vtech 556660 GGSW Go Go Smart Wheels Fast and Friendly Garage Instruction Manual

vtech 556660 GGSW Go Go Smart Wheels Fast and Friendly Garage

INTRODUCTION

Thank you for purchasing the VTech® Go! Go! Smart Wheels® Fast & Friendly Garage. Repair, fuel up, wash and race all in one place.
This multi-level garage is the best place in town to get your Speedy Race Car in tip-top shape!

INCLUDED IN THE PACKAGE

One SmartPointTM
Speedy Race Car

One nonelectronic car

One nonelectronic car

One ground floor base

One ground floor support

One main support

One SmartPointTM car wash base

One car wash roller

Two car wash supports

Track E

Four tracks (A, B, C, D)

One second floor platform

One SmartPointTM repair lift

One second floor support

One third floor platform

One SmartPointTM tuning station plate

One tuning station roof

One tuning station support

One exit gate support

One exit gate roof

One exit gate

One road sign

One track splitter

One gas pump

One plate

One hanging sign plate

One hanging sign support

Five screws

• Sticker Sheet
• Quick Start Guide

WARNING
All packing materials such as tape, plastic sheets, packaging locks, removable tags, cable ties, cords and packaging screws are not part of this toy, and should be discarded for your child’s safety.

NOTE
Please save this manual as it contains important information.

CAUTION
This package contains small screws. Adult assembly required.
For your child’s safety, do not let your child play with the toy until it is fully assembled.

If there are no locks inside the package, disregard this message.
Removing the Packaging Locks :

1. Turn the packaging locks anticlockwise several times.
2. Pull out the packaging locks and discard.

CAUTION:

This package contains small screws. Adult assembly required.
For your child’s safety, do not let your child play with the toy until it is fully assembled.

INSTRUCTIONS

Battery Removal And Installation

1. Make sure the unit is turned OFF.
2. Find the battery cover located on the bottom of the Speedy Race Car, use a screwdriver to loosen the screw and then open the battery cover.
3. Remove old batteries by pulling up on one end of each battery.
4. Install 2 new AAA (AM-4/LR03) batteries following the diagram inside the battery box. (For best performance, alkaline batteries or fully charged Ni-MH rechargeable batteries are recommended).
5. Replace the battery cover and tighten the screw to secure.

WARNING:

Adult assembly required for battery installation.
Keep batteries out of reach of children.

IMPORTANT: BATTERY INFORMATION

• Insert batteries with the correct polarity (+ and -).
• Do not mix old and new batteries.
• Do not mix alkaline, standard (carbon-zinc) or rechargeable batteries.
• Only batteries of the same or equivalent type as recommended are to be used.
• Do not short-circuit the supply terminals.
• Remove batteries during long periods of non-use.
• Remove exhausted batteries from the toy.
• Dispose of batteries safely. Do not dispose of batteries in fire.

RECHARGEABLE BATTERIES

• Remove rechargeable batteries (if removable) from the toy before charging.
• Rechargeable batteries are only to be charged under adult supervision.
• Do not charge non-rechargeable batteries.

LABEL APPLICATION

Please stick the labels to the play set as shown below :

ASSEMBLY INSTRUCTIONS

With the Go! Go! Smart Wheels Fast & Friendly Garage, safety comes first. To ensure your child’s safety, adult assembly is required.

1. Assemble and attach the car wash and ground floor components following the steps below:
   A. Insert the two Car Wash Supports into the Car Wash Base, as shown below. Make sure you hear a click sound to confirm the supports and base are firmly connected. Then insert the Car Wash Roller between the two supports as shown.B. Attach the Ground Floor Support to the Ground Floor Base, as shown below. A click sound confirms the support and base are firmly connected. Attach the Main Support to the Ground Floor Base as shown. Tighten it with three screws to secure.
   
   C. Attach the Car Wash to the Ground Floor Base, as shown below. Make sure you hear a click sound to confirm they are firmly connected.
   

2. Assemble and attach the second floor components following the steps below:
   A. Attach the Repair Lift and the Second Floor Support to the Second Floor Platform, as shown below. Make sure you hear a click sound to confirm they are firmly connected.
   
   B. Attach Track E to the Second Floor Platform, as shown below.
   Tighten it with two screws to secure.
   
   C. Attach the Second Floor Platform to the Car Wash Supports, Ground Floor Support and Main Support, as shown below. Make sure you hear a click sound to confirm they are firmly connected.
   

3. Assemble and attach the third floor components following the steps below:
   A. Attach the Tuning Station Roof to the Tuning Station Support, as shown below, then attach the Tuning Station Support and Tuning Station Plate to the Third Floor Platform as shown. Make sure you hear a click sound to confirm they are firmly connected.
   
   B. Attach the Third Floor Platform to the Second Floor Support and Main Support, as shown below. Make sure you hear a click sound to confirm they are firmly connected.
   

4. Assemble and attach the track components following the steps below:
   A. Insert the Hanging Sign Support to the Hanging Sign Plate, and then insert it to the Sliding Track A, as shown below. Insert the Track Switch Gate into Track B as shown. Make sure you hear a click sound to confirm the Track Splitter and the Track B are firmly connected.
   
   B. Connect Track C and Track D together, and then attach Track D to the Ground Floor Base, as shown below. Make sure you hear a click sound to confirm they are firmly connected.
   
   C. Attach Track B to Track C, the Second Floor Platform and the Main Support, as shown below. Make sure you hear a click sound to confirm they are firmly connected.
   
   D. Attach Track A to Track B, Main Support and the Third Floor Platform, as shown below. Make sure you hear a click sound to confirm they are firmly connected.
   

5. Assemble and attach the remaining components following the steps below:
   A. Attach the Spinning Plate to the Main Support, as shown below.
   Attach the Exit Gate Roof to the Exit Gate Support, as shown below. Make sure you hear a click sound to confirm they are firmly connected.
   
   B. Attach the Exit Gate Support, Exit Gate Handrail, Fuel Stop and Road Sign to the Ground Floor Base, as shown below. Make sure you hear a click sound to confirm they are firmly connected.
   
   Once you’ve completed the above steps, you are ready to play! You can also connect the garage to other Go! Go! Smart Wheels® track sets (each sold separately).
   

PRODUCT FEATURES

1. On/Off Switch
   To turn the unit On, slide the On/ Off Switch to the On ( ) position.
   To turn the unit Off, slide the On/Off Switch to the Off ( ) position.
   

2. Automatic Shut-Off
   To preserve battery life, the Go! Go! Smart Wheels® Speedy Race Car will automatically power down after approximately 60 seconds without input. The unit can be turned on again by pressing the light up button, pushing the car quickly, opening the bonnet or triggering a SmartPointTM location.

Note : This product is in Try-Me mode in the packaging. After opening the package, turn the vehicle off and on again to proceed with normal play. If the unit repeatedly powers down while playing, please install a new set of batteries.

ACTIVITIES

Speedy Race Car

1. Slide the On/Off Switch to turn the Speedy Race Car On. You will hear a song, fun phrases and sounds. The light will flash with the sounds.
   

2. Press the Light Up Button to hear fun sounds, songs, phrases and melodies. The light will flash with the sounds.
   

3. Open the Speedy Race Car’s Hood to hear fun sounds. The light will flash with the sounds.
   

4. Push the Speedy Race Car to hear fun sounds. If a melody is already playing, push the Speedy Race Car to add fun sounds on the top of the melody. The light will flash with the sounds.
   

5. For added fun, the Speedy Race Car interacts with the Go! Go! Smart Wheels® Fast & Friendly Garage. Simply put the Speedy Race Car on one of the track set’s six SmartPointTM locations to hear fun sounds, music, phrases and see the light flash. The Speedy Race Car also interacts with the other Go! Go! Smart Wheels® track sets (each play set sold separately).
   

Fast & Friendly Garage

1. Place the Speedy Race Car or any SmartPointTM vehicle (each sold separately) on any of the play set’s six SmartPointTM locations to hear fun sounds, music and phrases.
   

2. Place the Speedy Race Car on the Tuning Station, and then press the button to get the Speedy Race Car race ready.
   

3. Place the Speedy Race Car on the Repair Lift, and then press the button to raise the lift to give the Speedy Race Car a tune-up.
   

4. Place the Speedy Race Car on the Car Wash, and then push the handle to spin the roller to clean the Speedy Race Car.
   

MELODY LIST

1. Mulberry Bush
2. Little Bo Peep
3. Hey Diddle Diddle
4. Old MacDonald
5. Polly Put the Kettle On
6. Jack Be Nimble

SONG LIST

Song 1
I like to be at the front of the line
but when I’m with my friends, we all take turns.
When’s it my turn?
When’s it my turn?
Song 2
Here we go I’m in first
Here we go now we’re tied.
Here we go back in first,
All out on a speedy fun ride.
Song 3
Go! Go! Smart Wheels!
I’m a Go! Go! Smart Wheels Race Car.
I’m built for the fastest run. (Go! Go!)
Shift the gear, full speed ahead.
Let’s Go! Go! and see! (Go! Go!)
Song 4
Round and round the track we go
I am fast and the others slow.

CARE & MAINTENANCE

1. Keep the unit clean by wiping it with a slightly damp cloth.
2. Keep the unit out of direct sunlight and away from any direct heat sources.
3. Remove the batteries if the unit will not be in use for an extended period of time.
4. Do not drop the unit on a hard surface and do not expose the unit to moisture or water.

TROUBLESHOOTING

If for some reason the unit stops working or malfunctions, please follow these steps:

1. Turn the unit Off.
2. Interrupt the power supply by removing the batteries.
3. Let the unit stand for a few minutes, then replace the batteries.
4. Turn the unit On. The unit should now be ready to play again.
5. If the unit still does not work, install a new set of batteries.

IMPORTANT NOTE : If the problem persists, please call our Consumer Services Department at 1-800-521-2010 in the U.S. or 1-877-352-8697 in Canada, or by going to our website at vtechkids.com and filling out our Contact Us form located under the Customer Support link. Creating and developing VTech products is accompanied by a responsibility that we take very seriously. We make every effort to ensure the accuracy of the information, which forms the value of our products. However, errors sometimes can occur. It is important for you to know that we stand behind our products and encourage you to contact us with any problems and/or suggestions you might have. A service representative will be happy to help you.

NOTE

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna
• Increase the separation between the equipment and receiver
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected
• Consult the dealer or an experienced radio/TV technician for help

CAUTION
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

Supplier’s Declaration Of Conformity

47 CFR § 2.1077 Compliance Information

Trade Name: VTech®
Model: 1156
Product Name: Fast & Friendly Garage™
Responsible Party: VTech Electronics North America,
W. Shure Drive, Suite 200
Arlington Heights, IL 60004
Website: vtechkids.com

THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES.
OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS:
(1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE, AND (2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION.
CAN ICES-003(B)/NMB-003(B)

Visit our website for more information about our products, downloads, resources and more.
vtechkids.com
vtechkids.ca

Read our complete warranty policy online at
vtechkids.com/warranty
vtechkids.ca/warranty

References

• VTech Canada | Official Electronic Learning Toys & Games for Kids
• VTech Canada | Official Electronic Learning Toys & Games for Kids
• Best Kids Tech Toys | Electronic Learning Toys | VTech America
• Best Kids Tech Toys | Electronic Learning Toys | VTech America

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>