SIGNATURE HARDWARE 484490 Marylew 3 Light 16 Wide Outdoor Taper Candle Pendant Instruction Manual

: June 13, 2024
: Signature Hardware

Table of Contents

BEFORE YOU BEGIN
GETTING STARTED
FOR YOUR SAFETY
CARE INSTRUCTIONS
INSTALLATION (FIG. 1)
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

MARYLEW
SKU: 953855

BEFORE YOU BEGIN

We recommend consulting a professional if you are unfamiliar with installing electric fixtures. Signature Hardware accepts no liability for any damage to the property, the product or for personal injury during installation. Observe all local electrical building codes.
Unpack and inspect the product for shipping damage.
If any damage is found, contact our Customer Relations team via live chat at www.signaturehardware.com or by emailing support@signaturehardware.com.

GETTING STARTED

Ensure that you have gathered all the required materials that are needed for the installation.

FOR YOUR SAFETY

WARNING: Be sure the electricity to the wires you are working on is shut off, either the fuse is removed or the circuit breaker is shut off. You don’t need special tools to install this fixture. Be sure to follow the steps in the order given. Under no circumstances should a fixture be hung on house electrical wires, nor should a swag type fixture be installed on a ceiling which contains a radiant type heating system. Read instructions carefully, if you are unclear as to how to proceed, consult a qualified electircian.

CARE INSTRUCTIONS

To clean, wipe fixture with a soft cloth. Clean glass with a mild soap. Do not use abrasive materials such as scouring pads or powders, steel wool or abrasive paper.

TOOLS AND MATERIALS:

| | |
---|---|---|---
Safety goggle| Step ladder| Wire strippers| Wire cutters
| | |
Phillips screwdriver| Flathead screwdriver| Electrical tape| Light Bulb
(E12 60 watt maximum)

INSTALLATION (FIG. 1)

Push fixture wires up through bottom of loop (M).
Pull fixture wires taut. Screw loop (M) onto top of fixture body (O).
Connect one locking link (G) to loop (M).
Determine desired hanging height of fixture. Cut chain (H) to length to achieve desired height.
Slip chain link at end of chain (H) onto locking link (G) on loop (M).
Weave fixture wires through chain links, skipping every other chain link.
Push fixture wires through hole in canopy.
Attach locking link (G) to last link on chain (H) and to loop on canopy (D).
INSTALLATION (FIG. 2)
Carefully pull house wires down out of junction box so house wires are easily accessible to connect fixture wires.
Position mounting bracket (A) so threaded ends of attached fixture mounting screws (E) are facing down towards floor.
Carefully pull house wires through center hole in mounting bracket (A).
Align holes in mounting bracket (A) with holes in junction box. Thread junction box screws (B) into holes in mounting bracket (A) and into holes in junction box.
Tighten junction box screws (B) to secure mounting bracket (A) to junction box.
INSTALLATION (FIG. 3) Connect Black or Red Supply Wire (Lead Wire) to:| Connect White Supply Wire (Neutral Wire) to:
---|---
Black wire| White wire
Parallel wire (round or smooth)| Parallel wire (square or ridged)
Clear, brown, gold or black wire without tracer| Clear, brown, gold or black wire with tracer
Insulated wire (other than green) with copper conductor| Insulated wire (other than green) with silver conductor

When parallel wires are used, the neutral wire is ridged down its length and the other wire is round and smooth (see illus.).
1. Strip 3/4” of insulation from ends of fixture wires.
2. Twist the end of fixture white wire to the end of house white wire together. Twist a wire nut onto ends of wires. Wrap electrical tape around wire nut and wires to secure connection. Twist the end of fixture black wire and the end of house black wire together. Twist a wire nut onto the ends of wires. Wrap electrical tape around wire nut and wires to secure connection.
  Loosen ground screw on mounting bracket (A). Wrap house ground wire around ground screw leaving enough ground wire to attach to fixture ground wire. Twist the end of fixture ground wire to the end of house ground wire together. Twist a wire nut onto ends of wires. Wrap electrical tape around wire nut and wires to secure connection.
  NOTE: If you have electrical questions consult your local electrical code for approved grounding methods.
3. After wires are connected, carefully tuck wires inside junction box.
  INSTALLATION (FIG. 4)
4. Carefully raise �xture up to ceiling. Place canopy (D) over mounting bracket (A). Pass holes in canopy (D) over ends of �xture mounting screws (E).
5. Screw one threaded cap (F) onto each fixture mounting screw (E). Tighten threaded caps (F) to secure fixture to ceiling. DO NOT over tighten.
6. Ensure clips along top inside of cage (O) are pressed upward to allow glass panels (K) to fit behind clips.
7. Carefully place one glass panel (K) inside cage. Set bottom edge of glass panel (K) into channel along bottom of one side of cage. Carefully push glass panel (K) against side of cage. Fit top edge of glass panel (K) behind clip along top edge of side of cage. Carefully press clip down against glass panel (K) to hold glass panel (K) in place. Repeat this step for remaining glass panels (K).
8. Screw recommended bulbs (E12 candelabra bulb type, not included) into sockets. Verify correct bulb wattage marked on socket of fixture. WARNING: DO NOT exceed maximum bulb wattage.