P N | 1 | 120-1148 |
| 14 | ROLL P N (SW TCH BOX) | 1 | 120-1149 |
| 15 | COMPRESS ON SPR NG (SW TCH BOX) | 1 | 120-1158 |
| 16 | TR P LEVER | 1 | 120-1140 |
| 17 | ACORN NUT | 1 | 120-1312 |
| 18 | SCREW | 1 | 120-1313 |
| 19 | #4 NTERNAL LOCKWASHER – SW TCH | 1 | 120-0109 |
120-1376 SWITCH ONLY
120-1390 SWITCH-PLUG & CORD ASSY (USA)
120-1209 RECEPTACLE W/LEADS
120-1399 CUT-OFF SWITCH ASSY W/PLUG (USA) SEE PAGE 20 & 20A FOR ILLUSTRATIONS
5/15 PAGE 17 M-1700
NOTE: SEE
POWER UNIT ASSY ON PAGE 12 & CHASSIS ASSY ON PAGE 14 FOR ELECTRICAL COMPONENTS
120-0080 POWER CORD ASSEMBLY
| 13 | 1 | WIRE, GREEN S LG | 905-1223 |
|---|---|---|---|
| 12 | 1 | WIRE, WHITE 7 LG | 905-122 |
| 11 | 3 | WIRE, BLACK 9 LG | 905-1226 |
| 10 | 2 | WIRE, RED 9 LG | 905-1221 |
| 9 | 5 | SOCKET CONNECTOR | 120-1297 |
| S | 5 | PIN CONNECTOR | 120-1296 |
| 7 | 1 | PLUG, 5 CIRCUIT | 120-1295 |
| 6 | 1 | RECEPTACLE, 5 CIRCUIT | 120-129 |
| 5 | 1 | CORD CONNECTOR W/NUT | 260-00 2 |
| 3 | 1 | WIRE TERMINAL | 120-0115 |
NOTES ASSEMBLEALITTERS EXCEPTITERGAFTER INSTALLING INTO POWER UNIT #120.0167 FINISH ASSEMBLY WITH ITEM G 2 USE A PRO.CRIMPERTIMODEL # 90871.1 TO CRIMP PINS & SOCKETS TO WIRE LEADS
120-1209 RECEPTACLE & LEADS ASSEMBLY
NOTES: 1. ITEMS 1,5 & 7 NOT USED FOR CANADA. SEE #120-1159 SWITCH-CORD ASSY. 2. USE A PRO-CRIMPER I MODEL # 90871-1 TO CRIMP PINS
|
---|---
|
10
|
1
|
WIRE, WHITE 7 1/2 LG
|
905-122
| 9| 1| WIRE, BLACK 7 1/2 LG| 905-1226
| S| 3| PIN CONNECTOR| 120-1296
| 7| 3| SOCKET CONNECTOR| 120-1297
| 6| 1| RECEPTACLE, CIRCUIT| 120-1292
| 5| 1| PLUG, CIRCUIT| 120-1293
| | 1| WIRE, GREEN 7 1/2 LG| 905-1223
| 3| 1| RING TERMINAL| 120-0115
| 2| 2| FLAG TERMINAL| 200-0S05
| 1| 1| 3-PIN RECEPTICAL| 120-1377
CUT-OFF SWITCH & CORD ASSEMBLIES
NOTE:
ATTACH THIS PLUG #120-1293 AFTER INSTALLING INTO POWER UNIT
OPERATOR’S SIGNATURE PAGE
WARNING: BEFORE”S ONIDE BELOW. THIS ENTIRE MANUAL MY SIGNATURE BELOW ATTESTS THAT | HAVE COMPLETELY READ AND UNDERSTAND THIS MANUAL. I REALIZE THAT THIS MACHINE, IF OPERATED CARELESSLY, CAN CAUSE SERIOUS INJURY TO MYSFLE AND OTHERS.
| NAME (PRINT) | SIGNATURE | DATE |
|---|---|---|
HOLLYMATIC CORPORATION 600 E. PLAINFIELD ROAD COUNTRYSIDE, IL 60525 Telephone: 708-579-3700
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>