SIGNATURE HARDWARE 953853 Caviana Pendant Colgante Pendant Light Instruction Manual
- June 13, 2024
- Signature Hardware
Table of Contents
SIGNATURE HARDWARE 953853 Caviana Pendant Colgante Pendant Light
Product Information
- Product Name: CAVIANA Pendant Luminaire Suspendu Colgante
- SKU: 953853
- Manufacturer: Signature Hardware
- Care Instructions: To clean, wipe fixture with a soft cloth. Clean glass with a mild soap. Do not use abrasive materials such as scouring pads or powders, steel wool or abrasive paper.
Product Usage Instructions
- Before starting the installation, consult a professional if you are unfamiliar with installing electric fixtures. Signature Hardware accepts no liability for any damage to the property, the product, or for personal injury during installation. Observe all local electrical building codes.
- Unpack and inspect the product for shipping damage. If any damage is found, contact the Customer Relations team via live chat at www.signaturehardware.com or by emailing support@signaturehardware.com.
- Ensure that you have gathered all the required materials needed for the installation.
- Place one rod (P) down on top of each end of the fixture body (O) and in the middle of the fixture body (O).
- Lower the shade (K) down over the fixture body (O). Place the shade (K) down on top of the rods (P). Align the holes in the bracket on the shade (K) with the holes in the rods (P). Thread one thumbscrew (L) down into the holes in the bracket on the shade (K) and into the holes in the rods (P) and fixture body (O). Tighten thumbscrews (L) to secure the shade (K) in place. Do not over tighten.
- At least one 6 inch stem (N) must be used. Carefully push fixture wires up through the bottom of the 6 inch stem (N). Pull fixture wires out of the top of the stem (N) and pull them taut. Screw the bottom of the stem (N) onto the top of the fixture body (O).
- On the second side of the fixture, thread a 6 inch stem (N) onto the top of the fixture body (O).
- Determine the desired hanging height of the fixture. Select the quantity of stems (M) needed to achieve that height. Ensure the same quantity and size of stems are selected for both sides of the fixture.
If you have any additional questions or need further assistance, you can check out the Help Center at www.signaturehardware.com for product and warranty information, or contact the support team through live chat or by emailing support@signaturehardware.com.
BEFORE YOU BEGIN
We recommend consulting a professional if you are unfamiliar with installing
electric fixtures. Signature Hardware accepts no liability for any damage to
the property, the product or for personal injury during installation. Observe
all local electrical building codes.
Unpack and inspect the product for shipping damage. If any damage is found,
contact our Customer Relations team via live chat at www.signaturehard-
ware.com or by emailing support
@signaturehard-ware.com.
GETTING STARTED
Ensure that you have gathered all the required materials that are needed for
the installation.
FOR YOUR SAFETY
WARNING: Be sure the electricity to the wires you are working on is shut off, either the fuse is removed or the circuit breaker is shut off. You don’t need special tools to install this fixture. Be sure to follow the steps in the order given. Under no circumstances should a fixture be hung on house electrical wires, nor should a swag type fixture be installed on a ceiling which contains a radiant type heating system. Read instruc-tions carefully, if you are unclear as to how to proceed, consult a qualified electrician.
CARE INSTRUCTIONS
To clean, wipe fixture with a soft cloth. Clean glass with a mild soap. Do
not use abrasive materials such as scouring pads or powders, steel wool or
abrasive paper.
TOOLS AND MATERIALS
INSTALLATION
-
Place one rod (P) down on top of each end of fixture body (O) and in the middle of the fixture body (O).
-
Lower shade (K) down over fixture body (O). Place shade (K) down on top of rods (P). Align holes in bracket on shade (K) with holes in rods (P). Thread one thumbscrew (L) down into holes in bracket on shade (K) and into holes in rods (P) and fixture body (O). Tighten thumbscrews (L) to secure shade (K) in place. DO NOT over tighten.
IMPORTANT: At least one 6 inch stem must be used. -
Carefully push fixture wires up through bottom of 6 inch stem (N). Pull fixture wires out of top of stem (N). Pull fixture wires taut. Screw bottom of stem (N) onto top of fixture body (O).
-
On second side of fixture, thread 6 inch stem (N) onto top of fixture body (O).
-
Determine desired hanging height of fixture. Select the quantity of stems (M) to achieve that height.
IMPORTANT: Ensure the same quantity and size of stems are selected for both sides of fixture. -
Carefully push fixture wires through remaining stems (M). Thread stems (M) together carefully keeping fixture wires taut.
-
Push fixture wires up through loop (S). Pull fixture wires taut. Thread loop (S) onto top of last stem.
-
On second side of fixture, threaded remaining stems together. Screw loop (S) onto top of last stem.
-
Attach one locking link (G) to each loop (S).
-
Attach one section of chain (H) to each locking link (G) on each loop (S).
-
Push fixture wires up through hole in canopy (D).
-
Carefully pull house wires down out of junction box so house wires are easily accessible to connect fixture wires.
-
Position mounting bracket (A) so threaded ends A of attached fixture mounting screws (E) are facing down towards floor.
-
Carefully pull house wires through center hole in mounting bracket (A).
-
Align holes in mounting bracket (A) with holes in junction box. Thread junction box screws (B) into holes in mounting bracket (A) and into holes in junction box. Tighten junction box screws (B) to secure mounting bracket (A) to junction box.
-
Strip 3/4” of insulation from ends of fixture wires.
-
Twist the end of fixture white wire to the end of house white wire together. Twist a wire nut onto ends of wires. Wrap electrical tape around wire nut and wires to secure connection. Twist the end of fixture black wire and the end of house black wire together. Twist a wire nut onto the ends of wires. Wrap electrical tape around wire nut and wires to secure connection. Loosen ground screw on mounting bracket (A). Wrap house ground wire around ground screw leaving enough ground wire to attach to fixture ground wire. Twist the end of fixture ground wire to the end of house ground wire together. Twist a wire nut onto ends of wires. Wrap electrical tape around wire nut and wires to secure connection.
NOTE: If you have electrical questions consult your local electrical code for approved grounding methods. -
Carefully raise fixture up to ceiling. Place canopy.
- (D) over mounting bracket (A). Pass holes in canopy
- (D) over ends of fixture mounting screws (E).
-
Screw one threaded cap (F) onto each fixture mounting screw (E). Tighten threaded caps (F) to secure fixture to ceiling. DO NOT over tighten.
-
Screw recommended bulbs (E26 Edison bulb type, not included) into sockets. Verify correct bulb wattage marked on socket of fixture.
WARNING: DO NOT exceed maximum bulb wattage.
1.855.715.1800
signaturehardware.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>