KeTeR MANOR Pent 6×6 User Manual
- June 4, 2024
- Keter
Table of Contents
MANOR Pent 6×6
User Manual
US, Canada
Tel: +1877-638-7056, NACS@keter.com
Mon – Fri | 8am – 6pm ET / Lundi-Vendredi 8h -18h
Sat – Sun | 9am – 6pm ET / Samedi-Dimanche 9h-18hUK
Tel: +44-121-506-0008, CSUK@keter.com
Mon – Fri | 8:30am – 5pm
For other European countries see the last page
WARRANTY ACTIVATION
Thank you for your purchase of the Keter shed. In order to activate your
warranty, please log onto our website and fill in the form under warranty
activation. keter.com/en/warrant-activation
SITE PREPARATION
Level the ground surface
Recommendation: Construct a wooden or concrete base as a foundation
External floor measurements are:
BEFORE STARTING ASSEMBLY
Read the care and safety guidelines at the end of this manual
Check to ensure that there are no missing or damaged parts BEFORE starting or
arranging assembly
Remove all parts from the package(s) and spread them out on a clean work
surface
Review all assembly instructions
Assemble all the parts according to the directions in this manual. Do not skip
any steps.
REQUIRED TOOLS
SPATULA
Use a spatula (part “SPA”) for easier insertion of the panel into
profile.
ASSEMBLY REQUIRES TWO PEOPLE
SHED PARTS
Remove all parts from the package(s) and spread them out on a clean work
surface
FLOOR PARTS
ROOF PARTS
WINDOW PARTS
WALL PARTS
DOOR PARTS 
SCREWS
SELF-DRILLING SCREW
Use a powerful electric screwdriver. The screw
should drill itself to a metal profile.
Packaging may contain some additional small parts for use as spare parts
NOTE: Due to variations in production, the actual assembled size may vary
slightly from the specified dimensions.
FLOOR ASSEMBLY
MPFP (x1) 168 x 168 cm / 66.1”x66.1”
Note: The crease line of the floor must be underneath
Turn over the floor panel
Fully fit the panel inside the profile
Turn over the floor panel
WALL ASSEMBLY
Use a spatula (part “SPA”) for easier insertion of the panel into the
profile.
Fully fit the panel inside the profile
Fully fit the panel inside the profile
Fully fit the panel inside the profile
Fully fit the panel inside the profile
• Fully fit the panel inside the profile
Fully fit the panel inside the profile
Fully fit the panel inside the profile
Fully fit the panel inside the profile
Fully fit the panel inside the profile
Fully fit the panel inside the profile
ROOF ASSEMBLY
• Fully fit the panel inside the profile
• Turn over the roof panel
• Ensure the roof is set fully down; use a spatula as shown in the figure
• Screw on the marked line
• Align holes in aluminum profiles with slits in the door panel
DOOR ASSEMBLY
• Turn over the door panel 
WINDOW ASSEMBLY
OPTION
SECURING THE SHED TO A FOUNDATION
Affix the shed to the foundation by drilling holes in the shed floor at the
pre-marked locations and screwing it into the foundation using appropriate
screws (screws not included].
CARE AND SAFETY GUIDELINES
-
The shed is intended for storage purposes only. It is not designed for habitation.
-
It is strongly recommended to secure the shed to an immovable object or anchor to the ground by drilling holes in the shed floor (at the pre-marked locations) and inserting proper screws into the ground (screws are not included).
-
Do not attempt assembly on windy or cold days.
-
Periodically check the shed to ensure that it is stable and that the site is level.
-
Be careful when handling parts with steel edges.
-
When assembling or handling the shed, use only those tools listed in the user manual.
-
Avoid using a lawnmower or mechanical scythe near the shed.
-
Wear safety goggles and always follow the manufacturer’s instructions when using power tools.
-
Wash the shed with a garden hose or a mild detergent solution. Do not use a stiff brush or abrasive cleaners, including degreasers and oil- or acetone-based cleaning materials, as these may stain or damage the shed.
-
Do not store hot items, such as recently used grills and blowtorches, and volatile chemicals in the shed.
-
Avoid placing heavy items against the walls, as this may cause distortion.
-
Keep the roof clear of accumulated snow and leaves. Large amounts of snow on the roof can damage the shed, making it unsafe to enter.
-
Wind direction is an important factor to consider when determining the location of the shed. Reduce exposure to the wind, in general, and of the door side in
particular. Keep doors closed and locked when the shed is not in use to prevent wind damage. -
Do not stand on the roof.
-
Consult your local authorities to check if permits are required to erect the shed.
10-YEAR LIMITED WARRANTY
Your Keter shed (“the Product”) was manufactured from high-quality, recyclable
materials under rigorous control and supervision.
Should a problem occur with the Product, please address your claim to Keter
customer service on our website (www.keter.com) or by
phone.
This warranty covers product failure resulting from defects in manufacturing
or materials for a period of 10 years from the date of original retail
purchase. (The term “defects” is defined as imperfections that impair the use
of the Product).
This warranty does not cover defects resulting from normal wear and tear,
including, but not limited to, scuffing, scratches or fractures caused during
use, discoloration or fading, rusting, unreasonable use, abuse, negligence,
alterations, painting, moving, transporting or relocating the Product, “acts
of Nature,” including, but not limited to, hail, any type of storm, flood and
fire, and consequential or incidental damages.
Assembly and handling not in accordance with the recommendations, guidelines,
and restrictions as described in the Product’s user manual, and used for
commercial or public applications, will void this warranty.
Keter is not responsible for any damage incurred by third parties or damage to
or loss of objects inside or near the shed.
Upon submitting proof of purchase and evidence of the claimed product failure,
and subject to reporting the failure in a timely manner, Keter, at its sole
discretion, will replace defective parts of the Product, or refund you a
prorated portion of the purchase price on a straight line depreciated basis
for the length of the warranty.
IF THERE ARE MISSING OR BROKEN PARTS, PLEASE DO NOT RETURN THE PRODUCT TO
THE STORE.
Please log onto our website, or contact Customer Service at:
WWW.KETER.COM
US, Canada:
Tel: +1877-638-7056
email: NACS@keter.com
Tel: +1-877-638-7056
Mon – Fri | 8am – 6pm ET
Lundi-Vendredi 8h -18h
Sat – Sun | 9am – 6pm ET
Samedi-Dimanche 9h-18h| UK:
Tel: +44-121-506-0008
email: CSUK@keter.com
2nd floor WESTPOINT, Mucklow
office park, Halesowen, West
Midlands, B62 8DY, United Kingdom
Mon – Fri | 8:30am – 5pm| Australia:
Tel: 03 9544 6999
Email: keteraus@keter.com
28 Buckland St,
Clayton, Victoria 3168
Mon – Fri | 9am – 5pm
---|---|---
South Africa
Tel: 0861-866-766
email: info@keter.co.za
Website: za.Keter.com| South Africa
Tel: 0861-866-766
email: info@keter.co.za
Website: za.Keter.com| Other European Countries
Tel: +31-1612-28300
email: service@keter.com
Mon – Fri | 8:30am – 5pm
A better world with Keter.
From material innovation to manufacturing processes we encourage sustainable
consumption.
Made in Israel by
Documents / Resources
|
KeTeR MANOR Pent
6x6
[pdf] User Manual
MANOR Pent 6x6, MANOR, Pent 6x6
---|---
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>