SEALEY VS0202.V3 Workshop Vacuum Brake and Clutch Bleeder Instruction Manual
- June 13, 2024
- SEALEY
Table of Contents
SEALEY VS0202.V3 Workshop Vacuum Brake and Clutch Bleeder Instruction
Manual
- Refer to instruction manual
- Wear eye protection
- Wear protective gloves
SAFETY
-
WARNING! Familiarize yourself with the application and limitations, as well as any potential hazards, of this product. Ensure that Health and Safety, local authority and general workshop practice regulations are adhered to when using.
-
DO NOT use pressure reservoir, or its ancillaries if damaged.
-
DO NOT use the pressure reservoir to perform a task for which it is not designed.
-
DO NOT allow untrained persons to use the pressure vessel.
-
DO NOT use when tired or under the influence of drugs, alcohol or intoxicating medication.
-
Use approved parts and approved spare parts only.
-
Maintain in a good and clean condition for the best and safest performance.
-
Ensure that the ignition key of the vehicle being worked on is removed, to prevent inadvertent engine cranking.
-
If the vehicle to be worked on is raised, ensure that it is adequately supported with axle stands or ramps and wheel chocks.
-
Wear approved eye protection. A full range of personal safety equipment is available from your Sealy stockiest .
-
Wear suitable clothing to avoid snagging. DO NOT wear jeweler and tie back long hair.
-
Keep children and unauthorized persons away from the work area.
-
Keep work area clean and tidy and free from unrelated materials.
-
Ensure the work area has adequate lighting.
BRAKE FLUID SAFETY -
Always read and comply with the warnings on the brake fluid container.
-
Wear eye protection and keep skin contact to a minimum. If brake fluid enters eyes rinse with plenty of water and seek medical advice. If swallowed seek medical advice immediately.
-
WARNING! Brake fluid is flammable – keep away from sources of ignition, including hot surfaces e.g. exhaust manifold.
-
WARNING! Brake fluid will damage paintwork. Any spillage should be flushed with water immediately.
-
Always read and comply with the warnings on the brake fl uid container.
-
WARNING! DO NOT pollute the environment by allowing uncontrolled discharge of fl uids. Dispose of waste liquids in accordance with local authority regulations.
-
After use, clean equipment and store in a cool, dry, childproof area.
INTRODUCTION
One-person operation using standard workshop air supply (90-120psi). Professional, quick, clean and. Large capacity for the busy workshop. Draws fluid from the bleed nipple enabling either bleeding or full replacement of fluid in system. Vacuum gauge for precise application. Separate cap for easy emptying. Long lasting silicone rubber hose for ultra flexibility. Includes reservoir top-up kit and adaptors
SPECIFICATION
Model No: .VS0202.V3
Air Consumption: 180L/min
Inlet Size : 1/4”BSP
Maximum Air Supply: 120psi
Tank Capacity: 2.5L Key
- Trigger
- Hose assembly
- Container
- Pressure gauge
- Top cap
- N/A
- Replenishment bottle
- 9, 10, 11 Adaptors
OPERATION
BRAKE BLEEDING PROCEDURE
Refer to the vehicle manufacturer’s instructions for brake bleeding and wheel
sequence before proceeding. If no specific instructions from the vehicle
manufacturer exist, follow the instructions detailed below.
- WARNING! Familiarize yourself with the hazards of brake fluid – read manufacturer’s instructions on the container. Do not touch the vehicle’s brake pedal whilst bleeding the brakes. Remove the cap of the vehicle’s brake fluid reservoir. If the brake fluid level is not at maximum, top it up. Fill the replenishment bottle to just under half full with new brake fluid, then screw the cap assembly onto the replenishment bottle. Invert the bottle over the container of new brake fluid and open the valve ‘D’ so that the fluid level begins to drop towards the level marked on the bottle. As soon as the level mark is reached, close the valve.
Screw on an appropriate size three legged adaptor that fits into the top of the brake fluid reservoir. Ensure valve ‘D’ is closed, and invert the replenishment bottle within the neck of the brake fluid reservoir as shown in fig.1. The threaded outlet ‘B’ must be immersed in the brake fluid. If it is not, screw the three legged adaptor ‘C’ clockwise towards the valve ‘D’ until sufficient thread is exposed to allow the outlet to be immersed in the brake fluid. Open the valve ‘D’ as in fig.2. As the brakes are bled, the fluid level in the reservoir will begin to drop and expose the bottle outlet. Brake fluid will begin to flow from the replenishment bottle. Once the level in the reservoir has risen sufficiently to cover the outlet, the flow will automatically stop. Depending on the amount of brake fluid bled from the system, the bottle may need to be filled again from time to time.
NOTE: Apply copper grease to the brake bleeding nipples before and after
the brake bleeding procedure to reduce the possibility of seized or broken
nipples when the brakes are next bled (fig.5).
Connect the brake bleeder to a suitable compressed air supply.
Connect the rubber adaptor onto the brake nipple on the first wheel and open
the nipple about one quarter of a turn (fig.3).
Activate the brake bleeder’s valve. The vacuum created will draw the brake
fluid from the vehicle’s brake system.
Continue to bleed the system until there are no air bubbles visible in the
clear tube (fig.4).
Retighten the brake nipple and close the bleeder’s valve (fig.3).
Remove the rubber adaptor from the brake nipple.
Open the valve on the brake bleeder to remove any brake fluid from the clear
pipe.
Repeat the process at each wheel in turn as necessary.
CHANGING THE BRAKE FLUID
Carry out the brake bleeding procedure as described above. As the fluid is
being completely changed, regularly check the level in the replenishment
bottle.
When new fluid can be seen in the clear tube tighten the brake nipple.
Repeat this procedure at each wheel in turn.
When brake bleeding and/or fluid changing is complete, test the action of
the brake pedal to ensure that the brakes are working and are not spongy,
before using the vehicle on the road.
CLUTCH BLEEDING PROCEDURE
Refer to the relevant vehicle manufacturer’s instructions for clutch bleeding
procedure. If no specific instructions from the vehicle manufacturer exist,
the instructions basically follow the same procedure as the brake bleeding
instructions in steps through to
ENVIRONMENT PROTECTION
Recycle unwanted materials instead of disposing of them as waste. All tools,
accessories and packaging should be sorted, taken to a recycling center and
disposed of in a manner which is compatible with the environment. When the
product becomes completely unserviceable and requires disposal, drain any
fluids (if applicable) into approved containers and dispose of the product and
fluids according to local regulations.
REGISTER YOUR PURCHASE HERE
Note: It is our policy to continually improve products and as such we
reserve the right to alter data, specifications and component parts without
prior notice.
Important: No Liability is accepted for incorrect use of this product.
Warranty: Guarantee is 12 months from purchase date, proof of which is
required for any claim.
Sealy Group, Kimpson Way, Suffolk Business Park, Bury St Edmunds, Suffolk.
IP32 7AR
01284 757500
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>