better bathrooms LISLPG1650 Freestanding Double Ended Bath User Manual

: June 13, 2024
: Better Bathrooms

Table of Contents

better bathrooms LISLPG1650 Freestanding Double Ended Bath
Product Information
Product Usage Instructions
Important information
Receive Your Bath
Tools required
Installation
Troubleshooting
Maintenance & Cleaning
For more information
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

better bathrooms LISLPG1650 Freestanding Double Ended Bath

Product Information

The freestanding bath is a two-person assembly product. It is recommended to use professional tradespeople for installation. The bath is not designed to take weight on the rim, so sitting or standing on the bath rim should be avoided.

Product Usage Instructions

Receive Your Bath: Unpack the bath and check for any damage. If there is any damage, notify the seller in a timely manner. If the bath is not being immediately installed, repack it.
Protect Your Bath: Before installation, ensure that the bath is completely protected. Leave the covering in place until the bathroom is complete to avoid scratches and damage.
Tools Required: You will need a spirit level, wrench, tape, marking pencil, and silicone gun.
Installation:
- Set the feet of the bath at 3mm above the floor (refer to Figure 1).
- Install the flexible connector (not supplied) as shown in Figure 2.
- Apply silicone around the base surrounding of the bath (refer to Figure 3).
Important Note: Allow the silicone to fully cure for 24 hours before using the bath.
Troubleshooting: Marks found on the surface can be wiped off with a wet cloth and toothpaste.
Maintenance & Cleaning:
- Water test your bath before enclosing or tiling to ensure proper drainage.
- Test the overflow pipe and waste to ensure they are not leaking.
Warning: If the bath is pre-fitted with a waste, it should be properly installed by a qualified installer to avoid water leakage.

For further assistance or inquiries, you can contact us via betterbathrooms.com/content/contact-us.

Congratulations on your purchase
And welcome to our growing gang of savvy shoppers We’re on a mission to bring you extraordinary bathroom products, for less. From modern to traditional style ceramics, plus the gorgeous fixtures, fittings and furniture to match. So, you can fall in love with your space every single day. As one of the UK’s largest independent bathroom stores, we’ve received countless awards; including the National Business Awards UK, the Digital Entrepreneur Awards and being placed on The Sunday Times Fast Track 100.
We hope your new product goes above and beyond your expectations. However, should any problems occur, please:

log in to your account and contact our customer services team via your self-serve portal – betterbathrooms.com/CustomerAccount/Login.
contact us via betterbathrooms.com/content/contact-us.

Important information

Please read these instructions thoroughly and retain for future reference
Always check for pipes and cables before drilling
Freestanding bath is not designed to take weight on the rim, Do not sit or stand on the bath rim.

Receive Your Bath

Unpack and check for damage.
After receiving your bath, please unpack and remove all covering, checking whether there is any damage. Repack the bath if it is not being immediately installed. It will be rejected any claim for damage if not notified in a timely manner.
Protect your bath.
Before commencing and installation, ensure the bath is completely protected, leave covering in place until the bathroom is complete. Scratches and damage incurred during installation are not covered by the warranty.

Tools required

$better-bathrooms-LISLPG1650-Freestanding-Double-Ended- Bath-fig-1 $1$$

Installation

Step 1
Adjust the bath feet until the bath base is 3mm above the floor; This can be done by turning the feet bars accordingly; Then use wrench to tighten the nuts on the bars. See figure 1
Step 2
Mark the floor with the outline of the bath, at the final installation position with the marking pencil.
Step 3
Carefully tilt the bath on its side and use flexible connector to connect the waste outlet to the trap as illustated on figure2.
Step 4
Position the bath on the floor marking as marked on step 2, make sure that flexible connector is not kinked upward on installation as this will result in drainage issue.
- Feet set at 3mm above the floor
- Flexible connector installation Flexible connector and waste trap are not supplied
Step 5
Apply silicone around the base surrounding of the bath, see figure 3.
- Do not use the bath within 24 hours to let the silicone fully cure

Troubleshooting

Marks found on the surface could be wiped off with wet cloth and toothpaste.

Maintenance & Cleaning

To preserve the polished surface, after using your bath, clean with soft cloth and warm soapy water to wash away any body oils or soap residue that forms a ring tide mark.
Do not use powders, pastes, crème cleaners, thinners, window cleaning sprays or dry cleaning liquid, etc.
When coloured essentials oils are used, first test that the colour won’t stain your bath. Always add oils into a bath full of water. Never pour them into an empty bath.

Water testing

Water test your bath prior to enclosing to ensure it drains correctly as no claims for nondraining baths will be valid after enclosing or tiling has been done;
Water test overflow pipe and waste to ensure they are not leaking.

Warning (apply to bath prefitted with waste)

The pre-fitted waste has NOT yet been fully installed.
Please use a qualified installer to secure it to the bath to avoid any water leaking.
Before use please test the bath to ensure the waste has been properly installed.