WILLIAMSAV AN C5 Annotation Pro Video Processor User Guide
- June 13, 2024
- WilliamsAV
Table of Contents
Annotation Pro
AN C5
General Installation
Connecting the Video Source and Outputs
A video source provides the Annotation Pro a video image.
The Annotation Pro incorporates any annotations, then outputs the combined
annotations and video image to a display. Examples of video sources include
DVD players, computers, cameras, and television sets. Outputs can be to
projectors, monitors or other display devices. In the Annotation Pro, the
source can be from HDMI or USB.
Note on HDCP
HDCP functions are only available on the Annotation Pro Plus (AN C5 P).
HDMI Connectors
To connect HDMI video:
- HDMI Input into Annotation Pro: Using HDMI video cable, connect the Annotation Pro’s HDMI In on the back panel to HDMI out on a HDMI video source.
- HDMI Output from Annotation Pro: Using HDMI video cable, connect the Annotation Pro’s HDMI Out to HDMI In on a HDMI video source.
USB Connectors
Connect the device to one of the USB ports on the back of the Annotation Pro.
The system supports up to 5 USB 3.0 devices, and can support more with a hub.
Connecting Physical Controllers
IMPORTANT: Be sure to power down the Annotation
Pro before connecting or disconnecting any controllers.
The Annotation Pro will automatically detect installed controllers once
powered on. If you change controllers or add a new controller, you need to
power down, install the new controller(s), then power the device on.
Connecting a Keyboard, Tablet or other USB Devices Connect the device(s) to
any USB port on the Annotation Pro. The system supports up to 5 USB 3.0
devices.
Connecting the Phoenix-style Connector for Power
Connect the wires from your remote power controller (or other device) to the
Annotation Pro’s Phoenix-style connector (green connector labeled PWR SW).
When the power control relay is enabled, the Annotation Pro will power on or
off, as a toggle.
Connecting a Mouse Device via USB
Connect the mouse device to a USB port on the back of the Annotation Pro.
Connecting Touch Screens and Whiteboards
The Annotation Pro is compatible with many types of touch screens. Install the
HID touch screen to the monitor as directed by your touch screen man
ufacturer.
Power On
NOTE: In order for the Annotation Pro to properly sync with the video
signals, the sources should be turned on first.
To power on the Annotation Pro:
- Plug the power cord into the back of the Annotation Pro and then into any grounded outlet.
- Plug the power cords from any video source(s), controller(s), and display(s) into any grounded outlet.
- Turn on each of the connected units, and then press the power button on the front panel of the Annotation Pro.
After a moment, the Annotation Pro splash screen will appear, followed by the initializing of the ports, and ending with a copyright message.
Basic Configuration
Main Menu Basics
The main menu is a large, hidden main menu system mostly used for setup and
configuration.
Use a keyboard to access this menu for initial configuration. This menu will
need to be accessed to get your device connected to the network.
Activating the Menu
Keyboard: Press Setup Menu (Print Screen) key.
Touch Screen (or Whiteboard): Tap the upper center function area.
Making Menu Selections
Keyboard: Use arrow to move to your selection and press the Enter key.
Touch Screen (or Whiteboard): Tap the screen over the option you want to
select.
Selecting Video Sources
- Activate the main menu.
- Select Display. The Display menu appears.
- Select Video Source. The video source menu appears.
- Select from HDMI, USB, or chalkboard.
- Exit the menu system.
Calibrating Touch Screen Controllers
Calibration ensures an intuitive and precise feel to drawing and marking over
the particular monitor you are using.
Calibrations are automatically saved for each video port.
If you move a touch screen to a different port, run the calibration again. If
you have a touch screen display with multiple video inputs, you should
calibrate the touch screen for each input.
All calibrations are stored in battery backed-up memory.
The most recent calibration will be recalled any time power is cycled off and
on.
From the Menu System
-
Activate the menu system. The Main Menu appears.
-
Select Devices. The Devices menu appears
-
Select Calibration. The Calibration Menu appears.
-
In the Calibration Menu, select the controller you want to calibrate. The calibration screen for the selected controller appears.
-
Follow the calibration instructions displayed on-screen.
As you touch the target, it will disappear and the next target will appear. Repeat until all 12 targets have been calibrated. After you perform final calibration procedures, the Calibration dialog automatically disappears, and you return to the menu system. -
Exit the menu system. Repeat this process for each video input on your touch screen display.
Annotation Control App
The Annotation Control app is available from the Apple App Store for iOS
devices, and allows you to annotate directly from your iPad or other Apple
products.
To annotate from the app, your Apple device must be on the same wi-fi network
as your Annotation Pro system.
Open the app and select the Connect icon. Find your Annotation Pro system in
the list of available systems and select it. Once connected, draw with your
fingers to make any desired annotations.
For more details and configuration options, see the full user manual.
For Additional Information
This manual is a quick start guide for getting your Annotation Pro up-and-
running. It covers basic cable connection and setup. Most features and
customization options are not documented in this manual.
For additional information, feature instructions, warranty information and
more, please download the full user manual from the Annotation Pro product
page on Williams AV’s website.
info@williamsav.com /
www.williamsav.com
800-843-3544 / INTL:
+1-952-943-2252
© 2021, Williams AV, LLC MAN 265C
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>