b d SDO-6 Sectional Door Openers User Guide

b d SDO-6 Sectional Door Openers

USER OPERATING CONTROLS

MANUAL DOOR OPERATION

TO DISENGAGE THE OPENER

It is recommended to disengsgre the door with the door in the closed position.

Pull towards, until you hear a click
Manually operate door

CAUTION: When the opener is manually disengaged, the door is no longer locke d . To lock the door manually, re-engage the opener after the door is closed.

CODING A REMOTE CONTROL

The opener can only be operated from remote controllers that have been programmed into its memory. Up to 64 remotes can be programmed.

• STEP ONE
  Switch power on and remove controls cover

• STEP TWO
  Press repeatedly
  till remote LED lit
  

• STEP THREE
  HOLD Opener Flashes & beeps
  HOLD for 3 sec HOLD for 3 sec RELEASE Release both buttons
  

• STEP FOUR
  Then refit controls cover
  

• STEP FIVE
  Press to test

REMOTELY CODING A REMOTE CONTROL

Remotely coding works when you have a pre-coded remote control and are in range of the opener.

1. **STEP ONE

**

2. STEP TWO
   Use a pen, HOLD for 2 sec the middle button through the coding hole

3. STEP THREE
   Opener Flashes & beeps
   Take new remote

HOLD for 3 sec HOLD for 3 sec RELEASE RELEASE

4. STEP FIVE
   Opener stops flashing & beeping

Press to test

CHANGING A BATTERY

Battery Type: 1 x CR2032.

1. STEP ONE
   Check Light Status Table
   Light Status| Battery
   ---|---
   Solid| OK
   Flashing| Replace
   No light| Replace

2. STEP TWO
   Use screwdriver to remove screws and open

3. STEP THREE
   Use non-metallic object to push out.

WARNING!: The battery is hazardous and must be kept out of reach of children. The battery can cause severe or fatal injuries within 2 hours or less if swallowed or placed inside any part of the body. If you suspect the battery has been swallowed or placed inside any part of the body, SEEK IMMEDIATE medical attention.

SMART PHONE CONTROL

(Smart Pro & Smart Only)

The Smart Phone Control works via your home’s WiFi network.
Initial set up involves linking your phone app and smart opener to your home network.

WARNING!: This device allows for operation of the door when not in line- of-sight of the door and opener. The door may operate unexpectedly, therefore do not allow anything to stay in or near the path of the door

BEFORE YOU START

| | | |
---|---|---|---|---
Download the B&D App to your smartphone| | Ensure limits are set prior to connecting to wi‑| | The home WiFi router is within range of opener

1. STEP ONE
   | |
   ---|---|---
   Remove controls cover & Press repeatedly| | till network LED is lit
2. STEP TWO
   | |
   ---|---|---
   HOLD for 5 sec| | LED will turn PURPLE (HOTSPOT ON)
3. STEP THREE
   | |
   ---|---|---
   Go to phone settings, then WiFi and select (B&D000000)| | Open APP and click START
4. STEP FOUR
   | |
   ---|---|---
   Set up new Smart Hub in app| | Set up new Smart Hub in app
5. STEP FIVE
   | | | |
   ---|---|---|---|---
   Network LED and light will flash.| | Press| | Follow instructions in the app Network LED will turn Blue then return controls cover

TROUBLESHOOTING

Main Light = Service / Warning Indicator: Requirements for a service and user warnings are indicated after operation by the main light repeatable flashing OFF a number of times followed by a pause. The below table identifies the issues and remedies

| Issue| Remedy
---|---|---
1| Normal operation (door is fully open)
2| Normal operation (door is fully open)| Clear away any obstructions. Test Door. If unable to move the door and suspect beam is faulty, enter Safety Beam Emergency Close by pressing and holding a pre-coded transmitter button until the door closes.
3| Wireless Auto-Lock

battery is low

| Change Auto-lock battery
4| Wireless PE battery is low| Change PE Battery
5| Wireless Auto-Lock is not unlocked and preventing door moving| Check Auto- Lock, test by pressing emergency release button on the lock and the test door operation.
6| Maintenance is due after pre-set number of cycles.| Contact dealer to arrange service.
7| Standby battery is faulty| Contact 1300 769 850 within Australia for assistance.
8| Door was obstructed| Clear away any obstructions and test door opens/closes correctly. (if the door is damaged, contact a door professional)
9| Motor overloaded or stalled| Contact dealer to arrange a door service.
10| Unit running on battery power (Only available with SDO-7 & SDO-9| Main light will _ash (3) three times at the start of the cycle to indicate the opener is running  from battery backup and 10 _ashes at the end of cycle. Check power supply.

CARING FOR YOUR OPENER

Preventative servicing of your garage door and opener, is important. Your garage door is made up of numerous moving parts designed to lift and lower your door safely and efficiently.
Ongoing preventative servicing ensures that your door continues to function within factory specifications, greatly reduces the risk of failure and repair bills down the track and ensure you maintain your Warranty.
Refer to your Owners Opener Handbook for your service schedule available HERE.

Refer to the installation manual for monthly testing procedures in Section 13 to ensure garage door is fit for use available HERE.

Online warranty details are available HERE.

NEED A SERVICE CALL?

If the opener needs a service please call the dealer who installed the garage door opener (their contact details are usually on a sticker on the back of your garage door).

For product assistance, general enquiry or more information, please visit: bnd.com.au or call 13 62 63.

References

• B&D Garage Doors - Safe and Secure Australian Garage Doors - B&D Australia

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>