MERIDIAN 55 Inch Outdoor Presenza Instruction Manual

: June 13, 2024
: MERIDIAN

Table of Contents

MERIDIAN 55 Inch Outdoor Presenza
Product Information
Product Usage Instructions
55” Outdoor Presenza Installation
Corporate Headquarters
Read User Manual Online (PDF format)
Download This Manual (PDF format)

MERIDIAN 55 Inch Outdoor Presenza

MERIDIAN 55 Inch Outdoor Presenza-PRODUCT

Product Information

The 55 Outdoor Presenza is a kiosk designed for outdoor use. It is not a free- standing design and requires mounting at all times. The kiosk features a front door, a monitor housing, and various connection points for antenna wires and power supply.

MeridianKiosks.com is the manufacturer of this product. Meridian promises a level of quality that goes beyond the expected, controlling every step of the process from concept to completion. The company’s processes are ISO 900 certified, and many of their
products can be UL Listed through UL self-certify.

Product Usage Instructions

Unpack the kiosk and remove the wrapping.
Place lifting chains or straps through the two lifting eye bolts on the top of the kiosk.
Ensure the kiosk is sufficiently supported using the lift points provided before removing any fittings securing it to the pallet.
Use the supplied key to unlock the side lock by turning it clockwise until it stops.
While keeping pressure to the right, pull out the key and tumbler.
Install the t-handle supplied with the kiosk by inserting it and turning counterclockwise to open the front door.
Once the front door is open, remove the four bolts holding it down to the pallet.
Lift the kiosk and set it into position over existing concrete sleeve anchors or preferred hardware.
Install washers and nuts and tighten them according to your local code specifications.
If slight leveling is needed, do this before tightening down the nuts.
Route antenna wires down through the cable ducting in the rear of the chassis and then across and up into the rear of the monitor pan and into the cradle.
Remove the lower power cover panel located in the bottom center of the chassis by unscrewing the single nut at the lower edge.
Run the incoming 120VAC 20-amp circuit up through the bottom of the kiosk and through the water-tight cord grip located on the left side.
Continue wiring up the back wall and into the disconnect located behind the electrical covering.
Locate the red-handled clamps on the right side and turn them counterclockwise to allow the rear monitor pan to swing out.
Pull the monitor pan outward until it stops to access all items and connections behind the monitor.
When closing the monitor housing, ensure that the lower right edge contacts a roller that will guide it into the correct location.
Once in the correct location, rotate the two red clamps clockwise to lock the housing to the rear surface.
Verify that all services are working, then close the monitor housing and lock it into position.
Close the front door, ensuring that the t-handle is turned in the correct direction to allow the locking arms to pull inward.
Ensure there is enough room for the door to close and for the locking bars to clear the bar system.
Push the door against the rear chassis and turn the t-handle to lock in the locking bars and rollers.
Insert the previously removed key and tumbler, turn it to the right (clockwise) until fully seated, and then turn counterclockwise.
Remove the key from the lock, and your kiosk is now ready for use.

55” Outdoor Presenza Installation

After unpackaging the wrapping on the kiosk, place lifting chains or straps thru the two lifting eye bolts on the top of the kiosk.

Ensure you have suﬃciently supported the kiosk using the lift points provided prior to removing any ﬁtting used to secure to pallet. This is critical as this unit is not a free standing design and requires mounting at all times.
Using the supplied key, place into the side lock and turn clockwise until it stops.
While keeping pressure to the right, pull out key and tumbler. With this removable key tumbler out, you can now install the t-handle supplied with the kiosk.
Insert the t-handle and turn counterclockwise to open the front door.
Once the front door is open, remove the four bolts holding this down to the pallet.
Once these are removed you can lift the kiosk and set into position over your existing concrete sleeve anchors (or your preferred hardware).
Once down in position, install the washers and nuts and tighten to your local code specs.
If slight leveling is needed, do this prior to tighten down the nuts.
Once the kiosk is fully tightened down, remove the lifting device along with the lifting eye bolts.
Place the supplied antenna cap on the top with the studs facing donward into the kiosks.
Place the antenna cabling and stud down thru the center holes in the topper.
Install the supplied hardware and tighten down the two topper studs and secure the antenna nut.
These will clamp the topper down to prevent water seeping into the opening for lifting.
Route antenna wires down thru the cable ducting in the rear of the chassis and then across and up into the rear of the monitor pan and into cradle. Remove the lower power cover panel located in the bottom center of the chassis.
This cover can be removed via the single nut located at the lower edge of this panel.
Run incoming 120VAC 20-amp circuit up thru the bottom of the kiosk and thru the water-tight cord grip located on the left side.
Continue wire up back wall and into the disconnect located behind the electrical covering.
Locate the red handled clamps o the right side and turn counterclockwise to allow rear monitor pan to swing out.
Pull this outward until it stops to access all items and connection behind the monitor.
When closing this monitor housing, the lower right edge will contact a roller that will guide this into the correct location.
Once there, rotate the two red clamps clockwise, locking housing to the rear surface.
Once all services are veriﬁed and working, close the monitor housing and lock into position. Then close the front door.
When closing the front door, make sure the t handle is turned the correct direction to allow the locking arms to pull inward.
This allow enough room for the door to close and the locking bars to clear the bar system.
Once the door is pushed against the rear chassis, turn the t handle to locking in the locking bars and rollers.
With the previously removed key and tumbler, insert and turn to the right (clockwise) again until it is fully seated and then turn counterclockwise.
Remove key from lock and your kiosk is now ready for using.

QUALITY + CERTIFICATION
Meridian promises a level of quality that goes beyond the expected. We control every step of our process from concept to completion, overseeing quality, design, cost and timelines. Many of our products can be UL Listed through UL self-certify and our processes are ISO 900