XPOtool 51484 Tyre Wall Holder User Manual
- June 4, 2024
- XPOtool
Table of Contents
XPOtool 51484 Tyre Wall Holder
Introduction
Thank you for purchasing this quality product. To minimise the risk of injury
we urge that our clients take some basic safety precautions when using this
device. Please read the operation instruc-tions carefully and make sure you
have understood its content. Keep these operation instructions
safe.
Technical data
| Size (㎜) | 780–1370×730×705 |
|---|---|
| Width of holder (㎝) | 81–122 |
| Size of wheels (inch) | 12–18 |
| Max. number of wheels | 4 |
| Capacity (㎏) | 130 |
Assembly instructions
-
First install the two main parts of this folding tyre rack, as shown on the pho-tos on the right. Connect the upright support and horizontal support on their end with two little brackets, using two sets of M10×50 bolt and nut. You will get an L frame. Join the connecting long thin brackets using an M20 bolt and nut; af-terwards connect this part to the L frame, one end meeting the upright sup-port and the other end meeting the hor-izontal support. Please remember to put a M8 nut as a spacer between the bracket and the horizontal support. As-sembly the other main part, exactly like this first one.
-
Mounting the upright supports to the wall studs: Install 2 wall studs that are 32″ to 48″ apart (measured from their centre). Make sure the holes are on the same level of height. Pre-drill the 2 marked holes using a 3⁄16″ drill bit (M: 32″ to 48″ centres).
IMPORTANT NOTES:- a) The unit MUST be installed on wall studs. Do not use wall anchors for mounting directly to sheet rock.
- b) Do not overtighten the lag screws (max. 13,6 Nm/10 ft.lbs.). They only need to be fully seated.
-
Mount parts (1) and (2) with expan-sion screws (5) (not supplied due to dif-ferent standard). Do not fully tighten the top screws now. The brackets must be at the same level. Make the remaining two holes and fasten them with screws (5). Fully tighten all screws.
-
Attach the round tubes: Insert tubes (4) into tubes (3), fasten them to the brackets (1, 2) with bolts (6), in the position that best supports your tyres.
-
Tighten, adjust, and fold: All fasteners must be fully tightened. Store the unit in a folded position as shown.
The information contained in this document may alter at any time without previous notice. It is prohibited to copy or spread any parts of this document in any way without prior written allowance. All rights re-served. The WilTec Wildanger Technik GmbH cannot be held accountable for any possible mistakes in this operating manual, nor in the diagrams and figures shown. Even though, the WilTec Wildanger Technik GmbH has undergone biggest possible efforts to ensure that the operating manual is complete, faultless, and up to date, mistakes cannot be entirely avoided. If you should find a mistake or wish to make a suggestion for improvement, we look forward to hearing from you.
- Send an e-mail to: service@wiltec.info
- or use our contact form: https://www.wiltec.de/contacts/
- The most recent version of this manual in various languages can be found in our online shop via: https://www.wiltec.de/docsearch
- Our postal address is: WilTec Wildanger Technik GmbH Königsbenden 12 52249 Eschweiler
Germany
To return orders for exchange, repair, or other purposes, please use the
following address. Attention! To allow for a smooth execution of your
complaint or return, it is important to contact our customer service team
before returning the goods.
Returns Department
WilTec Wildanger Technik GmbH
Königsbenden 28
52249 Eschweiler
E-mail: service@wiltec.info
Tel: +49 2403 55592–0
Fax: +49 2403 55592–15
Important notice:
The reprint or reproduction, even of excerpts, and any commercial use, even in
part, of this instruction manual require the written permission of WilTec
Wildanger Technik GmbH.
https://www.XPOtool.com The Tool Experts
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>