SiHi SPK13 Cordless Impact Drill User Guide

: August 13, 2024
: SIHI

Table of Contents

Safety Information
Safety Information For Paint Spraying
Operating Pressure Vessels
Documents / Resources
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)

SiHi SPK13 Cordless Impact Drill

SiHi SPK13 Cordless Impact Drill

Safety Information

Important! The following basic safety actions must be taken when using this compressor in order to protect the user from electric shocks and the risk of injury and fi re. Read and follow these instructions before using the equipment.

Keep your work area tidy
Untidy work areas can result in accidents.
Check the ambient conditions
Do not expose the compressor to rain. Never use the compressor in damp or wet locations.
There is a risk of electric shock! Provide good lighting. Do not use the compressor near flammable liquids or gases. There is a risk of explosion!
Protect yourself against electric shocks
Avoid bodily contact with earthed parts, e.g.
pipes, radiators, cookers and refrigerators.
Keep children away!
Do not allow other persons to touch the compressor or cable, keep them away from your work area.
Keep your compressor in a safe place
When unused, the compressor must be stored in a dry, locked room out of children’s reach.
Do not overload your compressor
It will run better and safer within its quoted capacity range.
Wear suitable work clothes
Never wear loose fitting clothes or jewellery.
They may get caught in moving parts. Rubberg loves and non-slip shoes are recommended when working outdoors. Wear a hair net if you have long hair. Risk of injury!
Do not use the cable for purposes other than that for which it is designed
Do not carry the compressor by its cable and do not use the cable to pull the plug out of the socket. Protect the cable from heat, oil and sharp edges. The cable/plug could become damaged.
Take care of your compressor
Keep your compressor clean in order to work well and safely. Follow the maintenance instructions. Check the power plug and cable on a regular basis and have them replaced by an authorized specialist if they are damaged.
Check the extension cable regularly and replace it if damaged.
Pull out the power plug
When not in use and before carrying out any maintenance work.
Avoid unintentional starting
Make sure that the switch is turned off when connecting to the power supply.
When using an extension cable outdoors
Check that it is approved for outdoor duty and is marked accordingly.
Be alert at all times
Watch what you are doing. Use common sense when working. Never use the compressor when you are distracted.
Check your compressor for damage
Before using the compressor again, carefully check the safety devices and any slightly damaged parts to ensure that they are in good working order. Check that the moving parts are working correctly, that they do not jam, and that no parts are damaged. Make sure that all parts are fitted correctly to ensure that the equipment remains safe to use. Unless otherwise stated in the operating instructions, damaged guards and parts have to be repaired or replaced by a customer service workshop. Damaged switches have to be replaced by a customer service workshop.
Never use an electric power tool with a switch that cannot be turned on and off.
Important!
For your own safety you must only use the accessories and additional units listed in the operating instructions or recommended or specified by the manufacturer. The use of mounted tools or accessories other than those recommended in the operating instructions or catalog may place your personal safety at risk.
Leave all repairs to a qualified electrician
Repairs must be left strictly to qualified electricians or the user might suffer an accident.
Noise
Wear ear muffs when you use the compressor.
Replacing the power cable
To prevent hazards, leave the replacement of damaged power cables strictly to the manufacturer or a qualified electrician. There is a risk of electric shock!
Inflating tires
Directly after inflating tires, check the pressure with a suitable pressure gauge, for example at your filling station.
Roadworthy compressors for building site operations
Make sure that all lines and fittings are suitable for the maximum permissible operating pressure of the compressor.
Place of installation
Set up the compressor on an even surface.
Warning! Use the compressor only when all safety devices are in good working order. Never use it when you are under the influence of alcohol, drugs or sleep-inducing medication.
Keep the ventilation grilles clean at all times, particularly in dirty working environments.
Never use a defective compressor. Avoid operation if you notice anything abnormal such as unusual noises or excessive vibrations; switch off the machine and contact the service center.
Use only original parts; using non-original parts might cause the warranty to be voided and increase the risk of malfunctions. It is prohibited to make changes to the compressor repairs must be carried out by an approved service center.
Do not touch any hot parts and do not switch off the compressor by means of the connection cable.
The compressed air cycle should be performed only with suitable equipment capable of withstanding the maximum operating pressure.
The air produced is suitable neither for breathing nor for processing food.
ONLY AIR: This compressor is designed only for air, not for any other gases.
Clean the compressor and carry out its maintenance on a regular basis as described in the instructions; keep it dry and free of oil.
Do not move the compressor with the help of the air hose; release the pressure before transporting.

Safety instructions for working with compressed air and blasting guns

The compressor pump and lines can become very hot during operation. Touching these parts will burn you.
The air which is sucked in by the compressor must be kept free of impurities that could cause fires or explosions in the compressor pump.
When releasing the hose coupling, hold the hose coupling piece with your hand. This way, you can protect yourself against injury from the rebounding hose.
Wear safety goggles when working with the blow-out pistol. Foreign bodies or blown off parts can easily cause injuries.
Do not blow at people with the blow-out pistol and do not clean clothes while being worn.
Risk of injury!
Wear safety goggles and a respiration mask while working with the compressed air gun.
Dust is harmful to your health!

Safety Information For Paint Spraying

Do not process any paints or solvents with a flash point below 55° C. There is a risk of explosion!
Do not heat up paints or solvents. There is a risk of explosion!
If hazardous liquids are processed, wear protective filter units (face guards). Also, adhere to the safety information provided by the manufacturers of such liquids.
The details and designations of the Ordinance on Hazardous Substances, which are displayed on the outer packaging of the processed material, must be observed. Additional protective measures are to be undertaken if necessary, particularly the wearing of suitable clothing and masks.
Do not smoke during the spraying process and/or in the work area. There is a risk of explosion! Paint vapors are easily combustible.
Never set up or operate the equipment in the vicinity of a fire place, open lights or sparking machines.
Do not store or eat food and drink in the work area. Paint vapors are harmful to your health.
The work area must exceed 30 m3 and sufficient ventilation must be ensured during spraying and drying. Do not spray against the wind. Always adhere to the regulations of the local police authority when spraying combustible or hazardous materials.
Do not process media such as white spirit, butyl alcohol and methylene chloride with the PVC pressure hose. These media will destroy the pressure hose.
While filling, always keep sprayers away from the compressor in order to avoid contact with liquids.
The work area must be clearly separated from the compressor in order to prevent direct contact with the medium you are working with.
Keep a minimum distance of 2.50 m between the compressor and the compressed air tools/connections during operation.
Never point sprayers in the direction of the compressor.

Operating Pressure Vessels

You must keep your pressure vessel in good working order, operate the vessel correctly, monitor the vessel, carry out necessary maintenance and repair work immediately and meet the relevant safety precautions.
The supervisory authority may enforce essential control measures in individual cases.
A pressure vessel is not allowed to be used if it has faults or deficiencies that can endanger workers or third parties.
Check the pressure vessel for signs of rust and damage each time before using. Do not use the compressor with a damaged or rusty pressure vessel. If you discover any damage, then please contact the customer service workshop.

Do not lose these safety instructions.