TOPPING M50 Digital Network Player File Reader User Guide
- June 13, 2024
- TOPPING
Table of Contents
TOPPING M50 Digital Network Player File Reader
Thank you for purchasing Lossless music player M50! M50 is a lossless music player that supports a wide range of music formats. It can access SD card / U disk / hard disk, can be connected wirelessly via Bluetooth, Airplay, DNA, and can also be connected to a computer as a USB bridge. We hope it could bring you more fun at enjoying music. Now we recommend you read this manual so that you can use all the features of M50 correctly.
Contents list
- M50 × 1
- Remote control × 1
- USB cable × 1
- DC cable × 1
- Bluetooth antenna × 1
- User manual × 1
- Warrantv card × 1
Note: You can download the drivers and user manual on http://www.topping.audio/.
Attribute
Measured | 11 .9cm x 11cmx3.8cm |
---|---|
Weight | 440g |
Power input | DC5V/1A (DCbase 5 5*2.1) |
Signalinput | USB-OTG• 2, USB OAC- TF cardslot, Bluetooth, WiFi |
Signaloutput | Bluetooth, USB-OTG. Optical. Coaxial. IIS |
Standby power consumption | <0.5W |
Power consumption | <1.SW |
TF card capacity | up lo 256 GB |
USB
| Hard disk driver| up lo 4 TB
Filesystem| Suppor t FAT/FAT32/NTFS
Bluetooth
| Input preference| LDAC >AAC> SBC
Outpt : preference
order
| LDAC > APTX > AAC > SBC
Front panel
-
Power button
Press and hold to power on/off. In the on state, a short press turns the screen off.
You can press any button on the front panel to light up the screen. -
Remote control receiver
Please point the top of the remote control at it when using the remote control -
Display
-
Previous*
- In playback interface, short press to play previous track, press and hold to rewind
- In other interfaces, short press to move to previous item, press and hold to move quickly.
-
Back
Short press to move to the previous menu, press and hold to go back to the main menu. -
Next*
- In playback interface, short press to play next track, press and hold to fast forward
- In other interfaces, short press to move to next item, press and hold to move quickly.
-
OK/Play/Pause*
In playback interface, short press to play/pause- In other interfaces, short press to make a selection
-
Playback menu
Press to enter the playback menu when in playback interface
Depending on the input, some buttons may be disabled under the playing interface.
Rear panel
-
Bluetooth input/output
-
IIS output
-
Optical SPDIF output
-
Coaxial SPDIF output
-
USB-OTG port
- Can connect a USB storage device or HDD (hard disk driver) to play music files.
- Can output to the USB DAC. Note that only one USB DAC can be connected at the same time.
-
USB DAC port
- In DAC mode, the M50 can be connected to a computer and used as a USB Bridge.
- In USB mode, you can access the TF card inserted in the M50 on your computer.
Set it here: [Main Interface – System Settings – USB Mode]
-
Power input (DC5V)
Side panel
TF card slot
- This slot is only for the standard TF card(Micro SD) and support a capacity up to 256GB.
- Insert: insert a TF card until is clicks into place. Make sure to insert the TF card in the correct direction.
- Remove: push the TF card into the TF card slot. The TF card will pop out.
Remote control
- Standby
- Previous*
- Back
- Next*
- Invalid button
- Equalizer setup
- Invalid button
- Invalid button
- OK
- Play/Pause
- Invalid button
- Playback menu*
- Brightness
Depending on the input, some buttons may be disabled under the playing interface.
Support range
Supported Audio Formats
|
APE
| Fast| 8kHz-384 kH z/ 16 b i t-24 bi t ( CUE supported )
---|---|---|---
Normal| 8kHz-384 kH z/16b i t-24bit (CUE supported)
High| 8kHz-384kHz/16bit-24bit
Extra high| 8kHz-96kHz/16bit-24bit
WAV| 6kHz-384kHz/16bit-32bit( CUEsupport,ed□TSnot supported)
FLAG| 8kHz-384 kHz/16b i t-24bit ( CUE supported )
AIFF| 8kHz -38 4kHz / 16b it-32bil
M4A| 8kH z-384 kHz/ 16b it- 24bi t
WMA| 8kHz -96kHz / 16bi t-24bit
WMALossless| 8kHz -96kHz / 16bi t-24bit
Mp2| 8kHz- 48kH z/16bi t
Mp3| 8kHz- 48kH z/16bit ( CUE suppo rted )
AAC| 8kHz-48k Hz/ 16bit
OGG| 8kHz- 48kH zl 16bit
DSF| DSD64-DSD256
DFF| DSD64·DSD256
*Above all 64k filesdo not support
USBDAC IN
| PCM 44.1kHz-384kHz/16bit-32bit
□so OS064-0SD256 (Native) , DSD64·DS0126 (Dop)
USB-OTGOUT
| PCM 44 .1kHz – 384kHz /16b it- 32 bit
DSD OSD64-DSD256 ( Native) . DSD64-DSD256 (Dop )
BTIN| S BC/AAC/LDAC
BT OUT| SBC/AAC/APTX/LDAC
OPT /COAXOUT
| PCM 44 .1kHz-192kHz/16b it-24b it
DSD DS D64 ( Dop )
IIS OUT
| PCM 44.1kHz-384kHz/16bit-32bit
DSD DSD64-DSD256 (NaHve)
Playback
Bluetooth
- In [Main Interface – NET settings – Bluetooth setting], turn on and connect the Bluetooth
- Note the Hiby link function in [Bluetooth setting] needs to be turned off first, because using Hiby link function needs to occupy Bluetooth.
- The picture above shows the playback interface when the M50 is used as a Bluetooth receiver. the M50 can also be used as a Bluetooth transmitter to connect to a Bluetooth DAC or Bluetooth headphone.
USB Storage Device/HDD/TF card
- Plug your USB storage device/HDD into the USB-OTG port or insert the TF card into the TF card slot. Folders and music files are displayed on [Main Interface – Music Browser] when loading is complete. Then you could select songs to play.
- Playback menu
- You can add this song to My Favorite/Playlist, or delete it, and you can also set the Playback Mode.
Playback Mode
- List loop
- Order
- Single cycle
- Shuffle
Connect to PC and use as USB Bridge
- In [Main Interface – System Settings – USB Mode], set the USB mode of the M50 to “DAC” and connect to the computer via the USB DAC port.
- Only able to control previous/next/play/pause on the computer.
Airplay/DLNA
- In [Main Interface – NET Settings – WiFi Setting], turn WiFi on and connect.
- Turn on the Airplay or DNA function in [WiFi Setting] according to your usage needs.
- Connect the Mobile Phone/Tablet to the same network as M50.
- Tap the AirPlay icon on the iOS device, and select M50 from the displayed devices. For Android devices, open the app that supports DNA playback and select M50 as the receiving device.
- Play the music file on the Mobile Phone/Tablet.
Note: Only able to control previous/next/play/pause on mobile phone.
Output
| BT OUT| USB-O TG OUT| SP DIF/IIS OUT
---|---|---|---
BT IN| __| |
USB Stor age Oevice/HOO/TF card IN| | |
USB DAC| | |
Airplay /DLNA| | |
- Output priority: Bluetooth > IIS > USB-OTG > SPDIF
- SPDIF output or IIS output can be selected through [Main Interface – Play Settings – Output Mode]. If you need to use USB-OTG output, please do not set it to IIS output.
Operation
- Hiby Link [Main Interface – NET Settings – Bluetooth Setting – Hiby Link]
- Install the HiByMusic app on your Android or iOS smartphone and you can control the M50 from afar using Bluetooth, for browsing, playing, skipping tracks, etc.
- EQ Setting [Main Interface – Play Settings – EQ]
- Press the “Previous” or “Next” button to switch the EQ mode:
- Off/Custom/Heavy/metal/Blues/Vocal/Dance/Pop/Jazz/Classic/Rock
- If chose the custom mode, press the OK button to enter the custom setting, then
- press the “Back” or “Play Menu” button to switch the frequency, press the “Previous” or “Next” button to change the boost. Finally, press the OK button to save the settings.
- Firmware Update [Main Interface – System Settings – Firmware Update] Download the firmware to the TF card, and then select this option to upgrade the firmware.
- IIS Settings [Main Interface – Play Settings – IIS Phase/lIS DSDR/DSD Flag] IIS Phase: STD / REV
IIS DSDR: LRCLK/ DATA
DSD Flag: Pin15 / Pin14
Bluetooth Input
USB Storage Device/HDD/TF card
Connect to PC and use as USB Bridge
Airplay/DLNA
Bluetooth Output
USB-OTG Output
SPDIF/IIS Output
Documents / Resources
|
TOPPING M50 Digital Network Player File
Reader
[pdf] User Guide
M50 Digital Network Player File Reader, M50, Digital Network Player File
Reader, Network Player File Reader, Player File Reader, File Reader
---|---
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>