inoxbazis Electric Bain Marie Kit Instructions

: June 13, 2024
: Inoxbazis

Table of Contents

ELECTRIC BAIN MARIE
Dear Costumer!
ATTENTION
CLEANING
GENERAL DESCRIPTION
TECHNICAL DATA
BODY ASSEMBLY
INSTRUCTIONS FOR ASSEMBLY OF THE GLASS STRUCTURE
STARTING THE BAIN MARIE
DRAINING THE WATER
MAINTENANCE
CUSTOMER SUPPORT
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

inoxbazis Electric Bain Marie Kit

inoxbazis Electric Bain Marie Kit

ELECTRIC BAIN MARIE

Dear Costumer!

First of all, thank you for choosing us and honoring us with your trust! We hope that you found everything in ideal condition and are satisfied with the product!

Before using the product, make sure that it has been assembled and installed in accordance with the instructions!

ATTENTION

The equipment may only be used by a trained personnel!
Never leave the device on without water in the tank!
Do not leave children or disabled people unattended with the device in one space!
Always observe the site-specific safety, occupational safety, fire and accident prevention, and the hygiene regulations!
The manufacturer is not responsible for damages resulting from improper use, maintenance and repair work performed by non-professionals, nor for the proper functioning of non-original spare parts.
Place the device on a straight, flat, solid surface, in a place that complies with the regulations, so that there is no danger of tipping over or slipping.
To connect to the electrical network, it is advisable to install a circuit breaker between the equipment and the network. With regard to establishment safety regulations, MSZ HD 60364-
4- 41:2007 standard, the provisions of MSZ EN 61140:2003 must be taken into account with regard to the contact protection regulations. Do not operate the device without an effective touch protection!
Always check if the device is working properly during use. If you notice an error, disconnect the machine from the network and call a specialist.

CLEANING

Do not clean the device with a high-pressure water jet! Before cleaning, wait for the machine to cool down and disconnect the device from the electrical network.
Wash all metal parts with warm water and neutral detergent, then rinse thoroughly to remove any remaining dirt from the machine.
Use a dry cloth to dry. Do not use abrasive or corrosive cleaning agents as they may damage the metal parts of the equipment.
In the event that the equipment is not used for a long period of time, clean it thoroughly and disconnect it from the electrical network.
If the machine breaks down, switch it off immediately and contact a mechanic.

GENERAL DESCRIPTION

The counters are covered on three sides, are normally opened in the front, and have a bottom shelf. All counters are made of stainless steel. The device is equipped with an internal filament heating. Optional: wheel set, external heating blanket, filling tap, bottom heating. The GN container is not a standard accessory!

ATTENTION! THE MANUFACTURING COMPANY RESERVES THE RIGHT TO MAKE ANY CHANGES
DEEMED NECESSARY TO IMPROVE THE MACHINE, AND TOGETHER WITH THE DISTRIBUTION
COMPANY, THEY DISCLAIM ANY LIABILITY FOR DAMAGES RESULTING FROM IMPROPER USE.
This product contains components that are classified as hazardous waste, which – depending on the type of machine – includes coolant gases, coolants, electronic (semi)conductors, etc. contains, which seriously damages the environment, that is why it can only be collected separately as a waste! During the development of the manufacturer’s technology, it devotes a significant proportion of its income to research and development in order to reduce the amount of waste from e+e equipment and make their reuse, utilization and processing significantly easier.

TECHNICAL DATA

Data of standing versions	RMKM3GN11	RMKM4GN11	RMKM5GN11
Size	1150×700×850 mm	1500×700×850 mm	1800×700×850 mm
Capacity	3×GN1/1	4×GN1/1	5×GN1/1
Heating filament performance	1,3 kW	2,6 kW	2,6 kW
Heating blanket performance	2,3 kW	2,3 kW	3,3 kW
Thermostat	30-90°C	30-90°C	30-90°C
Data for desktop versions	RMAM3GN11	RMKM4GN11	RMAM5GN11
---	---	---	---
Size	1150×700×275 mm	1500×700×275 mm	1800×700×275 mm
Capacity	3×GN1/1	4×GN1/1	5×GN1/1
Heating filament performance	1,3 kW	2,6 kW	2,6 kW
Heating blanket performance	2,3 kW	2,3 kW	3,3 kW
Thermostat	30-90°C	30-90°C	30-90°C

The version with a heating blanket is an extra option.

BODY ASSEMBLY

Different types of superstructures and breathing protection glass can be ordered for the electric bain maries. Attention: The counters are sold without a superstructure by default in order to make them easier to transport. In this case, the assembly is carried out by the customer. If the customer also requests assembly, this must be indicated to the manufacturer. In this case, the specialist representing the manufacturer will carry out the assembly at the location for an additional fee.

BODY ASSEMBLY:

INSTRUCTIONS FOR ASSEMBLY OF THE GLASS STRUCTURE

The glass must be slid into the glass holders (1) located below. The glass must be screwed with the help of the “L” shaped side element (2) or the corner element (3) into the holes placed in the column above. It is important that the silicone rubber ring (4) in the assembly package is placed at the junction of the glass and metal parts. The thermal expansion of glass and metal is not the same, the 1 mm plastic ring serves to balance of this factor. Without the plastic ring, there is an increased risk of breakage of the fixed screws during use, the glass will break sooner or later even with normal use, so make sure that the glass is properly fixed!

| |

``

|
---|---|---|---

STARTING THE BAIN MARIE

Remove the protective folie of the device. Before first use, clean the device thoroughly with a damp cloth and a neutral detergent.
It is equipped with a wire and plug, which can be used to connect to the 230V / 50Hz electrical network. Make sure that the drain valve is closed. Fill the tank with water to cover the bottom by at least 5 cm, then turn on the machine with the main switch. The device is equipped with a heating wire built into the most modern silicone sheet known today, but if there is no water in it, it will overheat and, of course, it can burn out. Turn on the main switch and use the rotary knob to set the thermostat to the desired temperature (between 30-90 C). After that, the thermostat is no longer needed to turn it on and off, only the main switch is used to turn it on and off.

DRAINING THE WATER

First, get a suitable container into which the water can be drained. Then open the drain tap. The device connected to the mains can be filled directly with the tank filling inlet, which is available as an option, and the water draining can be simplified with the drain tap, which is connected to the mains.

MAINTENANCE

All maintenance operations may only be carried out by trained personnel. In such cases, always switch off the machine and disconnect it from the electrical network.

When switching off, turn off the main switch, then the power supply to the device will be cut off. The lighting works by turning on the main switch, in case the replacement is needed, it is important to disconnect the device first and then carry out the replacement of the lamp.