KAGA FEI EJ2832 Bluetooth Low Energy and ANT Module User Manual

: June 9, 2024
: KAGA FEI

Table of Contents

KAGA FEI EJ2832 Bluetooth Low Energy and ANT Module
Japan Regulatory Information
FCC
Pin Descriptions
Read User Manual Online (PDF format)
Download This Manual (PDF format)

KAGA FEI EJ2832 Bluetooth Low Energy and ANT Module

KAGA-FEI-EJ2832-Bluetooth-Low-Energy-and-ANT-Module-PRODACT-
IMG

This module should be installed in the host device according to the interface specification

Japan Regulatory Information

This Product is a radio system and o btained certification of construction type combined with the specific antenna.
Please ensure that your product has a label with the following certification mark at easily viewable location. If your product is too small to have the label, please place it i n the instruction manual and package of your product. The mark diameter shall be easily legible. In case your product does not have the label with the following certification mark, you or your customer who uses your product may be against the Radio Law and subjected to criminal punishment. K A G A F E I shall not be liable for any loss or damage incurred by you or your customer arising from use of your product which does not have following certification mark. This product ins talls a radio system which has been a pproved as a radio station in a low power data communication system based on the Radio Law. EJ2832 : 0 0 5 1 0 3 1 2 0

Canada Regulatory Information

The following information must be indicated on the host devic e of this module;
This device comp lies wit h Innovation, Science and Economic Development Canada’s applicable licence exempt RSSs. Operation is subject to the following two conditions:
This device may not cause interference e; and
This device must ACC ept any interference, including in terference that may cause undesired operatio n of t he device.
Le présent appareil est conforme aux CNR d’
Innovation, Sciences et Développement économique Canada applicables aux appareils rad io exempts de licence. L’exploi station est autorisée aux deux cond itions suivantes :
l’appareil ne doit pas produire de brouillage;
l’utilisateu r de l ’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d ’en compromettre le fonctionnem ent.
This product is certified as type of the portable device with Science and Economic
Development Canada Rules. To maintain compliance with RF Ex posure requirement,
please use within specification of this product Ce prod
uit est cert ifié comme type de l’appareil portable avec Règles de Innovation,
Sciences et Développement économique Canada . Pour maintenir l’acquiescement avec exigence Exposition de RF, veuillez utiliser da n s spé cifica tion de ce produit –
IC: 28568 EJ2832
Please notify certified ID by eith er one of the following metho d o n your product.
Contains I C : 28568 EJ2832
Specifiez ID c e r tifiée dans votre produit par une de méthode suivante. Co ntains IC : 28568 EJ2832

FCC

FCC Re gulatory Information

Th is device complies with part 15 of the FC C Rules. Part 15 Subpart C b
The following statement shall be indicated on the host device or the user manual of the host device; Operation is subject to the following t w o co n ditions: (1) This device may n ot cause harmful interference, and (2) th is device must accept any interference received, including interference that may cause undesired operation.
Please notify certified ID by either one of the following method o n y o ur product Conta ins Tra nsmitter Module FCC ID: 2A6 NF EJ283 2 Con tains FCC ID: 2A6NF EJ2832
Since there is no space which indicates FCC ID on this module, FCC ID is indicated in a manual. If the FCC ID is not visible when the module is installed inside another device, then the module is inst alled must also displa y a label referring to the enclosed module. e The following stateme nt shall be indicated in the user manual of the host device;
CAUTION: C hanges or modifications not expressly approved by the party respons ible for compliance could void the use’s authority to o perate the equipment. f
The modular transmitter is only FCC authorized for the specific rule parts ( Part 15 Subpart C ) listed on the grant, and the host produc t manufacturer is responsible for compli ance to any other F CC rules that apply t o the host not covered by the m odular transmitter grant of certifi cation. The final host product still requires Part 15
Subpart B compliance testing with the modular transmitte r installed.
This product is certified as type of the portable devic e wit h FCC Rules. To maintain compliance with RF Exposure requirem ent, please use within specification of this product
The following statement shall be indicated i n the user manual of the host device; Th e antenna used for this transmitter must not be co located or ope rating in conjunction with any other antenna or transmitt e r.
This module can change the output power depending on the circumstances by the application software which is developed by module installer . Any end user cannot change the output power. j ) Antenna List

No.1|
---|---
Antenna Category| Monopole
Antenna Type| PCB antenna
Dimensions| 3.45mm x 4.7mm

CE Regulatory Information

When yo ur end product instal ls this modu le, it is required to procee d additional certification processes before pla cing on the market in EU member states to make y our products fully comply with relative EU standards.
K A G A F E I can provide you the test reports of conducted measurement por tion for t he radio module. You can u t ilize the test reports for the certificatio n processes of your end product as it requires radi o testing.

Control No.

(1/2)

| Control name

Pin Layout

---|---

Pin Descriptions

Pin	Pin name	Pin function	Description
1	GND	Ground	Ground pin. (0 V)
2	P0.00

XL1

| Digital I/O

Analog input

| General purpose I/O pin.

Connection for 32.768kHz crystal (LFXO).

3| P0.01

XL2

| Digital I/O

Analog input

| General purpose I/O pin

Connection for 32.768kHz crystal (LFXO).

4| P0.28

AIN4

| Digital I/O

Analog input

| General purpose I/O pin.

SAADC/COMP/LPCOMP input.

Input from DC/DC converter. Output from 1.3 V LDO.

7| NFC1

P0.09

| NFC input

Digital I/O

| NFC antenna connection.

General purpose I/O pin.

8| NFC2

P0.10

| NFC input

Digital I/O

| NFC antenna connection.

General purpose I/O pin.

9| GND| Ground| Ground pin. (0 V)
10| P0.18

TRACEDATA[0]

| Digital I/O| General purpose I/O pin

Trace port output.

11| P0.20

TRACECLK

| Digital I/O| General purpose I/O pin.

Trace port clock output.

OUT_MOD for normal operation.

14| OUT_MOD| RF In/Out| RF I/O pin. It should be connected to Pin 13 OUT_ANT for

normal operation.

programming

18

| P0.21 RESET| ****

Digital I/O

| General purpose I/O pin

Configurable as system RESET pin. (Factory default : GPIO)

19| P0.08| Digital I/O| General purpose I/O pin.
20| GND| Ground| Ground pin. (0 V)
21| P0.06| Digital I/O| General purpose I/O pin.
22| P0.07| Digital I/O| General purpose I/O pin.
Pin| Pin name| Pin function| Description
---|---|---|---
23| P0.05

AIN3

| Digital I/O

Analog input

| General purpose I/O pin.

SAADC/COMP/LPCOMP input.

24| DCC| Power| DC/DC converter output pin.
25| P0.04

AIN2

| Digital I/O

Analog input

| General purpose I/O pin.

SAADC/COMP/LPCOMP input.

26| P0.03