niko PM353-652021 Presence Detector User Manual

June 13, 2024
niko

Manual
Presence detector
353-652021
4 year warranty

Presence detector P46MR, DALI-2, secondary and BMS, 12-13 m, 360°, for surfacemounting

Wiring
230 V/DALI power – OFF

Secondary

This product must be secured with a miniature circuit breaker (MCB) of max. 16 A in the electrical cabinet. The MCB rating is limited by national installation rules.

BMS

Dimensions

Installation

If a grommet needs to be replaced, please make sure the new grommet is halogen-free.

Dismantling

App settings

App-instellingen

| Sensitivity
---|---
Factory Settings| High

Settings by BMS software

DALI BMS-instellingen
Table memory bank 2

Address Description Default value Memory type
Ox00 Address and last accessible memory location 0x03 ROM
Ox01 Indicator byte (manufacture definable) Ox00 any
0x02 Memory bank lock byte (00×55 = Read Only else
Read/ Write) OxFF RAM
Ox03 PIR sensitivity segment A (MR, LR and HC detectors)
4 = MAX 3 = HIGH 2 = LOW 1 =MIN 0 = OFF 0x03 NVM
Ox04 PIR sensitivity segment B (LR and HC detectors)
4 = MAX 3 = HIGH 2 = LOW 1 = MIN 0 = OFF 0x03 NVM
0x05 PIR sensitivity segment C (LR and HC detectors)
4 = MAX 3 = HIGH 2 = LOW 1 =MIN 0 = OFF Ox03 NVM
0x06 LUX range

0 = NORMAL 0 – 1023 lux, 10-bit
1 = HIGH 0 – 10360 lux, 14 bit| Ox00| NVM
0x07| Bluetooth® communication
0 = enabled, 1 = disabled| Ox00| NVM

Note : The detector reboots when Bluetooth ® communication is disabled or re-enabled. This lasts for approximately 100 – 500 ms.

LED behaviour

Green LED continuous on|           | Connection OK|
---|---|---|---
Green LED flashing| | Warming up*| Wait
Red LED continuous on| | Error| More into –>
Blue LED flashing| | Walk test active

  • When Bluetooth ® communication is disabled, the green LED does not flash while warming up.

Specifications

Article number 353-652021
Configuration DALI-2 secondary/BMS
Input voltage via the DALI bus
Maximum current consumption 28.1 mA
Nominal current consumption (12 V, 25°C) Bluetooth® enabled 8.1 mA
Nominal current consumption (12 V, 25°C) Bluetooth® disabled 5.0 mA
Maximum startup time DALI < 1200 ms
Maximum PIR detection startup time 70 s
Light intensity range 0 – 10360 lux (see DALI BMS settings)
Detection angle 360 °
Detection range (PIR) ø 12 m from a height of 3 m
Ambient temperature -25 – +40 °C
Mounting method surface mounting
Mounting height 2 – 3.5 m
Colour white (RAL 9010)
Dimensions visible (HxWxD) 100 x 100 x 50 mm
Dimensions (HxWxD) 100 x 100 x 50 mm
Wire capacity 1.5/2.5 mm²
Maximum range Bluetooth ® (free field, depending on the device) 50 m
Operating frequency 2.4 GHz
Maximum radio frequency power -2 dBm
Protection degree IP54
Impact resistance IK02
Modification of settings app (iOS/Android) and 2-way Bluetooth ®

communication/BMS software
Halogen-free| yes
Marking| CE

Detection area

Troubleshooting

Problem Possible cause Proposed solution
Load does not turn on The wiring is not correct Check the wiring scheme
Load does not turn off The detector receives false triggers Check for any

objects that may cause false triggering and remove them
from the detection range or lower the sensitivity
App cannot connect to the detector| Bluetooth ®  has been disabled on your mobile device or on the detector| Enable Bluetooth ®  on your mobile device or on the detector

Support & contact

nv Niko sa
Industriepark West 40
9100 Sint-Niklaas, Belgium
www.niko.eu
+32 3 778 90 80
Niko prepares its manuals with the greatest care and strives to make them as complete, correct and up to date as possible. Nevertheless, some deficiencies may subsist. Niko cannot be held responsible for this, other than within the legal limits. Please inform us of
any deficiencies in the manuals by contacting Niko customer services at support@niko.eu.

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals