Door Awning Sophia 1600 Grey Canopia Instruction Manual

June 13, 2024
CANOPIA

Door Awning Sophia 1600 Grey Canopia

IMPORTANT!
Please read these instructions carefully before starting assembly. Keep these instructions in a safe place for future reference.

www.canopia.com

A member of Palram Industries Ltd.

HAVE A CONCERN?

WE CAN HELP.
Before returning your purchase:

You didn’t find what you were looking for?
We can help at canopia.shop/support

Still can’t find what you are looking for?Please see next page for local customer care.

WE ARE HERE TO HELP

For general questions: canopia.com/contact-us

USA
877-627-8476 | generalsupport@poly- tex.com

UNITED KINGDOM • IRELAND
01302-380775 | customer.serviceUK@palram.com

TOOLS & EQUIPMENT

Door Awning Sophia 1600 Grey Canopia-FIG2

SAFETY ADVICE

  • It is of utmost importance to assemble all of the parts according to the directions. Do not skip any steps.
  • We strongly recommend using work gloves during panel sliding.
  • Some parts may have sharp edges. Please be careful when handling components.
  • Always wear shoes and safety goggles when working with extruded aluminium.
  • If using a step ladder or power tools make sure that you follow the manufacturer’s safety advice.
  • Keep children away from the assembly area.
  • Do not touch overhead power cables with the aluminium profiles.
  • Do not attempt to assemble the product in windy or wet conditions.
  • Dispose of all plastic bags. Keep them out of reach of small children.
  • Do not climb or stand the roof.
  • Do not hang or lay the profiles.
  • Do not position your product in an area exposed to excessive winds.
  • Do not attempt to assemble this product if you are tired, have taken drugs or alcohol or if you are prone to dizzy spells.
  • Make sure there are no hidden pipes or cables in the wall before inserting the pegs.
  • This product is designed to be used mainly as a Door Awning.
  • Heavy snow load on the roof can make it unsafe to stand below or nearby.
  • The wall anchoring kit supplied with this product is suitable for concrete or solidbrick walls. Other wall types need an accordant wall fixation kit.

BEFORE ASSEMBLY

  • Selecting a site:
    • Choose your site carefully before beginning assembly.
    • Consider the door’s opening – inside or outside.
    • The product must be positioned and fixed on a flat level surface.
  • This is a multi-part assembly best achieved by two people. Allow at least half a day for the assembly process.
  • Take all components & parts out of the packages. Sort the parts and check against the content parts list.
  • Parts should be laid out close at hand. Keep all small parts (screws etc.) in a bowl so they do not get lost.
  • Please note multi-sided profiles are used in this Door Awning. As a result some holes in the profiles are not used during assembly.
  • Please review entire instructions before starting. Carry out the assembly steps in exact order.
  • Please consult your local authorities if any permits are required prior to constructing the product.

IMPORTANT!

  • During assembly use a soft surface below the parts to avoid scratches and damages.
  • You are solely responsible for determining whether the handling, storage, assembly, installation or use of this product is safe and appropriate in any location or for any given application.
  • The manufacturer is not responsible for any damages or injury to you, any other person or any property resulting from the improper handling, storage, installation, assembly or use of this product, or the failure to follow the manufacturer’s written instructions regarding the handling, storage, installation, assembly and use of this product.
  • This product is intended for normal residential use only. Do not use this product for any application that is not recommended in these instructions or building codes in effect in location where this product will be used. Always take care and use appropriate safety equipment (including eye protection) when assembling or installing this product.
  •  We recommend checking for restrictions or covenants for building this product in your area.
    In addition we advise to check if you need to submit any forms or if any permit is required prior to building the product.

DURING ASSEMBLY

During assembly, you will encounter different icons for different products. Please see below for more information:

  • You may use silicone lubricant spray on the frame in order to help you slide the panels into the profiles. Do not spray the panels.

  • Use a rubber mallet if necessary.

  • Make sure you remove covering plastic film from both sides of the panel.

  • All panels with the stamped words “THIS SIDE OUT” must be facing out to create full UV protection. Remove plastic sticker as panels are locked in place.

  • Steps marked with dashed outlines refer to Extensions only. Some of the steps are irrelevant for an assembly of a single product. When assembling a single or an extended product, some parts may be surplus.

  • These 2 icons below indicate if screw’s tightening is required or not. Temporary tightening of a few screws may be needed to prevent a profile from sliding out.
    Tighten all screws once assembly is completed.

CARE & MAINTENANCE

  • When your product needs to be cleaned, use a mild detergent solution and rinse with cold clean water.
  • DO NOT use acetone, abrasive cleaners or other special detergents to clean the panels.
  • Clean the product once assembly is complete.

IMPORTANT ASSEMBLY STEPS
When encountering this information icon during assembly, please refer the relevant assembly step for important additional comments.

  • Before inserting panels and locking in place, make sure you Remove covering plastic film from both sides of the panel.
  • In order to insert the panel, push it from the below.
  • Use scissors to cut the rubber gasket surplus.
  • Assemble the rubber gasket at the bottom of the product.
  • Assemble the rubber gasket above the panel at the top of the product.

Contents

Door Awning Sophia 1600 Grey Canopia-FIG5

INSTALLATION

Door Awning Sophia 1600 Grey Canopia-FIG6 Door
Awning Sophia 1600 Grey Canopia-FIG7 Door
Awning Sophia 1600 Grey Canopia-FIG8 Door
Awning Sophia 1600 Grey Canopia-FIG9 Door
Awning Sophia 1600 Grey Canopia-FIG10

3 YEAR LIMITED WARRANTY

PALRAM – CANOPIA | 3 YEAR LIMITED WARRANTY
Palram Canopia Ltd. (Company number: 512106824) whose registered office is at Teradion Industrial Park, M.P Misgav 2017400, Israel (“Canopia”) warrants that the product will be free from defects in material or workmanship for a period of 3 years from the original date of purchase.

  • This warranty is valid only if the product is installed, handled, cleaned, and maintained in accordance with Canopia’s written specifications.
  • This warranty does not cover defects resulting from normal wear and tear including, but not limited to: damage caused by use of force, incorrect handling, inappropriate use, negligence, accidents, impact from foreign objects, vandalism, pollutants, alteration, painting, damage resulting from cleaning with incompatible detergents or minor deviations of the product.
  • This warranty does not apply to damage resulting from “acts of Nature”, which includes but is not limited to hail, storm, tornado, hurricane, blizzard, flood, or fire.
  • Upon submitting proof of purchase and evidence of the claimed product failure, and subject to reporting the failure in writing within 30 days after discovery of the defect, Canopia, at its sole discretion, will replace defective parts of the Product, or refund you a prorated portion of the purchase price on a straight-line depreciated basis for the length of the warranty.

Palram Canopia Ltd.
Teradion Industrial Park, M.P Misgav 2017400, P.O.B 53, Israel Tel +972.4.848.6900 I Fax +972.4.848.6901
canopia@palram.com I www.canopia.com

Declaration of Performance

According to Construction Products Council Directive UE N ° 305/2011 and EN 14963:2006 Issue Date 01/01/2022

  1. Identification code: Bremen™ 1500/2050, refer to CE label no 070
  2. Type: A light transmitting self-supporting solid PMMA roofing structure with upstand made of galvanized steel elements
  3. Intended use: open multi-purpose covering
  4. Manufacturer: Pal ram Canopia Ltd. Teradion Industrial Park, M.P Misgav 2017400, P.O.B. 53, Israel
  5. Importer and EU representative : PALRAM Applications UK, Unit 40 )3 Industrial Estate Carr Hill, Doncaster DN4 SOE
  6. Assessment and verification of constancy of performance: System 3
  7. Declared performance:

Door Awning Sophia 1600 Grey Canopia-FIG11

The performance of the product identified in points 1 and 2 is in conformity with the declared performance in point 7.
This declaration of performance is issued, in accordance with Annex ZA.2.2 – EN 14963:2006, under the sole responsibility of Pal ram Canopia Ltd.
ITT reports and Factory Production Control records are available upon request at www.canopia.com

Signed for and behalf of Pal ram Canopia Ltd. by:
Teradion Industrial Park, Misgav, 01/01/2022

References

Read User Manual Online (PDF format)

Loading......

Download This Manual (PDF format)

Download this manual  >>

Related Manuals