LOREX E910AB 4K+ 12MP Ultra HD Smart Security Camera User Guide

Quick Start Guide
E910 Series
lorex.com

Safety Precautions

• Follow all instructions for safe use and handling of the product.
• Use the camera within given temperature, humidity and voltage levels noted in the camera specifications.
• Do not disassemble the camera.
• Do not point the camera directly at the sun or a source of intense light.
• Periodic cleaning may be required. Use a damp cloth only. Do not use any harsh, chemical-based cleaners.
• The supplied cable is rated for surface mounting only (Non-UL). Cables for in-wall and floor-to-floor installations are sold separately (CMR type). These and other cables are available at lorex.com.
• It is recommended to connect the camera to the NVR or an external PoE switch. If using a power adapter with this camera, a REGULATED power supply is REQUIRED (not included). Use of a non-regulated, non-conforming power supply can damage this product and voids the warranty.

Disclaimers

• Use the camera only with compatible Lorex recorders. For a full list, visit lorex.com/compatibility.
• Not intended for submersion in water. Installation in a sheltered location recommended.
• This camera includes an Auto Mechanical IR Cut Filter. When the camera changes between Day/Night viewing modes, an audible clicking noise may be heard from the camera. This clicking is normal, and indicates that the camera filter is working.
• Audio recording and/or face recording without consent is illegal in certain jurisdictions. Lorex Corporation assumes no liability for use of its products that does not conform with local laws.

What’s included

E910AB

| 4K+ Bullet Camera
---|---
| Mounting Kit
| Ethernet Extension Cable with Pre-attached Weather-resistant Cap

E910DD

| 4K+ Dome Camera
---|---
| Mounting Kit
| Ethernet Extension Cable with Pre-attached Weather-resistant Cap

*Per camera in multi-camera packages.

Overview

E910AB

1. Cable Notch
2. Adjustment Screw
3. Speaker
4. MicroSD Card Slot
5. Reset Button
6. IR (Infrared) Light
7. Camera Lens
8. Smart Security Lighting
9. Warning Lights
10. Microphone

E910DD

1. Adjustment Screw
2. Smart Security Lighting
3. Microphone
4. IR (Infrared) Light
5. Reset Button
6. Speaker
7. Camera Lens
8. Warning Lights
9. Cable Notch
10. MicroSD Card Slot

Camera Placement Tips

• Install the camera in a location that is difficult for thieves and vandals to reach.
• Secure cabling so that it is not exposed or easily cut.
• Point the camera where there is the least amount of obstructions (i.e. tree branches).
• Take into consideration what you want to monitor and where is the best coverage area.
• Place your camera close to the area of interest.
• The best position is 10 ft (3 m) above ground, angled 15° down.

Mounting Your Camera

Test your camera prior to selecting a permanent mounting location, see page 14.

1. Use the mounting template to drill holes for screws, then insert the drywall anchors. Drill a hole for the camera’s cable if you plan to run it through the mounting surface.

2. Use the screws to mount the camera base to the surface. If you are running cables along a wall/ceiling, make sure to pass the cable through the cable notch.

3. Feed the camera’s cable through the camera base, then connect the cables (see page 14).

4. Loosen the adjustment screw and position your camera as needed, then tighten to secure it in place.

5. Remove the vinyl film from the camera lens once your installation is complete.

6. Use the mounting template to drill holes for screws, then insert the drywall anchors. Drill a hole for the camera’s cable if you plan to run it through the mounting surface.

7. Use the Allen key to loosen the camera’s adjustment screw, then remove the dome cover from the camera base.

8. Use the screws to mount the camera base to the surface. If you are running cables along a wall/ceiling, make sure to pass the cable through the cable notch.

9. Feed the camera’s cable through the camera base, then connect the cables (see page 14).

10. Angle your dome camera, then use the Allen key to tighten the dome cover firmly onto the camera base.

11. Remove the vinyl film from the camera lens once your installation is complete.

Connecting Your Camera

Connect your camera directly to your recorder using the camera’s Ethernet extension cable.

Weather-resistant Cap

To use the weather-resistant cap: Twist the cap securely onto your camera’s Ethernet connector.
The pre-attached weather-resistant cap covers both the camera’s Ethernet connector and the Ethernet extension plug to provide protection from weather, dust, dirt and other environmental contaminants. If exposed to regular precipitation, seal the cap with silicone and electrical tape for additional sealing.

Cable Extension Options

For different UL CMR approved cable lengths, visit lorex.com and search for the specified cable type in the table.

Need Help?

For related support, scan the QR code or visit:

help.lorex.com/E910ABhelp.lorex.com/E910DD

Register Your Product

Please see our full Terms of Service and Limited Hardware Warranty Policy at: lorex.com/warranty

Copyright © 2023 Lorex Technology Inc.
As our products are subject to continuous improvement, Lorex reserves the right to modify product design, specifications and prices, without notice and without incurring any obligation. E&OE. All rights reserved.

E910-Series_QSG_EN-FR-ES_R1

References

• Security Cameras - Home Security Camera Systems | Lorex
• Product Compatibility Chart - Expand Your System | Lorex

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>