puck-keysafe 3333 Smart Lock Instruction Manual

**puck-keysafe 3333 Smart Lock Instruction Manual

**

Manual for the installer and end user

Dear customer,

Thank you for purchasing the Puck Keysafe. This manual contains all the information needed to quickly familiarize yourself with the product. We kindly request you to go through this information carefully, before you start to work with the product.
This manual is intended for installers and end users of the Puck Keysafe. This is the original manual. Keep these instructions safe!

For more information, please contact your local Puck Dealer, which you can find on: www.puck-keysafe.com.

Introduction

With Puck Keysafe you can store your keys safely where you need them. The Puck Keysafe has been SKG approved and graded as . The Puck Keysafe can be accessed by entering a four-digit code. The Puck Keysafe has two safeguards to keep your secret code from third parties:**

1. The Puck Keysafe is equipped with an anti-reading cap. This cap makes it more difficult for third parties to look over your shoulder as you enter your PIN.
2. When you open the Puck Keysafe, the code does not remain, but switches to another number combination.

Intended use

The Puck Keysafe is a key safe, designed for you to store your house keys safely in the home. The Puck Keysafe can be opened using a four-digit code. You set this code yourself. Make sure you know the code before closing the key cabinet of the Puck Keysafe. Do not share your code with third parties.

The Puck Key safe can be mounted on a stone or concrete wall, or on a door by means of a mounting bracket.

Used symbols

The following four marking conventions are used in this manual:

Attention! A note with additional information to the user. A note which alerts the user to potential problems.

Puck Keysafe is certified according to the assessment directive SKG IKOB KE 470 with the classification of 2 stars. This means that an unauthorised person needs more than 3 minutes to break open the safe.

Main components

Figure 1. Main components

1. Anti-read cap
2. Cover
3. Key cabinet
4. Mounting plate
5. Mounting bracket (optional)

Fixings

Figure 2. Safe fixing

Figure 3. Fixing mounting bracket

1. Hexagon bolt M8 x 40 mm (3x)
2. Wall Anchor (3x)
3. Hex nut M6 (3x) (optional)
4. Wood screw (4.5 x 30 mm) (optional)
5. Coach bolt M6 x 25 mm (3x) (optional)

Operating elements

Figure   4. Operating elements

1. Figure Wheels
2. Code setting slider

Mounting

The Puck Keysafe can be mounted in two ways:

1. Mounting on a brick or concrete wall.
2. Mounted onto a door or a door frame.

Mounting the Puck Keysafe on a brick or concrete wall

Attention

• Mounting should preferably be performed by a qualified installer.
• The wall where the safe is to be mounted must be flush.
• The wall must be made of brick or concrete.

To mount the Puck Keysafe on a wall, do the following:

1. Open the Puck Keysafe. The code is factory preset to 3333.

2. Using the number wheels enter the code ‘3333’.

3. Turn the lid anti-clockwise and then pull it toward you.

4. Determine where you want to mount the Puck Keysafe. The height must be 120-150 cm.

5. Keep the mounting place to the desired location so that two holes are facing up and one hole is facing down.
   Figure 5. Position the Puck Keysafe
   

6. Mark the holes.
   Figure 6. Mark the holes
   
   Attention
   The holes cannot be drilled into the joints

7. Drill three 12 mm holes 85 mm deep.
   Figure 7. Drill the holes
   

8. Insert the wall anchors.
   Figure 8. Insert the wall anchors
   

9. Activate the wall anchors by turning them with a hexagonal spanner. Remember that when tightening the wall anchors will be pulled a few millimetres into the wall.
   Figure 9. Activate the wall anchors
   

10. Mount the key cabinet on the wall with the hexagonal bolts. Tighten the bolts by hand.
    Figure 10. Mount the key cabinet on the wall
    

11. Change the code. For more information see paragraph 4.2.

12. Place the cover.

13. Slide the cover over the key cabinet and turn it. Make sure the line on the cover is aligned with the line on the mounting bracket. You will hear a click.
    Figure 11. Place the cover
    

Well done! You have completed the mounting.

Mounting the Puck Keysafe onto a door or a door frame

Attention
Mounting should preferably be performed by a qualified installer.

To mount the Puck Keysafe on a door or a door frame, do the following:

1. Open the Puck Keysafe. The code is factory preset to 3333.

   • Using the number wheels enter the code ‘3333’.
   • Turn the lid anti-clockwise and then pull it toward you.

2. Screw the key cabinet onto the mounting bracket. Use the three bolts and the hex nuts.
   Figure 12. Screw the key cabinet onto the mounting bracket
   

3. Open the door.

4. Screw the mounting bracket firmly onto the door or the door frame on the side where the hinges are located. The height must be 120-150 cm.
   Figure 13. Screw the mounting bracket onto the door or the door frame
   

5. Carefully check whether you can still close the door.
   If not, stop the assembly, remove the wall bracket and contact your dealer.

6. Place the cover.

7. Slide the cover over the key cabinet and turn it. Make sure the line on the cover is aligned with the line on the mounting bracket. You will hear a click.
   Figure 14. Place the cover
   

Well done! You have completed the mounting.

Use

Open the Puck Keysafe

1. Enter the correct code, by turning the number wheels.
   Figure 15. Enter the correct code
   

2. Turn the cover anti-clockwise and hold it.

3. Pull the cover towards you.
   Figure 16. Remove the cover
   

Ttip The key safe has two slots. You can temporarily ‘park’ the cover there. In this way, you have your hands free.

Figure 17. You can temporarily place the cover in the two slots

Setting the code

Tip Change the code regularly.

To set the code, do the following:

1. Remove the lid. (see: Opening Puck Keysafe)

2. Re-enter the original opening code.

3. Set the code setting slider to the position SET CODE.
   Figure 18. Set the code setting slider to the position SET CODE

4. Rotate the number wheels to the code you want to set.
   Figure 19. Setting the code
   
   Attention Don’t forget the code.
   Tip Choose a code that is difficult for others to guess but easy for you to remember.

5. Check if the code is set correctly. Set the code setting slider back on the high position.

6. Rotate one of the number wheels one position. To make sure the code is set correctly the code setting slider must be fixed into its position.
   Figure 20. Set the code setting slider back on the high position

You have now set the code.
You can put the cover back again.
You can open the Puck Keysafe with the code you just set.

Maintenance, environment and disposal

With normal use the Puck Keysafe is maintenance-free.
Please dispose of the product and packaging according to the local regulations.

Guarantee

We offer a 2 year guarantee on functionality for normal use in accordance with these instructions.

De Beer Innovations BV Accustraat 4
NL – 3903 LX Veenendaal The Netherlands
www.puck-keysafe.nl

References

• Puck Keysafe | De veilige sleutelkluis die overal en bij iedereen past
• Puck Keysafe | De veilige sleutelkluis die overal en bij iedereen past

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>