SIGNATURE HARDWARE 484498 Colwick 4 Light 14 Wide Pendant Instruction Manual

: June 13, 2024
: Signature Hardware

Table of Contents

SIGNATURE HARDWARE 484498 Colwick 4 Light 14 Wide Pendant
Product Information
Product Care Instructions
Product Usage Instructions
FOR YOUR SAFETY
CARE INSTRUCTIONS
TOOLS AND MATERIALS
INSTALLATION
BEFORE YOU BEGIN
GETTING STARTED
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

SIGNATURE HARDWARE 484498 Colwick 4 Light 14 Wide Pendant

Product Information

The Colwick Pendant Luminaire is a suspended pendant light fixture designed for indoor use. It is SKU 953858 and is manufactured by Signature Hardware. The fixture comes with multiple arms and a center stem, allowing for an elegant and stylish lighting solution.

Product Care Instructions

To clean the fixture, use a soft cloth to wipe the surface. For the glass components, use a mild soap and gently clean them. Avoid using abrasive materials such as scouring pads, powders, steel wool, or abrasive paper.

Product Usage Instructions

Before beginning the installation, ensure that you have gathered all the required materials.
Pass the fixture wires up through the bottom of the center stem (N).
Thread the bottom of the center stem (N) onto the top of the fixture body (O).
Place the bottom of one arm (K) on top of one corner of the bottom frame (S).
Thread one ball stud (P) up through the bottom frame and into the bottom of the arm (K). Do not fully tighten the ball stud (P) at this stage.
Repeat step 4 for the remaining arms (K).
Pass the hole in the center of the top frame (R) over the top of the center stem (N).
Align the holes at the end of each arm of the top frame (R) with the holes in the top of each arm (K).
Thread one screw (L) down through each hole in the top frame and into the holes in the arm (K). Do not completely tighten the screws (L) at this stage.
After all arms (K) are attached, completely tighten all ball studs (P) and screws (L).
Pass the fixture wires through the bottom of the loop (M).
Thread the loop (M) onto the top of the center stem (N).
Connect one locking link (G) to the loop (M).
Determine the desired hanging height of the fixture. If needed, cut the chain (H) to achieve the desired height.

For any additional questions or assistance, you can visit the Help Center at www.signaturehardware.com for product and warranty information. Alternatively, you can reach out to Signature Hardware’s Customer Relations team through live chat or by emailing support@signaturehardware.com.

FOR YOUR SAFETY

WARNING: Be sure the electricity to the wires you are working on is shut off, either the fuse is removed or the circuit breaker is shut off. You don’t need special tools to install this fixture. Be sure to follow the steps in the order given. Under no circumstances should a fixture be hung on house electrical wires, nor should a swag type fixture be installed on a ceiling which contains a radiant type heating system. Read instruc- tions carefully, if you are unclear as to how to proceed, consult a qualified electrician.

CARE INSTRUCTIONS

To clean, wipe fixture with a soft cloth. Clean glass with a mild soap. Do not use abrasive materials such as scouring pads or powders, steel wool or abrasive paper.

TOOLS AND MATERIALS

INSTALLATION

Pass fixture wires up through bottom of center stem (N). Thread bottom of center stem (N) onto top of fixture body (O).
Place bottom of one arm (K) on top of one corner of bottom frame (S). Thread one ball stud (P) up through bottom frame and into bottom of arm (K). DO NOT fully tighten ball stud (P). This will be done after fixture is assembled. Repeat this step for remaining arms (K).
Pass hole in center of top frame (R) over top of center stem (N). Align holes at end of each arm of top frame (R) with holes in top of each arm (K). Thread one screw (L) down through each hole in top frame and into holes in arm (K). DO NOT completely tighting screws (L).
After all arms (K) are attached, completely tighten all ball studs (P) and screws (L).
Pass fixture wires through bottom of loop (M). Thread loop (M) onto top of center stem (N).
Connect one locking link (G) to loop (M).
Determine desired hanging height of fixture. Cut chain (H) to length to achieve desired height.
Slip chain link at end of chain (H) onto locking link (G) on loop (M).
Weave fixture wires through chain links, skipping every other chain link.
Slip threaded ring (F) down over end of chain (H) andfixture wires.
Slip hole in canopy (D) over end of chain (H) and fixture wires
Hold mounting bracket (A) so head of ground screw is pointing down towards floor. Hold threadedpipe so two hexnuts already attached to threaded pipe (E) are pointing down towards floor. From side of mounting bracket with ground screw head, screw short end of threaded pipe (E) into hole in center of mounting bracket (A) until hexnut on threaded pipe (E) touches mounting bracket. Thread hexnut (V) onto end of threaded pipe (E). Tighten hexnut (V) to secure threaded pipe (E) to mounting bracket (A).
Thread screw collar loop (W) onto end of threaded pipe pointing down towards floor. Tighten screw collar loop up against hexnut on threaded pipe (E).
Place mounting bracket (A) up against junction box. Screw collar loop (W) should be pointing down towards floor. Align each slot in mounting bracket (A) with each hole in junction box. Thread one junction box screw (B) into each slot in mounting bracket (A) and into holes in junction box. Tighten junction box screws (B) to secure mounting bracket (A) to junction box
- CAUTION: Make sure house wires are still easily accessible. DO NOT pinch wires between mounting bracket and ceiling.
Strip 3/4° of insulation from ends of fixture wires.
Push fixture wires up through hole in screw collar loop (W) attached to mounting bracket (A) and out end of threaded pipe inside junction box. Carefully pull fixture wires so they are easily accessible to connect to house wires
To aid in connecting fixture wires to house wires, temporarily connect second locking link (G) to link at end of chain (H) and to screw collar loop (W).
Twist the end of fixture white wire to the end of house white wire together. Twist a wire nut onto ends of wires. Wrap electrical tape around wire nut and wires to secure connection. Twist the end of fixture black wire and the end of house black wire together. Twist a wire nut onto the ends of wires. Wrap electrical tape around wire nut and wires to secure connection. Loosen ground screw on mounting bracket (A). Wrap house ground wire around ground screw leaving enough ground wire to attach to fixture ground wire. Twist the end of fixture ground wire to the end of house ground wire together. Twist a wire nut onto ends of wires. Wrap electrical tape around wire nut and wires to secure connection.
- NOTE: If you have electrical questions consult your local electrical code for approved grounding methods
After wires are connected, carefully tuck wires inside junction box.
Remove second locking link (G) from last link on chain (H) and screw collar loop (W).
Raise canopy (D) up to ceiling. Pass hole in canopy (D) over screw collar loop (W). Position canopy (D) up against ceiling.
Raise threaded ring (F) up to canopy (D). Screw threaded ring (F) onto screw collar loop (W). Tighten threaded ring (F) to secure fixture to ceiling.
Attach second locking link (G) to link at end of chain (H). Attach locking link (G) at end of chain (H) to loop on screw collar loop (W).
Screw recommended bulbs (E12 candelabra bulb type, not included) into sockets. Verify correct bulb wattage marked on socket of fixture.
- WARNING: DO NOT exceed maximum bulb wattage.

BEFORE YOU BEGIN

We recommend consulting a professional if you are unfamiliar with installing electric fixtures. Signature Hardware accepts no liability for any damage to the property, the product or for personal injury during installation. Observe all local electrical building codes. Unpack and inspect the product for shipping damage. If any damage is found, contact our Customer Relations team via live chat at www.signaturehardware.com or by emailing support@signaturehardware.com.