LUUCCO ProTalker S1 2.4GHz Digital Wireless Microphone User Manual

LUUCCO ProTalker S1 2.4GHz Digital Wireless Microphone

Packing List

Product Structure

Charging Case

• Indicator

When the case is charging: Flashing

When the case is un-charging

1. Charging case indicator
2. TX1 indicator
3. RX indicator
4. TX2 indicator

Transmitter

fast

LED Indicator

Power/Pair button

Long press

Power OFF
Pair| Short press twice

TX can’t be used when charging

Mute button

1. Noise cancellation button
2. Built-in Microphone
3. USB-C Charging Port

Receiver

LED Indicator

TX2 flashing blue

TX1 disconnected, TX2 connected| TX1 flashing blue,

TX2 static blue light

Low battery| Less than 30%: Flashing red slowly Less than 10%: Flashing red fast

Type-C Connector

•  It can be connected to an Android Smartphone, Tablet, Computer, and other Type-C devices.
• Most Type-C devices can be powered and charged through this port while in use.

Power/Pair button

Long press

Power OFF
Pair| Short press twice

• Gain control (+/-) / M/S button
• Short press the + or – button to adjust mic gain (total 6 levels).
• Short press the + and – buttons simultaneously to adjust Mono or Stereo.

USB-C Charging Port

Operation Guide

1. The TX and RX automatically turn on or off when they are taken out of or put back in and close the charging case.
2. Mount the TX to your coat.

Connect the RX to a mobile phone.

RX supports live monitoring
Charge the mobile phone via the RX.

Connect with a Camera

Manual Pairing
Before leaving the factory, the TX and RX have been paired with each other. If they are disconnected, please follow the below steps

1. Short press the button on the RX twice, and the LED light flashes blue fast.
2. Short press the button on the RX TX twice
3. If the indicators of TX and RX are static blue, they are paired. Otherwise, please try the above steps again

Specifications

Frequency Range: 50Hz-20kHz
Sensitivity| -32dB±1.5dB @ 1KHz
Operation Range| 250m (820ft) (Line of Sight)
Signal-to-Noise Ratio| >80dB
Maximum SPL| 110dB SPL
Overall Power Consumption| 3.7V/30mA
Bit Depth| 16 bit
Sampling Rate| 48 kHz

Battery Capacity

| RX: 190 mAh
TX: 190 mAh
Charging Case: 1000 mAh

Operating Time

| RX: 8H
TX: 8H
Charging Case: Appr. 1.5 time charging for 2 TX and 1 RX

Charging Time

| RX: 2H
TX: 2H
Charging Case: 2.5H

Dimensions

| RX: 5.2 x 2.9 x 1.1 cm (2 x 1.1 x 0.4 “)
TX: 5.2 x 2.1 x 1.8 cm (2 x 0.8 x 0.7 “)
Charging Case: 7.9 x 3.1 x 6.2 cm (3.1 x 1.2 x 2.4 “)

Weight

| RX: 11.2g (0.4 oz)
TX: 12.4g (0.44 oz)
Charging Case: 85.8g (3 oz)

WARNING

1. Read and understand the user manual completely before using the product.
2. The Mic contains magnets. Keep it away from mag cards, IC cards, hard disks, RAM chips, implantable medical devices, and other devices to avoid interference.
3. DO NOT listen at a high volume for an extended period using monitor earphones. Otherwise, you may experience possible hearing damage.
4. DO NOT allow the product to come into contact with any kind of liquid. DO NOT leave the product out in the rain or near a source of moisture. DO NOT drop the product into water.
5. The product should be used in temperatures from -10 to 45° C (14° to 113° F). Use of the product in environments above 45°C (113° F) can lead to a fire or explosion. Use of the product below -10° C (14° F) can lead to permanent damage.
6. Never disassemble or pierce the product in any way or the battery may leak, catch fire, or explode.
7. DO NOT leave a battery in an extremely high temperature surrounding environment, it can result in an explosion or the leakage of flammable liquid or gas.
8. DO NOT store the product fully discharged for an extended period. Otherwise, it will over-discharge, which will lead to permanent damage.
9. Battery cannot be subjected to high or low extreme temperatures, or low air pressure at high altitudes during use, storage, or transportation.

FCC Statement

FCC Requirement
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause undesired operation.

Warning
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

NOTE
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

RF warning statement
The device has been evaluated to meet general RF exposure requirements. The device can be used in portable exposure conditions without restriction.

Manufacturer: Luucco (Shenzhen) Technology Co., Ltd. Factory Add.: No. 13/14, Building 9, Huake City Incubation Park
Daojiao Town, Dongguan City, Guangdong， China Email: sales@luuccotech.com www.luuccotech.com

References

• LUUCCO – Luucco wonderful moments!

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>