Jiasibei GM 01 Magnetic Wireless Poldable Power Bank User Manual
- July 23, 2024
- Jiasibei
Table of Contents
Jiasibei GM 01 Magnetic Wireless Poldable Power Bank User Manual
Product Introduction
Thanks for choosing us! This is a magnetic suction wireless power bank,When you use the magnetic series mobile phone, it can be attached to the back of the mobile phone and easily taken away;It can charge tablets, mobile phones, game consoles, e-books, digital cameras, Airpods and other devices. Please read the manual carefully before using the product, and keep properly for checking.
Operation Steps
Charge the wireless power bank
The one endof usb cable is connected to the mobile power supply, and other is connected to the adapter (not include and need support the PD QC AFC protocol) ,then plug the adapter into the mains,the power bank’s light flashes,that indicate enter to charging state (4 lights each represents 25% power, 1-25%,2-50%, 3-75%, 4-100%) When all 4 lights are on and not flashing,the charging is complete.
Use magnetic wireless power bank to charge phone wirelessly
Take out the wireless power bank, Press the switch button once, after the light turns on,put the magnetic function phone on the wireless power bank,the built-in magnet of the wireless charger will automatically align and accurately adsorb to the mobile phone ,and then start to wireless charging.
Use mobile power to charge the mobile phone wired
Use one end of the standard usb cable to connect he the mobile power supply,other end is connected to the phone, the phone enters the charge power status (power supply is PD protocol, mobile phones that support PD fast charge protocol can charge quickly . Mobile phones that do not support PD protocol can also be charged, but they must use a standard Type-C cable)
Note: This package does not contain USB C-Lighting data cable, please purchase separately.
Using Instructions
- The magnetic suction function is only applicable to magnetic phone series, For example: Apple 12/13/14/15 series, other mobile phones are recommended to use USB power supply as much as possible.
- It is recommended to use a magnetic phone case or use it in bare phone,and must keep away from metal foreign objects when using, so as not to affect charging.
- Take out the wireless mobile power, press the switch once candetect the power,and at the same time turn on the wireless charging function, then power light on the power bank will be on. After fully charged, the product will automatically enter the standbystate.
- When only one indicator light of the power bank is on and flashes, the host battery is insufficient, please charge the product.
- Open wireless mobile power switch,it will automatically read if thereis device on the power bank that need wireless charging when 30 seconds didn’t read need charging equipment, or separated the devicefrom mobile power more than 30 seconds, mobile power supply will default no equipment to charge, and will automatically shut down. Use again please restart the switch,that can avoid wasting power.
- If you find that it cannot be charged, please check whether the wiring is normal and firm; or whether the power adapter is suitable,it is recommended to use a regular brand power adapter for charging.
- When charging the power bank, the wireless charging will be converted to 5w slow charging mode, and when the wireless charging is used alone, it will be switched to 15w fast charging mode.
- The heating of the mobile power supply when wireless charging is normal, and the charging power will be automatically adjusted to 5w when the product is heating.
- Simultaneous charging of wireless charging and wired charging will switch to 5w charging mode.
Bracket use scenario
Note: This product is suitable for smartphone products with magnetic suction wireless charging function. When using wireless products without magnetic suction function, please use a protective case with magnetic suction function. If you install additional magnetic suction coils or magnetic disks, it is recommended to use “C” type metal magnetic disk products, and it is not recommended to use “O” type magnetic suction rings. Product. O-type products are seriously heated due to physical phenomena.
Product Specification
Warnning
- The battery power of this product is low when leave factory, please charge it fully before use;
- Please do not fully discharge the power in the power supply before recharging,to keep product lifetime.
- If you do not use the product for a long time, please fully charge the product at least once every 1 month;
- Please use the standard accessories of the product. If the product is damaged due to the use of non-standard accessories, it will not be covered by the warranty;
- Dismantling the product privately, if the product is damaged, it is not covered by the warranty;
- It is forbidden to disassemble, hit or throw this product into fire water;
- Do not store this product in dusty, high or low temperature places (Temperature range -10℃—+40℃);
- Do not place this product in a humid environment, pay attention to waterproof and moisture-proof;If you need to clean it, please use a soft cloth to clean the product;
- To avoid accidents, please keep product away from children.
FCC Warning
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions:
(1)This device may not cause harmful interference, and
(2) this device mustaccept any interference received, including interference
that may cause undesired operation.
Any Changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in are
sidential installation. This equipment generates uses and can radiate
radiofrequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is noguarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged totry to correct the interference by one or more of
the following measures: -Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help.
The FCC certification of this device refers to RF exposure testing perfomed in
typical operating conditions, where a person is no closer than 0 centimeters
from the device surface at all times,except for non-repetitivepatterns with
transient time intervals in the order of a second. Only in the stated
conditions, the device is shownto fully comply with the FCC RF Exposure
requirements of KDB 447498.