i-PRO WV-QWL501 Wall Mount Bracket Instruction Manual

Specifications

{4-23/32 inches (W) x 8-21/32 inches (H) x 10-19/32 inches (D)}
Mass:| Approx. 2 kg {4.42 lbs}
Finish:| Aluminum die cast
Heavy salt damage prevention coating i-PRO white
Others:| Heavy salt damage prevention (ISO14993-compliant)

Precautions for installation

• In order to prevent injury, the product must be securely mounted to the wall according to the installation guide of this bracket.

• Installation place
  Salt damage prevention is applied to this product. However, it is not completely anti-corrosive.
  Therefore, consider a place for installation where direct splash of seawater can be avoided. Especially when installing this product in a seashore area or a place where a snow-melting agent is applied, and also where rainwater is avoided, it is recommended to regularly clean and rinse off salt with water. In case of installing this product in a seashore area, regularly check the status of equipment. (Replace the parts as required.)

• Mounting method for this product
  This product is designed to be mounted on a wall. If it is mounted on a desktop or at a slant, the camera may not work correctly and its lifetime may be shortened.

• Make sure to remove this product if it will no longer be used.

Standard accessories

Operating Instructions (this document) ………………………………… 1 pc.
Cable cap ………………………………………………………………………….. 2 pcs.
Camera mounting screw (Hexagon screw (M6)) …………………… 5 pcs.
(of them, 1 for spare)

Other items that are needed (not included)

Fixing screw (M10) or anchor ……………………………………………………………………………………….. 4 pcs.

IMPORTANT

• Minimum pullout strength: 823 N {185 lbf} (per 1 pc.)
• Refer to our technical information website for information on the minimum pull-out strength.
• Considering the material and strength of the area where the product is to be installed, prepare the screws according to the total weight of the camera and peripheral environment. Use the corrosion-resistant screws, or apply caulking to the screws to be used for fixing the framework and this product.

Parts and functions

Installation/Connections

Be sure to read “Precautions” and “Precautions for installation” before installation.
Refer to the operating instructions of the camera or the bracket for details including the camera or bracket mounting, their adjustment and the cable connection.
The installation of the wall mount bracket is roughly divided into 2 methods.
Refer to the applicable description.

• When laying cables through the cable access hole (front)
• When laying cables after drilling a hole through the wall

■ When laying cables through the cable access hole (front)
Step 1
Decide the mounting position and then drill holes for fixing screws or anchors in the wall.
Procure 4 pieces of M10 fixing screws or anchors to secure the this product on the wall.
For screw and anchor, make sure to use the one made of stainless steel, or enough salt damage prevention is applied. The hole diameter for fixing screws or anchors shall be decided in
accordance with the fixing screws or anchors to be used. A hole on the wall with a diameter of 30 mm {ø1‑3/16 inches} or less for a fixing screw or an anchor can be hidden with this product.

Step 2
Make a slit in the center of the cable cap (accessory) with a cutter.

Step 3
Pass the cable cap through the cable and then pass the cable into this product. Mount the cable cap to the cable access hole (front).
Refer to each manual of the camera and the bracket for further information about the length of the cable to be pulled out from the camera mounting part.

Step 4
Mount another cable cap (accessory) on the cable access hole (rear) on the plate on the rear side of the bracket.

Step 5
Mount this product on the wall with fixing screws (4pcs.) (M10: locally procured).

Minimum pull-out strength: 823 N {185 lbf}/per 1 pc.

Step 6
Seal the slit of the cable cap for the prevention of water leakage.

Step 7
Refer to each manual of the camera and the bracket for further information about cable connection and how to install the camera or the bracket.

■ When laying cables after drilling a hole through the wall
Step 1
Decide the mounting position, and drill a hole for a fixing screw or an anchor and a hole for cable installation in the wall.
Procure 4 pieces of M10 fixing screws or anchors to secure the this product on the wall.
For screw and anchor, make sure to use the one made of stainless steel, or enough salt damage prevention is applied. The hole diameter for fixing screws or anchors shall be decided in  accordance with the fixing screws or anchors to be used. A hole on the wall with a diameter of 30 mm {ø1-3/16 inches} or less for a fixing screw or an anchor can be hidden with this product.

Step 2
Mount the cable cap (accessory) on the cable access hole (front).

Step 3
Make a slit in the center of another cable cap (accessory) with a cutter.

Step 4
After removing the screws (4pcs.) from the rear side of the bracket, remove the plate and mount the cable cap in which a slit was made in Step 3 on the cable access hole (rear).

Step 5
Pass the cables from the wall through the cable cap (with a slit) on the plate and then through this product.
Refer to each manual of the camera and the bracket for further information about the length of the cable to be pulled out from the camera mounting part.
Secure the plate with the screws (4pcs.) removed in Step 4 on the rear side of the bracket.
(Recommended tightening torque: 0.78 N·m {0.58 lbf·ft})
Seal the slit of the cable cap for the prevention of water leakage.

Step 6
Mount this product on the wall with fixing screws (4pcs.) (M10: locally procured).

Minimum pull-out strength: 823 N {185 lbf}/per 1 pc.

Step 7
Refer to each manual of the camera and the bracket for further information about cable connection and how to install the camera or the bracket.

i-PRO Co., Ltd.
https://www.i-pro.com/
© i-PRO Co., Ltd. 2022

Ns0522-0
Printed in China

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>