KAGA FEI EC2811 Bluetooth Low Energy Module User Manual

: June 13, 2024
: KAGA FEI

Table of Contents

KAGA FEI EC2811 Bluetooth Low Energy Module
FCC STATEMENTS
Pin Descriptions
Read User Manual Online (PDF format)
Download This Manual (PDF format)

KAGA FEI EC2811 Bluetooth Low Energy Module

Product Information

Product Name : EC2811
Manufacturer: KAGA FEI Co., Ltd.
FCC ID: 2A6NFEC2811
IC: 2 8568-EC2811
Version : 1.0
Date: 17-Aug.2023

FCC STATEMENTS

This module should be installed in the host device according to the interface specification.

Canada Regulatory Information
a) This device complies with Innovation, Science and Economic Development Canada’s applicable license-exempt RSSs. Operation is subject to the following two conditions:
- This device may not cause interference, and
- This device must accept any interference, including interference that may cause undesired operation of the device.
b) This product is certified as type of the portable device with Innovation, Science and Economic Development Canada Rules. To maintain compliance with RF Exposure requirement, please use within specification of this product.
c) Please notify certified ID by either one of the following methods on your product.
Specifiez ID certifiée dans vote produit par une de méthode suivante.
Contains Transmitter module IC : 28568-EC2811
Contains IC : 28568-EC2811
d) Please indicate your product name at any location on the exterior of the host product or product packaging or product literature, which shall be available with the host product or online.
e) Please include the following statements in rectangle on the user manual of the host device of this module;

This device complies with Innovation, Science and Economic Development Canada license-exempt RSS standards. Operation is subject to the following two conditions:

This device may not cause interference.
This device must accept any interference, including interference that may cause undesired operation of the device.

FCC Regulatory Information

a) This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions:
- This device may not cause harmful interference, and
- This device must accept any interference received, including interference that may cause undesired operation.
b) Please notify certified ID by either one of the following methods on your product.
- Contains Transmitter Module FCC ID: 2A6NFEC2811
- Contains FCC ID: 2A6NFEC2811
c) CAUTION: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
d) This product is certified as type of the portable device with FCC Rules. To maintain compliance with RF Exposure requirement, please use within specification of this product.
e) The antenna used for this transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
f) This module can change the output power depending on the circumstances by the application software which is developed by module installer. Any end user cannot change the output power.
g ) This device complies with part 15 of the FCC Rules. Part 15 Subpart C
h) The modular transmitter is only FCC authorized for the specific rule parts (Part 15 Subpart C) listed on the grant, and the host product manufacturer is responsible for compliance to any other FCC rules that apply to the host not covered by the modular transmitter grant of certification. The final host product still reguires Part 15 Subpart B compliance testina with the modular transmitter installed.
I) Co location of this module with other transmitters that operate simultaneously are required to be evaluated using the FCC multi transmitter procedures. When installing this module to your final devices, please make sure to carry out all the necessary evaluations according to the applicable guidelines like follows:
- for RF exposure: KDB 447498, KDB 996369 and any other relevant guidelines
- for EMC: KDB 996369 D04 and any other relevant guidelines
J) When you install this module to your final devices, please ensure that your final composite product complies with the applicable FCC rules in reference to a guidance in KDB 996369.
k) Antenna List
This module is approved along with the following antenna.
You cannot use any antennas other than the listed one because it deviates from the accredited conditions.Manufacturer| TAIYO YUDEN
---|---
Part No.| AH212M245001-T
Antenna Type| Monopole
Maximum Antenna Gain| +0.9dBi

Please include the following statements in rectangle on the user manual of the host device of this module;

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

This device may not cause harmful interference, and
This device must accept any interference received, including interference that may cause undesired operation.
FCC CAUTION: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
The antenna used for this transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
This product is certified as type of the portable device with FCC Rules. To maintain compliance with RF Exposure requirement, please use within specification of this product.
CE Regulatory Information
- a) When your end product installs this module, it is required to proceed additional certification processes before placing on the market in EU member states to make your products fully comply with relative EU standards.
- b) KAGA FEI can provide you the test reports of conducted measurement portion for the radio module. You can utilize the test reports for the certification processes of your end product as it requires radio testing.

Control No.

(1/2)

| Control name Pin Layout
---|---

Pin Descriptions

Pin	Pin name	Pin function	Description
1	DCC	Power	DC/DC converter output pin (built-in LC for DC/DC).
2	DEC4	Power	1V3 regulator supply decoupling.

Input from DC/DC converter. Output from 1.3 V LDO.

20

| P0.21 RESET| ****

Digital I/O

| General purpose I/O pin Configurable as system RESET pin.

(Factory default : General purpose I/O pin)

21| GND| Ground| Ground pin. (0 V)
22| OUT_MOD| RF In/Out| RF I/O pin. It should be connected to Pin 23 OUT_ANT for normal operation.
23| OUT_ANT| Antenna In/Out| Internal antenna. It should be connected to Pin 22 OUT_MOD for normal operation.
24| P0.22| Digital I/O| General purpose I/O pin.
25| P0.23| Digital I/O| General purpose I/O pin.
26| P0.24| Digital I/O| General purpose I/O pin.
27| P0.25| Digital I/O| General purpose I/O pin.
28| P0.26| Digital I/O| General purpose I/O pin.
29| P0.27| Digital I/O| General purpose I/O pin.
30| P0.28 AIN4| Digital I/O Analog input| General purpose I/O pin. SAADC/COMP input.
31| P0.29 AIN5| Digital I/O Analog input| General purpose I/O pin. SAADC/COMP input.
32| P0.30 AIN6| Digital I/O Analog input| General purpose I/O pin. SAADC/COMP input.
33| P0.31 AIN7| Digital I/O Analog input| General purpose I/O pin. SAADC/COMP input.
34| P0.02 AIN0| Digital I/O Analog input| General purpose I/O pin. SAADC/COMP input.
35| P0.03 AIN1| Digital I/O Analog input| General purpose I/O pin. SAADC/COMP input.
Pin| Pin name| Pin function| Description
---|---|---|---
36| P0.11| Digital I/O| General purpose I/O pin.
37| P0.12| Digital I/O| General purpose I/O pin.
38| P0.15| Digital I/O| General purpose I/O pin.
39| P0.16| Digital I/O| General purpose I/O pin.
40| P0.19| Digital I/O| General purpose I/O pin.
41| P0.20| Digital I/O| General purpose I/O pin.
42 to 47| GND| Ground| Ground pin. (0 V)