Yasir Electronics 250kg Commercial Ice Maker Instruction Manual

Yasir Electronics 250kg Commercial Ice Maker Instruction Manual

The picture is for reference only. Please be subject to the actual product. Please read the user manual carefully before using the appliance and keep it for future reference.

Email Address: icemaker@tazpi.com
Phone Number: 252-465-3438

IMPORTANT SAFETY REGULATIONS

When using electrical appliances, basic safety precautions should be followed to reduce the risk of fire, electric shock and injury to persons or property. Please read all instructions before operating the machine for the first time.

CAUTION: ICE CAN’T BE STORED IN THE ICE BIN DURING NIGHTTIME, IT’SNOTAFRIDGE, AND ICE WILL BE MELTED TO WATER AND GET OUT OF THE MACHINE

• The machine must be installed correctly according to the installation procedure before use.
• Do not place the power cord on carpet or other heat sources. Also, do not place the power coordinal area where people or objects are moving or immerse the power cord in water. The use of extension cords is not recommended because of the risk of overheating or fire.
• If the power cord is damaged, it must be replaced by the manufacturer, its service department or similarly qualified persons in order to avoid a hazard.
• Be sure to pull
• out the plug when the machine is no longer in use.
• Please pull out the plug or cut off the main power supply before cleaning or repairing the machine. Note: If the machine needs to be repaired, it is strongly recommended to be operated by professional.
• Never pull the power cord with your hand to pull out the plug, and you must hold the plugwithyour hand and pull it out in a straight line.
• Do not store explosives, such as combustion supporting spray, in the appliance; The appliance is intended for domestic and similar purposes, e.g.:
  • kitchen areas in shops, offices or other workplaces;
  • Guests in farms as well as hotels, motels and residential-type environments;
  • family hotel type environment;
  • Used in food and beverage industry and similar non-retail industries

Warning: Do not use the ice machine outdoors or expose it to rain. The ice machine shall be place dad used indoors free of obstructions, with good ventilation, and away from direct sunlight. Distance of 15 cm at least should be kept from the walls in the front, at left or at right to facilitate heat dissipation.

• Please do not tip or tilt the machine, as this may cause abnormal noise and ice cubes of abnormalize, and more serious may cause water leakage.
• If the machine has just been moved from the outdoors in winter, please turn it on after a period of time when the temperature of the machine rises.
• Do not use electrical appliances in the pantry of the appliance other than the type recommended by the manufacturer.

IMPORTANCE:

• The machine must be grounded and use a power supply of 120V ~/60Hz.
• Only connect to drinking water sources that comply with local drinking water standards.
• In addition to the methods recommended by the manufacturer, mechanical equipment or other means shall not be used to accelerate the defrosting process, and the refrigeration circuit shall note damaged.
• The refrigeration system contains high-pressure refrigerant, and the refrigeration system shall not be damaged. Special care must be taken during installation and handling. Installation and maintenance must be carried out by the manufacturer or professionals. Scrap must be disposed of by designated recycling departments.

WARNING:
RISK OF FIRE ！

The ice machine has thermal insulation materials, which are combustible materials and must be kept away from fire sources. Maintenance must be carried out by the manufacturer or professionals. Scrap must be disposed of by designated recycling departments.

The refrigerant used is R290 in this appliance. It is a highly flammable refrigerant. The foam blowing agent used is Cyclopentane in this appliance. They are highly flammable.

Thank you for selecting our Commercial Ice Maker. In order to protect your legitimate rights and interests, please pay attention to the following points when you receive the machine.

1. Due to the logistics delivery requirements of this ice machine, we divided the ice machine in to two express delivery packages, one for the ice bin and another for the main machine
2. The outer packing of the machine is intact.
3. Machine’s model is consistent with your purchase.
4. The appearance of the machine is in good condition.
5. The attached parts are complete. 6. The internal components of the machine are in good condition

Accessories List

Take the two accessories bags from the ice bin and check whether all the Belo accessories are included or not.

If any parts are missing, please contact our customer service

Email Address: icemaker@tazpi.com
Phone Number: 252-465-3438

filter, and 2pcs need to put inside of the connector of the drain hose, other 3pcs are spare.| 6PCS
11| Silicone gasket| | 1pc need to put inside of the connector of the filter, the other 1pc is spare.| 2PCS
12| Thread seal tape| | Sealing if necessary| 6PCSc
13| Screw| | ST5*18| 6PCS
14| Feet| | Screw fee before using the machine| 4PCS

Note: Items 5 and 6 had been assembled together before being packaged

Installation and Connection

Control Board

Operation Instruction

Plug in and turning on the switch on the back of the main machine will make the machine enter into standby mode; The screen will be locked automatically after not operating any button for 60seconds, hold any button for 3 seconds to unlock the screen. If the machine was power doff because of the abnormal shutdown, the machine will enter into ice-making mode automatically after restoring power.

ON/OFF Button:
When the unit is off, press this button to turn on the unit, and during the normal ice-makings Tate, hold this button for 2s to turn off the unit at once.

Turn on the machine, ice making and cleaning indicator will turn on, the machine will add water automatically; if it detects that the water is enough, the machine will enter the ice ma king state tera few seconds.

Mode Button:
When the mode button is touched in the power-on state, it can be adjusted with 3 modes manually and cycle through the three states of ice making, water pump( drain) and heat valve (forced deicing)in turn.

Clean and Setting Button:
In the power-on state, click the cleaning button to enter the cleaning state.

Adjust Ice-Making Time:
In the state of ice making or water inflow, touch “△” or “▽” to adjust the ice making time(scope of ice making time is -5 minutes to +8 minutes)

Reservation Button:
In the standby mode, click the reservation button to enter the reservation function, and the reservation time can be adjusted by pressing the “△” or “▽” button. In the standby state, press and hold the setting button for 5 seconds to enter the setting state;

Click the setting button to set the previous code, and cycle from 0 to in turn. Click “+” or “-”toadjust the last two digits. Please refer to the table below for each code number:

Table 1: Setting Reference Table

efficient
7| High voltage detection| 00/01| 00| “00”No high voltage detection； “01”      With high voltage detection| efficient
8| mode selection| 00/01| 01| “00”ice thickness mode； “01”timed mode| Not efficient-
9| Water-cooled and air-cooled| 00/01| 00| “00”air-cooled； “01”water-cooled| Not efficient-
| High temperature alarm| From 65 to 80℃| 70℃| Condensation probe high temperature alarm| efficient
| Manual cleaning time| From 2 to30minutes| 10minutes| | efficient
| Water intake method| 00/01| 00| “00”running water；“01”water bucket| efficient
| Drain time| 05-60S| 20seconds| Stepping for 5 seconds| efficient

Status Display:

1. Power On: The LCD is fully bright, and the four-digit number displays the version number.
2. Water Inlet: Time displays C00, ice making, deicing and full ice are light.
3. Thermal Valve: Cleaning, ice making, deicing and full ice are light.
4. Ice Making: When the ice making icon is on, the time displayed is the ice making time
5. Defrost: After the ice making process, the water pump is turned off, the defrost valves turned on, allowing the hot gas to enter the evaporator for about 1-2 minutes, the ice cubes slide from the evaporator into the ice bin. When the deicing icon is on, the time displayed is the deicing time.
6. Ice Full: In the running state, with the ice bin filled to a certain height, the ice sliding board cannot be rebounded or reset because of the block of the freshly produced ice cubes, the icemaker will stop. When the blocking ice cubes are taken away, the ice maker will turn back to icemaking process in a few seconds. When the ice full icon is on, the time displayed is theicefulltime.
7. Fault: The fault icon is flashing, and the corresponding fault Chinese characters are bright.
8. Shutdown: Display OFF.
9. Appointment Time Setting: The appointment icon is on, and the time is displayed as the scheduled power-on time.
10. Reservation Status: The reservation icon is flashing, showing the countdown of the reservation time.
11. Setting Status: The time display digital tube displays the setting parameter number on the forklift, which is always on. The last two digits or three digits are parameter values, which are lashing.

Installation Position

Note: first, screw the four foots supplied with the machine to the corresponding positions on the bottom of the machine.

• a) This series of machines shall be placed in a clean place with good air circulation. They shall note placed in the open air or exposed to sunlight or rain.
• b) The machine cannot be placed near any heat source.
• c) Around this series of machines, the ambient temperature should not be lower than 3°C(37.4°F)and not higher than 40°C (104°F) , and an appropriate distance should be kept so as to maximize the ice-making effect and heat dissipation of the machine
• c) The machine shall be placed on a stable level base or the ground. Please calibrate the levels of the front left and the front right directions during the installation.
• d) Please do not place any objects on the top of the ice machine.
• e) The enough space must be remained on the left and the right sides and the back so as to maintain good air intake and facilitate the maintenance

Setting

Improper installation may cause injury to people or objects. Please place the ice machine at a constant location where the power cord can be directly lugged in to the socket.

Electrical Connection
Warning: this machine must be grounded

• a) There must be a power supply or socket that can provide 120V ~/60Hz, and the power supply or socket must be reliably grounded.
• b) The fusing current of the electrical box must be greater than 20A. If it needs to be replaced, it must be done by professionals.
• c) If the power cord or plug needs to be replaced, it must be done by a professional after-sales service engineer.
• d) The voltage fluctuation shall not exceed ±10% of the rated voltage, otherwise a voltage stabilizer shall be installed

Water Supply and Drainage Connections

Warning: the ice machine should only be connected to a drinking water source and the watercourses must meet the local drinking water standard.

• – The water supplied to the ice machine must be connected with a filter to improve the drinking standard of the water. Please do not connect to the tap water directly. If the ice ma king fault is caused by the tap water, our company will not be responsible for the maintenance.
• The water supply pressure should be 0.1-0.4MPa. If the pressure is greater than0.4MPa, pressure reducing valve should be connected. Please use the new hose assembly attached other appliance. The old hose assembly cannot be reused
• As the water is drained through the dead weight of water, the drain pipe should have sufficient height or drop.

1. Remove the plug on the water inlet connector on the back of the machine, insert the water interline into the water inlet connector, and clamp the blue card into the slot of the water inlet connector to ensure no water leakage.
2. Connect the other end of the external inlet pipe to the tap.

Method for Disassembling and Assembling the Plug and the Water Inlet Pipe

Ice machine pre-filter Installation diagram

Installation and Connection

WARNING: The machine must stand for 24h before power on.

Install the machine according to the manual.

Unpack the Main Machine and Ice Bin

Note: Installation must be carried out by a professional according to the instruction manual. Warning: Please do not use foam and other packaging materials as toys for children andmentallyhandicapped people, because it may bring them danger.

Note: Please remove all packing parts when using, otherwise the machine may not worknormally.

First, take the main machine and ice bin from carton

Second, place the main machine on the top of the ice bin as the illustration.

Installation of Pre-filter

Operation in Struct ion

Warning:

This ice machine is used to manufacture and store ice for use, and in order to ensure the hygiene of the ice, please follow the following principles:

• Wash your hands before taking out ice cubes, and use the plastic ice scoop provided in the accessories to take the ice.
• Do not store anything other than ice cubes in the storage bin.
• Clean the storage bin before use. Keep the ice scoop clean and rinse with a neutral detergent. After removing the ice, close the door to prevent dust from entering.

The use of any electrical appliance should follow the basic guidelines, in particular:

• The environment with high humidity will increase the risk of a short circuit or electric shock, if indebt, please cut off the power of the ice machine.
• Please do not directly pull down the power cord to shut down the machine.
• The ice machine cannot be used by children or the elderly without adult supervision.

1. Operation
   The installation service personnel are usually authorized to start the automatic icemaking program. For smooth ice making, the following points need to be confirmed:
   a) Opening of water supply taps;
   b) The lower drain has been connected to the drain of the room;
   c) The ice machine is connected to the power supply;

2. Prepare the long-term preservation for the ice machine
   a) Unplug the power plug or cut off the power supply;
   b) Close the water supply tap and remove the water inlet pipe;
   c) Remove all ice and drain the storage bin and water tank;
   d) Wash and dry the inner walls of the storage bin and water tank

Cleaning & Maintenance

Warning: Do not use any alcohol or fume for cleaning/sanitization of the ice machine. It maycausecracks on the plastic parts. Ask a trained service person to check and clean the condenser at least once a year, in order to let the unit work properly. This appliance must be cleaned by use water jet.

CAUTION: If the ice machine has been left unused for a long time, before the next use it must be thoroughly cleaned. Follow carefully any instructions provided for cleaning or use of sanitizing solution.

• Do not leave any solution inside the ice machine after cleaning.
• Periodic cleaning and proper maintenance will ensure efficiency, top performance, hygienic, angling life. The maintenance intervals listed are based on normal conditions. You may want to shorten the intervals if you have pets, or there are other special considerations.

What Shouldn’t Be Done
Never keep anything in the ice storage bin that is not ice: objects like wine and beer bottles  unsanitary but also their labels may slip off and obstruct the drain pipe

Exterior Cleaning
The door may be cleaned with a mild detergent and warm water. Do not use solvent-based or abrasive cleaners. Use a soft sponge and rinse with clean water. Wipe dry with a soft clean towel to prevent water spotting.

NOTE: Stainless steel models exposed to chlorine gas and moisture, such as in areas with spacers swimming pools, may have some discoloration of stainless steel. Discoloration from chloral inegasisn formal.

Interior Cleaning
For Ice Storage Bin

The ice storage bin should be sanitized occasionally. Clean the bin before the ice ma chine soused for the first time and reused after stopping for an extended period of time. It is usually convenient to sanitize the bin after the outside, the storage bin must be empty

1. Disconnect power to the unit.
2. Open the door ad with a clean cloth, wipe down the interior with a sanitizing solutionmadeof28g of household bleach or chlorine and 7.5L of hot water.
3. Rinse thoroughly with clear water. The waste water will be drained out though the drainpipe.
4. Reconnect power to the unit.
5. The ice scoop should be washed regularly. Wash it just like any other food container

WARNING: Do not use solvent-based or abrasive cleaners. These may transmit taste to the ice cubes.

Cleaning Suggestion

1. DAYLY CLEANING
   The ice spoon, door and the water dividing pipe should be cleaned by yourself per eachday. At theend of every day, rinse the ice spoon and wipe the both sides of the door with a clean cloth.

2. SEMI-MONTHLY CLEANING
   The ice bin, water tank, the ice-full detecting plate and the surface of the evaporator aretobecleaned by yourself semi-monthly according to interior cleaning program.

3. QUARTERLY CLEANING
   All the components and surfaces exposed to water or ice cubes, like ice storage bin, water tank, door, evaporator, water pump, water dividing pipe, etc. should be cleaned 3 months according to the following steps:

a. Disassemble the front panel
b. Add water and vinegar or lemon juice mix (1:1 ratio) or other similar acid detergent into the water tank. c. Press “Clean” icon to make the machine enter self-clean mode, this progress takes about 10minutes. When the Self- clean program is finished, drain off any remaining water.

NOTE: It is strongly recommended to clean the unit before initial use or after the unit has not benign use for a long period of time.

Trouble Shooting

No Ice Making

Fault phenomenon| **Inspection items| ****Possible causes| ****Solutions
---|---|---|---
Ice machine is not running| Power cord| Not plugged in the socket| Plugged in the socket
Control panel fuse| Fused or damaged| Check and replace.
** Storage bin| The ice is full, and the ice cubes press the evaporator to swing the blades| Remove ice cubes or remove ice from evaporator swing vanes
**** Power supply| If there is no such situation, the proximity switch is faulty| Replace the proximity switch
No power or low voltage| Contact the power supply department
Water supply tap| No water or low water pressure| Increase water pressure
Inlet valve| The filter screen is blocked or the inlet valve is broken| Clean the filter or replace the inlet valve
The compressor does not run or stops suddenly| Power supply| 1. The voltage is too low.| Contact the power supply department
Air inlet| The air inlet is blocked| Leave a space of at least 15 cm on the left, right and rear sides
Condenser| Excessive ash deposit| Clean condenser
Cooling system| Refrigeration system leakage| Contact after-sales service personnel
Compressor| The connecting wire is broken or falls off| Contact after- sales service personnel
No water in water tank| Floating ball| Floating ball is stuck or clogged| Replace or clean the floating ball
Water leakage| Inlet| Loose or improperly installed| Tighten or reinstall
Inlet or drain| Water leakage due to rupture| Change
Ice making time is too long| Water pressure ofwater supply| The water pressure is too low, and the water supply time is toolong each time| Increase water pressure
Water temperature| Water temperature too high| Lower water temperature
Ambient temperature| The ambient temperature is too high or too low| Place at an appropriate temperature
Refrigerant| The refrigerant leaks| Contact after-sales service personnel
Little or thin ice| Condenser| Excessive dust accumulation in the condenser leads to poor air intake, high condensation temperature, and long ice making time|

Clean condenser

Filter screen| The filter screen is blocked, causing poor water flow| Clean or replace the filter screen
Water pump| Poor water flow due to water pump failure| Replace water pump
Ambient temperature| Ambient temperature too high| Place at a lower temperature
|  Air inlet| Poor air intake leads to high condensation temperature andlong ice making time| Leave a space of at least 15 cm on the left, right andrear sides

Circuit Diagram

After Sale Service

1. If your product breaks down or has any problems after purchase, please contact us, you can always contact our customer service by email at icemaker@tazpi.com
2. Regarding any product problems or issues you encounter, our customer service will guide you through the entire service process. We reserves the right to re-inspect damaged or returned products.

If you have any warranty  questions, please contact us at

Email Address: icemaker@tazpi.com
Phone Number: 252-465-3438

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>