Signature Hardware 953852 CAVIANA Brushed Nickel Caviana 10 Inch Wide Pendant Instructions

: June 13, 2024
: Signature Hardware

Table of Contents

Signature Hardware 953852 CAVIANA Brushed Nickel Caviana 10 Inch Wide
Product Usage Instructions
BEFORE YOU BEGIN
GETTING STARTED
- FOR YOUR SAFETY
CARE INSTRUCTIONS
INSTALLATION
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

Signature Hardware 953852 CAVIANA Brushed Nickel Caviana 10 Inch Wide

Pendant

Product Information

Product Name: CAVIANA Pendant Luminaire Suspendu Colgante
SKU: 953852

Before You Begin
We recommend consulting a professional if you are unfamiliar with installing electric fixtures. Signature Hardware accepts no liability for any damage to the property, the product, or for personal injury during installation. Observe all local electrical building codes.

Unpack and inspect the product for shipping damage. If any damage is found, contact our Customer Relations team via live chat at www.signaturehardware.com or by emailing support@signaturehardware.com.

Getting Started
Ensure that you have gathered all the required materials that are needed for the installation.

Care Instructions
To clean, wipe fixture with a soft cloth. Clean glass with a mild soap. Do not use abrasive materials such as scouring pads or powders, steel wool, or abrasive paper.

Additional Questions?

Still need help? Check out our Help Center at www.signaturehardware.com
for product and warranty information, or contact us through live chat or by emailing support@signaturehardware.com.

Product Usage Instructions

IMPORTANT: At least one 6 inch stem must be used. Carefully push fixture wires up through the bottom of the 6 inch stem (N).
Pull fixture wires out of the top of the stem (N) and pull them taut. Screw the bottom of the stem (N) onto the top of the fixture body (O).
Determine the desired hanging height of the fixture. Select the quantity of stems (M) to achieve that height.
Carefully push fixture wires through the remaining stems (M).
Thread the stems (M) together carefully, keeping the fixture wires taut.
From the last stem (M), push fixture wires up through the swivel (S) attached to the canopy (D). Carefully pull fixture wires up through the canopy (D) and keep them pulled taut.
Position the mounting bracket (A) so that the threaded ends of the attached fixture mounting screws (E) are facing down towards the floor.
Align the holes in the mounting bracket (A) with the holes in the junction box.
Thread each junction box screw (B) into each hole in the mounting bracket (A) and into the holes in the junction box.
Tighten the junction box screws (B) to secure the mounting bracket (A) to the junction box.

Note: Please refer to the provided diagrams and illustrations in the user manual for a visual representation of the installation steps.

BEFORE YOU BEGIN

We recommend consulting a professional if you are unfamiliar with installing electric fixtures. Signature Hardware accepts no liability for any damage to the property, the product or for personal injury during installation. Observe all local electrical building codes.
Unpack and inspect the product for shipping damage. If any damage is found, contact our Customer Relations team via live chat at www.signaturehard- ware.com or by emailing support @signaturehard-ware.com.

GETTING STARTED

Ensure that you have gathered all the required materials that are needed for the installation.

FOR YOUR SAFETY

WARNING: Be sure the electricity to the wires you are working on is shut off, either the fuse is removed or the circuit breaker is shut off. You don’t need special tools to install this fixture. Be sure to follow the steps in the order given. Under no circumstances should a fixture be hung on house electrical wires, nor should a swag type fixture be installed on a ceiling which contains a radiant type heating system. Read instruc-tions carefully, if you are unclear as to how to proceed, consult a qualified electrician.

CARE INSTRUCTIONS

To clean, wipe fixture with a soft cloth. Clean glass with a mild soap. Do not use abrasive materials such as scouring pads or powders, steel wool or abrasive paper.

TOOLS AND MATERIALS:

INSTALLATION

(FIG. 1)

IMPORTANT: At least one 6 inch stem must be used.

Carefully push fixture wires up through bottom of 6 inch stem (N). Pull fixture wires out of top of stem (N). Pull fixture wires taut. Screw bottom of stem (N) onto top of fixture body (O).
Determine desired hanging height of fixture. Select the quantity of stems (M) to achieve that height.
Carefully push fixture wires through remaining stems (M). Thread stems (M) together carefully keeping fixture wires taut.
From last stem (M), push fixture wires up through swivel (S) attached to canopy (D). Carefully pull fixture wires up through canopy (D). Keep fixture wires pulled taut.
Screw last stem (M) to swivel (S) on canopy (D).
(FIG. 2)
Carefully pull house wires down out of junction box so house wires are easily accessible to connect fixture wires.
Position mounting bracket (A) so threaded ends of attached fixture mounting screws (E) are facing down towards floor.
Align holes in mounting bracket (A) with holes in junction box.
Thread each junction box screw (B) into each hole in mounting bracket (A) and into holes in junction box. Tighten junction box screws (B) to secure mounting bracket (A) to junction box.
(FIG. 3)** Connect Black or Red Supply Wire (Lead Wire) to:| Connect White Supply Wire (Neutral Wire) to:*
---|---
Black wire| White wire
Parallel wire (round or smooth)| *Parallel wire (square or ridged)
Clear, brown, gold or black wire without tracer| Clear, brown, gold or black wire with tracer
Insulated wire (other than green) with copper conductor| Insulated wire (other than green) with silver conductor

When parallel wires are used, the neutral wire is ridged down its length and the other wire is round and smooth (see illus.).
1. Strip 3/4” of insulation from ends of fixture wires.
2. Twist the end of fixture white wire to the end of house white wire together. Twist a wire nut onto ends of wires. Wrap electrical tape around wire nut and wires to secure connection. Twist the end of fixture black wire and the end of house black wire together. Twist a wire nut onto the ends of wires. Wrap electrical tape around wire nut and wires to secure connection. Loosen ground screw on mounting bracket (A). Wrap house ground wire around ground screw leaving enough ground wire to attach to fixture ground wire. Twist the end of fixture ground wire to the end of house ground wire together. Twist a wire nut onto ends of wires. Wrap electrical tape around wire nut and wires to secure connection.
  NOTE: If you have electrical questions consult your local electrical code for approved grounding methods.
3. After wires are connected, carefully tuck wires inside junction box.
  (FIG. 4)
4. Carefully raise fixture up to ceiling. Place canopy (D) over mounting bracket (A). Pass holes in canopy (D) over ends of fixture mounting screws (E).
5. Screw one threaded cap (F) onto each fixture mounting screw (E). Tighten threaded caps (F) to secure fixture to ceiling. DO NOT over tighten.
6. Screw recommended bulb (E26 Edison bulb type, not included) into socket. Verify correct bulb wattage marked on socket of fixture. WARNING: DO NOT exceed maximum bulb wattage.