JBC T210-A Precision Handles, General Purpose Handles, Heavy Duty Handles Instruction Manual

JBC T210-A Precision Handles, General Purpose Handles, Heavy Duty Handles Instruction Manual

This manual corresponds to the following references:

Precision Handles:

• T210-A –
• T210-PA
• T210-NA

General Pupose Handles

• T245-A
• T245-GA
• T245-PA
• T245-NA

Heavy DutyHandles

• T470-A
• T470-SA
• T470-ZA
• T470-FA
• T470-MC
• T470-NA

Packing List

The following items are included:

Handle ____1 unit
according to purchased reference

Grips for Handles __ 1 unit
already asembled, according purchased handle reference

Sealing Plug for Handles _____ 1 unit
already asembled, according purchased handle reference

Manual_____ 1 unit
Ref. 0028966

Features – T210 Precision Handles

T210 Handles are suitable for precision soldering jobs with medium power requirements. Due to their size, they are ideal for conventional or small SMD soldering jobs, even under a microscope. They come with soft foam grip to ensure a better manual control of the tool and a greater comfort when working.

T210 Handles are supplied with 1.5 m cable length and work with C210 cartridges (not included)

T210 Precision Handle
Ref. T210-A

T210P Blue-Grip Precision Handle
Ref. T210-PA

T210P Handles are designed with blue grip handle for easy differentiation from other handles, e.g. when leaded and unleaded solder wire are used.

T210N Nitrogen Precision Handle
Ref. T210-NA

T210N Handles are designed to work in an oxygen-free atmosphere and so providing a better soldering quality. They offer extra heat to the solder joint and help prevent oxidation.

Note: JBC’s GN Nitrogen Generator Module or an external nitrogen feed is needed.

Features – T245 General Purpose Handles

T245 Handles are suitable for both, SMD components and soldering jobs with high power requirements (e.g. ground plane soldering).

Some models come with soft foam grip to ensure a better manual control of the tool and a greater comfort when working and in addition provides thermal insulation.

T245 Handles are supplied with 1.5 m cable length and work with C245 Cartridges (not included)

T245 General Purpose Handle
Ref. T245-A

T245G General Purpose Handle with Reinforced Cable
Ref. T245-GA

T245P Blue-Grip Handle
Ref. T245-PA

T245P Handles are designed with blue grip handle for easy differentiation from other handles, e.g. when leaded and leadfree solder wire are used.

The following soft foam grip as replacement are avialable: green T6057, blue T1528, black T1530.

T245N Nitrogen General Purpose Handle
Ref. T245-NA

T245N Handles are designed to work in an oxygen-free atmosphere and so providing better quality soldering. They offer extra heat to the solder joint and help prevent oxidation.

Note: JBC’s GN Nitrogen Generator Module or an external nitrogen feed is needed

Features – T470 Heavy Duty Handles

T470 Handles are suitable for intensive soldering jobs requiring high power delivery such as power electronics components soldering, large coax cable soldering, metal sheet soldering, etc.

They are available with grips of several shapes and materials, as well as different cable lengths (see below).

T470 Handles feature a set screw to secure the cartridge within the handpiece preventing its rotation.

T470 Heavy Duty Handle (1.5 m / 4.92 ft cable)
Ref. T470-A
T470S Heavy Duty Handle (3 m / 9.84 ft cable)
Ref. T470-SA

T470F Thermal Insulator Grip HD Handle (1.5 m / 4.92 ft cable)
Ref. T470-FA
T470M Thermal l Insulator Grip HD Handle (3 m / 9.84 ft cable)
Ref. T470-MC

T470Z Tri-Lobed Grip HD Handle (1.5 m / 4.92 ft cable)
Ref. T470-ZA

T470N Nitrogen HD Handle (1.5 m / 4.92 ft cable)
Ref. T470-NA
T470N Handles are designed to work in an oxygen-free atmosphere and so providing better quality soldering. They offer extra heat to the solder joint and help prevent oxidation.

Note: JBC’s GN Nitrogen Generator Module or an external nitrogen feed is needed.

Changing Cartridges – T210 and T245 Handles

JBC’s tool stand ADS, for T210 and T245 Handles, comes with quick tip changer. Save time and change cartridges safely without switching the station off. Be careful, the cartridges

may be hot, when placing them in the cartridge holder.

1. Removing
   
   Place the cartridge in the extractor and pull the handle to remove it.

2. Inserting
   
   Place the handle on top of the new cartridge and press the handle down.

3. Fixing
   
   Depending on the shape of the tip, use one of the holes for fixing the cartridge

Note: It is essential to insert the cartridge as far as the mark for a proper connection.

Changing Cartridges – T470 Handles

1. Removing
   
   Loosen the handle screw. Place the soldering iron with the cartridge in the extractor and pull the handle to remove it.

2. Inserting
   
   Place the handle on top of the new cartridge and press the handle down until the cartridge is fully seated.

3. Fixing
   
   Tighten the handle screw.
   Note: Prior to tightening the handle screw, make sure that the mark on the cartrige is aligned with the handle (see picture) to ensure a proper cartridge connection.

Changing Nitrogen Nozzles

If the outer cartridge diameter D1 is smaller than the inner nozzle diameter D2, the nozzle can be removed without removing the cartridge.

When the nozzle is hot, use pliers to remove the nozzle.

If the outer cartridge diameter D1 is larger than the inner nozzle diameter D2. The cartridges must be removed first before the nozzle can be removed. For T470 Handle loose the screw and remove the cartrige. Afterwards de nozzle can be removed.

When the nozzle is hot, use pliers to remove it.

To insert a new cartridge proceed as described on page 7.

Cartridge Range

JBC offers for each handle different cartridge types. Find the model that best suits your soldering needs at www.jbctools.com.

T210 Handles work with C210 Cartridges, T245 Handles work C245 Cartridges and T470 Handles with C470 Cartridges.

• Conical

• Chisel Conical

• Bent

• Bevel Special

• Models

Changing Grips*

Replace the soft foam grips easily using slip-on tabs. Note: Choose the correct grip depending on your handle model

1. Inserting Tabs
   
   Put the slide-on tabs into the  Repla

2. Inserting Grip
   
   Push the grip with the tabs onto the handle.

3. Removing Tabs
   
   Hold the grip and pull the tab. Use pliers if necessary.

Replacing Sealing Plugs

The sealing plug prevents undesirable flux vapors or particles from entering the tool. Its usage is highly recommended for intensive applications when soldering is exposed to FOD environments or for applications where the soldering iron works close to a vertical position.

Note: Choose the correct sealing plug depending on your handle model

1. **Removing Sealing Plug

** Enter a small shaft or screwdriver, not deeper than 8mm, and lift and pull the sealing plug. Never use a cartridge to do this

2. **Mounting Position

Note:** The chamfered side has to be positioned towards the handle.

3. **Inserting Sealing Plug

** Push the sealing plug inside the handle until the sealing plug  and handle edges are aligned.

Accessories

Compatibility

| Compact
Stations| Modular System
---|---|---
Handle| Cartridge
Range| CD| Stand| DI| DDE| DME| HDE
T210| C210| | ADS| | | |
T210P| | | | |
T245| C245| | | | |
T245G| | | | |
T245P| | | | |
T470| C245| | ADS| | | |
C470| | HDS| | | |
T470S| C245| | ADS| | | |
C470| | HDS| | | |
T470F| C245| | ADS| | | |
C470| | HDS| | | |
T470M| C245| | ADS| | | |
C470| | HDS| | | |
T470Z| C245| | ADS| | | |
C470| | HDS| | | |
T210N•| C210| | DNS| | | |
T245N•| C245| | | | |
T470N•| C245| | | | |
C470| | | | |

The MNE Nitrogen Flow Regulator is required. Use the proper nozzle according to the cartridge.

Maintenance

• Before carrying out maintenance, always unplug the stand and the tool.
• Check periodically that the metal parts of the tool and the stand are clean to ensure detection of the tool when it is in the stand. Use a damp cloth or alcohol.
• Periodically check all cables and tubes connections.
• Replace any defective or damaged pieces. Use original JBC spare parts only.
• Repairs should only be performed by a JBC authorized technical service

Safety

It is imperative to follow safety guidelines to prevent electric shock, injury, fire or explosion.

• Do not use the units for any purpose other than soldering or rework. Incorrect use may cause fire.
• Do not work on electrically live parts.
• The tool should be placed in the stand when not in use in order to activate the sleep mode. The soldering tip, the metal part of the tool and the stand may still be hot after the station is turned off. Handle with care, including when adjusting the stand position.
• Do not leave the appliance unattended when it is on.
• Avoid flux coming into contact with skin or eyes to prevent irritation
• Be careful with the fumes produced when soldering.
• Keep your workplace clean and tidy. Wear appropriate protection glasses and gloves when working to avoid personal harm.
• Utmost care must be taken with liquid tin waste which can cause burns.
• This appliance can be used by children over the age of eight as well as persons with reduced physical, sensory or mental capabilities or lacking experience provided that they have been given adequate supervision or instruction concerning use of the appliance and understand the hazards involved. Children must not play with the appliance.
• Maintenance must not be carried out by children unless supervised.

T210
Precision Handles
Ref. T210-A
Ref. T210-PA , Blue-Grip
Ref. T210-NA, Nitrogen

Net Weight:
56.8 g / 0.013 lb
56.8 g / 0.013 lb
93 g / 0.013 lb

Package Weight:
106.5 g / 0.031 lb
106.5 g / 0.031 lb
165 g / 0.031 lb

T245
General Purpose Handles
Ref . T245-A
Ref. T245-GA , Reinforced Cable
Ref. T245-PA , Blue-Grip
Ref. T245-NA , Nitrogen

T245 General Purpose Handles
Ref. T245-A| 66 g / 0.146 lb| 115 g / 0.254 lb
Ref. T245-GA, Reinforced Cable| 66 g / 0.146 lb| 115 g / 0.254 lb
Ref. T245-PA, Blue-Grip| 63.8 g / 0.141 lb| 114.7 g / 0.253 lb
Ref. T245-NA, Nitrogen| 93.2 g / 0.205 lb| b 93.2 g / 0.205 lb 1
470 Heavy Duty Handles
Ref. T470-A| 89.6 g / 0.198 lb| 140.5 g / 0.310 lb
Ref. T470-SA, 3m / 9.84ft cable| 140.3 g / 0.309 lb| 190.9 g / 0.421 lb
Ref. T470-FA, Thermal Insulator Grip| 90.7g / 0.200 lb| 140.6 g / 0.310 lb
and 3m / 9.84ft cable| 137.8 g / 0.304 lb| 188.6 g / 0.416 lb
Ref. T470-ZA, Tri-Lobed Grip| 90 g / 0.198 lb| 140 g / 0.309 lb
Ref. T470-NA, Nitrogen| 93 g / 0.205 lb| 165 g / 0.364 lb

For T245-NA and T470-NA:
– Package Dimensions: 277 x 73 x 50 mm
(L x W x H) 8.94 x 2.87 x 1.97 in

For T470-MC:
– Package Dimensions: 145 x 18 x 18mm
(L x W x H) 5.71 x 0.71 x 0.71 in

For all other handles:
– Package Dimensions: 235 x 40 x 40mm
(L x W x H) 9.25 x 1.57 x 1.57 in

Complies with CE standards
ESD safe

Warranty
JBC’s 2 year warranty covers this equipment against all manufacturing defects, including the replacement of defective parts and labour. Warranty does not cover product wear or misuse. In order for the warranty to be valid, equipment must be returned, postage paid, to the dealer where it was purchased

This product should not be thrown in the garbage. In accordance with the European directive 2012/19/EU, electronic equipment at the end of its life must be collected and returned to an authorized recycling facility

www.jbctools.com

References

• JBC Soldering Stations, Irons and Rework equipment for electronics

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>