FIAMMA M0_IS_98690M087 Carry Bike Motor Lift 77 Installation Guide

FIAMMA M0_IS_98690M087 Carry Bike Motor Lift 77

Product Information

The Bicycles Carrier is a product designed for safely transporting bicycles on vehicles such as motorhomes. It is suitable for use with 12V power supply. The product comes with a comprehensive user manual that provides installation and usage instructions in multiple languages.

Package Contents

• M2x – 2 pieces
• D2x – 2 pieces
• E4x – 4 pieces
• G2x – 2 pieces
• F2x – 2 pieces
• H2x – 2 pieces
• B – 2 pieces
• B2 – 2 pieces
• A – 1 piece
• I2x – 2 pieces
• C – 1 piece
• Q – 1 piece
• M6 – 14 pieces
• U – 1 piece
• M6 – 16 pieces
• L – 2 pieces
• R – 1 piece
• M6x50 – 8 pieces
• V – 1 piece
• M6x45 – 2 pieces
• S – 1 piece
• 6,4×12,5×1,6 – 4 pieces
• T – 1 piece
• M6x55 – 2 pieces
• W – 1 piece
• M6x60 – 2 pieces
• 2 – 1 piece
• 60 cm – 1 piece
• 78-94 cm – 1 piece
• 128 cm – 1 piece
• CARRY-BIKE – 1 piece
• 44 cm – 1 piece
• 68-108 cm – 1 piece
• 19 cm – 1 piece
• 16 cm – 1 piece
• 15kg x4 – 1 piece
• 30kg x2 – 1 piece
• 60kg – 1 piece
• 18.3 kg – 1 piece

Product Usage Instructions

Installation Instructions
Before installing the product, it is important to check that nothing has been damaged or deformed during transport. If there are any doubts or questions regarding the installation, usage, or limitations of the product, it is recommended to contact the dealer. The installation should be carried out by qualified personnel in compliance with local regulations.

Usage Instructions

• Step 1:
  Check the strongest points on the vehicle’s wall where you can fix the brackets before installing the product.

• Step 2:
  Cut the tubes (B) according to the desired vertical spacing.

• Step 3:
  Attach the tubes (B) and brackets (H, W, UQ, S) as shown in the diagram.

• Step 4:
  Ensure that the fork is not fully tightened to the tube. Leave a 2mm space.

• Step 5:
  Connect the power supply to the 12V supply connection. Ensure that the product is only connected to a 12V power source and never to a different voltage. It is advisable to disconnect the vehicle’s battery during installation for safety reasons.

Note:
The manufacturer will not be held liable for damages caused by faulty installation or connection of the product, mechanical influences, or overvoltage.

Package contents

Dimension

Installation instructions

Check that nothing has been damaged or deformed during transport. In the event of doubts or questions concerning the installation, use or limitations of the product, contact the dealer. We recommend that the installation is carried out by qualifi ed personnel and in compliance with current local regulations.

Before installing the product, check the strongest points of vehicles’s wall, where you can fi x the brackets.

Connections

• Supply connection 12V ==
• This product works at 12V ==, never connect to a different voltage.

For safety reasons it is advisable to always disconnect the battery in the vehicle and therefore to work without current during installation. Choose the safest and shortest installation route for the power cable. Reduce the length of the power cable as needed. Use only cable clamps suitable for the diameter of the power cable for the connection to the terminal box.

If incorrect terminals are used, this may cause a voltage drop and increase heat generation on the terminal.

The manufacturer shall not be held liable for claims for damages arising from the following:

• Faulty installation or connection of the product.
• Product damage caused by mechanical infl uences and overvoltage.
• Changes to the device without the express authorisation of the manufacturer.

For safety reasons we advice to make the electric connections as indicated on the diagram. When the ignition key is turned, the relay (*not supplied) cuts off the current to the electric motor, to avoid any accidental opening of the awning when the vehicle is moving. The open-close button is already wired.

Once the electrical connections have been made, it is advisable to carry out a general function test by holding down the button for lowering and raising the rail support base, checking that the symbols on the button correspond. If pressing the button does not trigger the movements, check the connection of all cables and contact service if necessary.

WARNING:
The product is not equipped with an automatic stop system, so when the moving part of the structure is close to the fi xed structure during closing, the button must be released (to prevent the two structures from interfering).

During the closing movement, check that there are no elements (hands, objects, etc.) obstructing the movement.

Before leaving, hook always the two security straps.

Instructions for use

In the event of a motor failure (with the rail support base down), remove the bikes from the Carry-Bike and manually lift the frame until it is completely closed, securing it with the straps. Then contact service.

In case of problems please contact your local dealer indicating the data on the nameplate. Consult our website for spare parts drawing.

Attention:
keep the following labels and affi x them to the Carry-Bike rails.

Safety instructions

• Read the following instructions and warnings carefully; failure to observe these installation and usage instructions as well as the laws for driving in the relevant country may cause severe harm or damage for which the manufacturer declines all responsibility. Before installation, ensure compatibility with the vehicle on which the product must be installed.
• In the event of an accident involving the vehicle and/or the product, ensure that the product has not been damaged. In the event of damage, contact your local retailer before moving the vehicle.
• Fiamma declines every responsibility for any modifi cation of the product that may cause damage and/or injury to things and people.
• Checking that the wall/rear door is suffi ciently solid and suitable for guaranteeing the resistance of the anchoring points is always mandatory. If not, strength and compliance with the maximum load indicated in the instructions are not guaranteed and it will be necessary to reinforce these points.
• After having positioned the Carry-Bike on the rear axle of the vehicle, the normal weight distribution on both axles would be modifi ed. This variation must not exceed the maximum permissible axle load.
• Never exceed the maximum permitted length and the total weight of the full-load vehicle.
• Make sure that loading occurs following a correct weight distribution; it must be uniformly distributed (the heaviest bike must be placed near the wall of the vehicle) to ensure better stability.
• Always give warnings about the presence of the Carry-Bike on your vehicle, using a clearly signal for leaning loads and, in case of limited rear visibiliy, use the additional rear-view mirrors.
• Take into account the presence of the Carry-Bike, paying attention during driving and expecially during reversing manoeuvres, particularly if you have parking assist system. Always comply with speed limits and the Highway Code.
• The speed should always be suitable to traffi c conditions and towed load. In case of use of the bike carrier with tow make sure that the tow hook is always accessible and the corner mobility of the tow is guaranteed (volume measuring din 74058).
• Check periodically the bicycle rack to make sure it is fi rmly attached, especially during the fi rst kilometers of after long trips to avoid damages of the Carry-Bike/vehicle. Make sure the belts are not loose and that the holding brackets have not shifted. Replace worn components immediately.
• It is advisable to remove the batteries from bicycles, before loading them on the Carry-Bike while traveling.
• It is recommended to rotate the handlebars of bicycles to avoid damage to the vehicle wall, for which Fiamma declines all responsibility.

Accessories

Warranty Fiamma

• In case of defects with regards to materials and manufacturing, the customer is entitled to the warranty
• In accordance with local laws and regulations of the country in which the product was purchased.

Declaration of Conformity

EU Declaration of Conformity (DoC)

Date 05/10/2022

We,

• Company name: Fiamma S.p.A.
• Postal address: Via San Rocco, 56
• Postcode and city: Cardano al Campo – (Varese)
• Telephone number: 0331/709111
• E-mail address: fiamma@fiamma.it.

Declare that the DoC is issued under our sole responsibility and belongs to the following product:

• Apparatus model / Product: Carry Bike motor kit
• Trademark: Fiamma
• Model/Type:
  • 02096-29-
  • Motor Lift 77

The object of the declaration described above is in conformity with the relevant Union harmonisation legislation:

• 2014/30/EU Electro Magnetic Compatibility Directive – EMCD.
• 2014/35/EU Low Voltage Directive – LVD.
• IEC 62368-1:2014 – LVD.
• 2011/65/EU Restriction of the use of certain hazardous substances Directive – RoHS.
• ECE/ONU/R10 Uniform provisions concerning the approval of vehicles with regard to electromagnetic compatibility – ECE ONU R10.
• EN 55014-1:2006 + A1:2009+ A2:2011 – RCM.
• EN 61000-3-2:2016 – RCM.
• EN 61000-3-3:2020 – RCM.
• EN 55014-2:2015 – RCM.

The following harmonised standards and/or technical specifications have been applied

Quality System Manager
Cerutti Davide

Fiamma S.p.A. – Italy
Via San Rocco, 56 21010 Cardano al Campo (VA).

fiamma.com

All rights reserved.

Fiamma S.p.A.
reserves the right to modify at any time, without notice, prices, materials, specifi cations and models or to cease production of any model.

References

• amma.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>