MP GLOBAL SSXLLV600 SoundStep LV Flooring Underlayment Instruction Manual

June 12, 2024
MP GLOBAL

MP GLOBAL SSXLLV600 SoundStep LV Flooring Underlayment

All wood and concrete subfloors must be flat within 1/8″ over a 6′ span, or 3/16″ over a 10′ span. All areas must be checked prior to installation.

Instrucciones de instalaciön en espafiol: mpglobalproducts.com/SSLV- instaII
Transferrable lifetime warranty – mpgIobaIproducts.com/SSLV- warranty

GENERAL INFORMATION

Product may be installed over:

  • Double layer wood construction over joists or trusses up to 19.2″ on center
  • Single layer APA rated Sturd-l-FloorT&G, minimum 23/32″ over joists or trusses up to 19.2″ on center
  • APA approved underlayment grade plywood
  • Oriented strand board (OSB)
  • On, above or below grade concrete
  • Sound Gypsum based topping and lightweight concrete

Recommended Uses:

  • Residential applications on all grade levels
  • Floating, nail and glue down applications
  • Interior use in dry, heated areas.

Subfloor and Preparation:

  • All subfloors must be flat, clean, smooth and dry
  • Sand any rough surfaces and/or uneven joists
  • Fill any cracks on concrete or panel joints wider than 1 /8″ using a recommended patch/leveling product

INSTALLATION METHODS

Floating Floor Installation:

  • Be sure the subfloor is clean, smooth and free of dust and debris
  • Unroll the Underlayment and place embossed side down to the subfloor.
  • Make sure that underlayment seams run perpendicular (at right angle) to the long dimension of the planks.
  • Underlayment must be positioned with a minimum 4″ separation between seams of underlayment and seams of finished flooring products
  • Trim the perimeter edges of the Underlayment W’ from the wall
  • Butt seams together and seal using a good quality single faced tape
  • Install the floor covering product according to the manufacturer’s instructions

Double-Glued Installation:

  • Be sure the subfloor is clean and free of dust and debris
  • Unroll the Underlayment and place embossed side down to the subfloor.
  • Make sure that underlayment seams run perpendicular (at right angle) to the long dimension of the planks
  • Trim to fit the Underlayment into the target areas.
  • Move the trimmed-to-fit underlayment to the side to apply the adhesive
  • Apply a recommended pressure sensitive adhesive using the flooring manufacturer recommended trowel
  • Once the adhesive has flashed (dried to a tacky touch) place the trimmed-to-fit underlayment into the adhesive
  • Butt seams together and apply 2″ wide clear packaging tape centered over the seam
  • Roll the adhered Underlayment with a 100 lb flooring roller
  • Mark starting lines on Underlayment for placement of finished flooring product
  • Apply a recommended pressure sensitive adhesive using the flooring manufacturer recommended trowel
  • Once the adhesive has flashed (dried to a tacky touch) you can begin flooring installation according to the manufacturers recommendations
  • Make sure the staggered end joints fall at least 2″ away from the underlayment seams
  • Follow flooring manufacturer recommendations for expansion gaps and installing transitions in large span applications and doorways
  • Roll the finished floor with a 100 lb flooring roller
  • Be sure not to slide flooring into position which could potentially displace adhesive

Nail down hardwood (solid and engineered) Installation:

  • Be sure the subfloor is clean and free of dust and debris
  • Unroll the Underlayment and place embossed side down to the subfloor.
  • Install underlayment in opposite direction to the laminate or hardwood floor. Start in a corner and roll out underlayment, installing it flush to the walls.
  • Continue the next row in the same manner until the whole room is covered. You can tape the seams but it is not necessary.
  • Install the hardwood per manufactures written instructions. Install baseboard slightly off floor to avoid flanking path.

Trim and Molding:

  • All finish trim and transition moldings must be installed without binding or restricting the free movement of the above finished flooring products

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals