MECAN WT-05 Soundcard Digital Wireless Headphones User Manual

: June 13, 2024
: MECAN

Table of Contents

MECAN WT-05 Soundcard Digital Wireless Headphones
kindly reminder
Product overview
Product schemat (laorrain
Kev operation instructions
A dirty and a schematic
instructions for the pair code
matters need attention
Specification parameters
Warranty Card
CONTACT
Read User Manual Online (PDF format)
Download This Manual (PDF format)

MECAN WT-05 Soundcard Digital Wireless Headphones

kindly reminder

Thank you for using the company’s digital wireless listening equipment, in order to let you easily experience the product, we randomly equipped with detailed instruction manual, you can get the function of the product and use method knowledge before you start using this, please read this manual, so that you can use the machine correctly, if there is any printing error or omissions hope the users understanding, when the content changes, without prior notice.

Note: Before the first use, please charge for 4 hours first.

Product overview

Using UHF, digital chip, lower than 1 mS transmission delay, automatic ID lock frequency anti-interference Strong ability, the transmission signal is more reliable, more stable, clear timbre. Automatic scan frequency pairing function, more convenient and simple to use. 3.5 Audio line is widely used in all kinds of audio and audio equipment.
The chip comes with low power prompt and low power shutdown function (key operation instructions, Indicator light part).
Using digital circuit processing technology, with a higher signal-to-noise ratio.
The U-segment frequency is more penetrating, more stable, and pure in timbre.
Can support multiple uses without interference (see instructions for details).
Can support one-to-many, one-to-one mode respectively

Note: One-to-many support for open mode: one launch, can be multiple simultaneous reception; One_to-one is private as described later

Product schemat (laorrain

A, ejector:

Long press the power button to turn on / off.
Short press the power button function switch: current channel (C number) or volume (U number) when the channel is displayed: press + or-key, will change the current channel, a total support CO1~ C30. When the volume is displayed: press + or-key, will change the current volume, total support U00~U09.
Mute operation: long press the + and-keys at the same time, and the screen flashes (000) to indicate that entering the mute state, press any key to remove the mute.
One-to-many setting method: in the shutdown state, first press the transmitter-key, then long press the power button to power on until OP (OPEN) is displayed, and the corresponding blue light is lit.
One-to-one setting method: when shutdown, first press the transmitter button, and then long press the power button to power, until the CLS (CLOSE description), the corresponding blue light out, or refer to the following code / connection instructions (as long as you enter the pairing mode, automatically enter the one-to-one mode. blue light out)

Note (indicator part):

Charging indicator description: charging red light on, full red light out;
Blue light on: one-to-many mode; blue light out: one-to-one mode;
Green light: normal light in normal hours, low power flash, please charge in time;
The screen displays as follows: the current frequency point of C 01 30, a total of 30 frequency points; U 00 U 09 a total 9 level volume adjustment;
—-On the frequency.

Kev operation instructions

B, acceptor:

Long press the power button to turn on / off.
Short press the power button function switch: current channel (C number) or volume (U number) when the volume is displayed: press + or key, will change the current volume, a total support U 00 ~ U 09.
- a . In one-to-many manual mode: when the channel is displayed: press + or key, the current channel will be manually changed, supporting C 01 ~ C30.
- b. In one-to-one automatic mode, the valid channel is automatically tracked, and pressing + or key cannot change the current channel.
One-to-many manual mode: In the shutdown state, press the + button of the receiver, and then press the power button to start the power on until OP (OPEN) is displayed, and the corresponding blue light is lit.
4. One-to-one automatic mode setting method: in the
shutdown state, first press the + key of the receiver,
and then long press the power key to start the power,
until the corresponding blue light of CLS (CLOSE) goes
out.

Note (indicator part):

Charging indicator instructions: charge the red light is on, and fill the red light out.
Blue light on: one -to-many mode, blue light out: one-to-one mode.
Green light: valid signal received; green light out no valid signal received.
When the power is low, the blue light will flash. Please charge in time.

A dirty and a schematic

One drag multiple schematic diagram

instructions for the pair code

One to-one mode:

Please shut down the transmitter and receiver, pick up the transmitter, hold the + -key and long press the power button screen will display ON, don’t release three buttons until the screen fast run (- – – into the code state), loosen the button, immediately open the receiver, such as the transmitter display running end, the receiver green light, said pairing complete, otherwise pairing failure, need to shut down, to the code.
One-to-many mode: the launch / receiver into one- to-many mode, receiving / transmitter blue light at the same time (reference key instructions: A transmitter item 4 + B receiver item 3), through the short button can view their current working channel, by pressing + or key to
Make them work in the same channel, if the receiver green light. said into the effective channel.

Note:

Set up the transmitter first and then set up the receiver.
After the successful connection, adjust the transmitter channel, and the receiver will jump to this channel synchronously.

matters need attention

Note: (One-to-one mode is applicable)

A. At the end of the code, we must turn off the non- associated equipment and continue to set the next set of code according to the above operation method.
B. When multiple channels are used simultaneously, the same channel should be avoided. If the sound is disturbed (with noise), try other channels (see the key operation instructions).
C. When the two devices, please keep as close as possible If the code is not successful please repeat Repeat operation, because the effective time of the
code is only 10 seconds after the boot, so the code must
be used before the shutdown, if not the shutdown
directly operate the code, there will be the following
problems;
- is not connected, the receiver green light flashing.
- can connect, but after shutdown, restart, receive blue light flash, the connection does not appear the above situation need to press the correct operation method code.
D, the factory has set the frequency band, such as the wrong operation of the frequency band, the connection is not please contact the seller, the seller send video to won hack to the origina frequency