EIBENSTOCK EBS 120.1 Concrete Grinder Instruction Manual

EIBENSTOCK EBS 120.1 Concrete Grinder

Product Information

The product is a Concrete Grinder, model EBS 120.1. It has a power input of 1400 W and operates at a rated voltage of 230 V~. The grinder is equipped with a diamond grinding disc and is suitable for various applications such as working on concrete, bricks, limestone, basalt, and sandstone. It comes with different types of diamond grinding discs for different purposes, including standard concrete, premium concrete, screed, and Rapid K. The grinder is designed to be used with an industrial vacuum cleaner for dust extraction.

Product Usage Instructions

1. Before operating the machine, read the user manual carefully.
2. Ensure a clean and safe working environment.
3. Take necessary precautions to protect yourself, including wearing safety goggles, dust masks, and protective gloves.
4. Make sure the electrical connection is properly done according to the specified voltage (110V or 230V).
5. To turn on the grinder, use the switch with a safety lock to prevent accidental activation.
6. Select the appropriate diamond grinding disc based on the desired application (concrete, screed, or Rapid K).
7. During operation, follow proper grinding techniques and guidelines.
8. Prior to performing any maintenance or repair work, always disconnect the power plug.
9. Refer to the user manual for detailed maintenance instructions.

Please note that these usage instructions are a summary. For complete information and safety guidelines, refer to the provided user manual.

Important Safety Instructions

Important instructions and warning notices are allegorized on the machine by means of symbols:

• Before you start working, read the operating instructions of the machine.
• Work concentrated and carefully. Keep your workplace clean and avoid dangerous situations.
• In order to protect the user, take precautions.

During work, you should wear ear protectors, goggles, dust mask, protective gloves, and sturdy work clothes!

• Use ear protection
• Wear safety goggles
• Wear a dust mask
• Wear protective gloves

Warning notices

• Warning of general danger
• Warning of dangerous voltage
• Warning of hot surface
• Danger of being ripped or cut

Technical Data

Concrete Grinder EBS 120.1

Available special accessories:

Diamond Grinding Wheel
Type| Colour|
Concrete standard| gold, sand| 37114000
Concrete premium| gold, sand| 37102000
Screed| yellow| 37103000
Rapid K| blue| 37110000

Brush rim (2-part)| 3722A000
Industrial Vacuum Cleaner ESS 35 MP| 09931000
Industrial Vacuum Cleaner DSS 35 M iP| 09919000

For further information about our products and our wide range of accessories please see: www.eibenstock.com

Content of Delivery
Concrete grinder with a diamond grinding wheel (concrete), tool kit, and operating instructions in a case

Intended Use
The concrete grinder is intended for professional use. With an appropriate grinding wheel, the tool may be used for smoothing rough concrete, removing mold seams, residual mud, joint fillers and tile adhesives. The machine may be used exclusively in conjunction with a diamond cup wheel and a vacuum cleaner of dust category M. Only use grinding wheels recommended by the manufacturer. These have a small weight and a high concentricity. Using other grinding wheels can cause an overload of the machine or damage of the bearings and danger to the user.

Safety Instructions

Safe work with the machine is only possible if you read this operating instruction completely and follow the instructions contained strictly. Additionally, the general safety instructions of the leaflet supplied with the tool must be observed. Prior to the first use, the user should absolve a practical training. Save all warnings and instructions for future reference.

If the mains cable gets damaged or cut during the use, do not touch it, but instantly pull the plug out of the socket. Never use the tool with damaged mains cable.

The tool must neither be wet nor used in a humid environment.

• Do not use the tool in an environment with danger of explosion.
• Do not drill into asbestos-containing materials.
• Modifications of the tool are prohibited.
• Never use the machine without dust guard. Use machine with partly removed dust guard in corners only. For other applications the dust guard must always be closed.
• Always check the tool, cable and plug before use and plug before use. Have damages only repaired by specialists. Insert the plug into the socket only when the tool switch is off.
• When you work outside, the machine has to be used with a faultcurrent circuit breaker with max. 30 mA.
• The machine should only work under supervision of somebody. Plug and switch the machine off if it is not under supervision, in case of putting up and stripping down the machine, in case of voltage drop or when fixing or mounting an accessory.
• Switch the machine off if it stops for whatever reason. You avoid that it starts suddenly and not under supervision.
• Don’t use the machine if a part of the housing is damaged or in case of damages on the switch, the cable or plug.
• Pay attention that the speed indicated on the grinding wheel meets or is higher than the max. speed indicated on the machine.
• Grinding wheels have to be stored and used carefully according to the instructions of the producer.
• Check the accessories before use. Do not use any products which are broken, cracked or damaged in another way.
• Before use, make sure that the tool is correctly fixed and fastened. Let it run idle for about 30 seconds in a safe position. If considerable vibrations occur or if other defects are recognised, switch off immediately.
• Always lead the mains and extension cable as well as the extraction hose to the back away from the machine.
• Power tools have to be inspected by a specialist in regular intervals.
• Never carry the machine at its cable.
• Do not touch rotating parts.
• Persons under 16 years of age are not allowed to use the tool.
• During use, the operator and other persons standing nearby have to wear suitable ear protectors, a dust mask and protection goggles.
• Make sure that persons in the work space are not endangered by particles flying around.
• Keep the handles dry, clean and free of oil and grease.
• During operation, always hold the tool with both hands.
• Attention! The tool still runs for a little while after the machine was switched off.

For further safety instructions, please refer to the enclosure!

Electrical Connection
Before starting the machine check the correspondence between voltage and frequency according to the data mentioned on the identification plate. Voltage differences from + 6 % and – 10 % are allowed. The grinder is made in protection class II. Only use extension cables with a sufficient cross- section. A cross-section that is too small could cause a considerable drop in performance and an overheating of machine and cable.

Recommended minimum cross-sections and maximum cable lengths

Switching on and off
The EBS 125.1 is equipped with a lock-off button against an unintentional switch-on.

• Switching-on: push the lock-off button forward (1) and then the on/off switch down (2)
• Switching-off: release the on/off switch

Application of Grinding Wheels

Type| Max.

Rated Speed

| Color| Application
---|---|---|---
Diamond Grinding Wheel
Concrete| 10,000 rpm| gold, sand| for finishing and facing concrete, brick, lime sand-stone, basalt, sandstone
Screed| 10,000 rpm| yellow| for finishing fresh and green concrete, screed, lime mortar plaster, mortar,

plaster, soft limestone

Rapid K| 10,000 rpm| blue| for removing epoxy resin and two- component coatings

Changing the Diamond Grinding Wheel

Attention! The grinding wheel might heat up enormously during operation. You could burn your hands or get cut or ripped by the segments. Therefore, always use protective gloves when changing the grinding wheel. Before any work on the tool, disconnect the plug from the mains

• Actuate the spindle stop and keep it pressed.
• Use the face spanner to unscrew the driving nut. Then remove the mounted grinding wheel respectively mount the new one. The assembly works the other way round! Pay attention that the collar of the clamping nut faces away from the machine, as shown in the figure.
• In order to check whether the spindle stop is released before you switch on the tool, turn the spindle slightly. Let the machine run for a short period of time and in a safe position. If the machine does not run easily, stop working immediately. Use only the original accessory

Dust Extraction
Dust that occurs during your work is hazardous to health. That is why the EBS 120.1 must be used with a vacuum cleaner, and a dust mask has to be worn. The suitable Wet/Dry Vacuum Cleaner (dust category M) is available as accessory. It can directly be attached to the connection on the dust hood.

Changing the brush rim
If the length of the brushes is – due to wear – smaller than 5 mm (extreme formation of dust during grinding), the brush rim has to be replaced completely. Pull out the worn brush rim and replace it by a new one.

Instruction for Use
Switch the machine on and put it carefully on the surface you want to work on. Hold the tool with both hands and work with circular or linear movements. For best working results: Don’t put too much pressure on the surface you want to work on.

For grinding works right into edges of the wall one segment of the dust guard can be opened by means of the chucking device. This allows grinding on surfaces which are usually hard to reach. In this case, an increased amount of dust is possible.

Attention! All other grinding works have to be done with the complete dust guard.

Care and Maintenance

Before the beginning of the maintenance- or repair works you have to disconnect the plug from the mains.

Repairs may be executed only by appropriately qualified and experienced personnel. After every repair the machine has to be inspected by an electric specialist. Due to its design, the power tool needs a minimum of care and maintenance. The following works have to be carried out or rather the component parts have to be inspected:

• Always keep the power tool and the ventilation slots
• During work, please pay attention that no particles get inside the
• In case of failure, a repair has to be carried out by an authorised service workshop.

Our after-sales service responds to your questions concerning maintenance and repair of your product as well as spare parts. EIBENSTOCK’s application service team will gladly answer questions concerning our products and their accessories.

Environmental Protection
Raw Material Recycling Instead of Waste Disposal To avoid damages on transportation, the power tool has to be delivered in a sturdy packing. Packaging as well as unit and accessories are made of recyclable materials and can be disposed accordingly. The tool’s plastic components are marked according to their material, which makes it possible to remove environmental friendly and differentiated because of available collection facilities.

Only for EU countries
Do not dispose of electric tools together with household waste material! In observance of the European Directive 2012/19/EU on waste electrical and electronic equipment and its implementation in accordance with national law, electric tools that have reached the end of their life must be collected separately and returned to an environmentally compatible recycling facility.

1. The indication of noise emission is measured according to DIN 45 635, part
2. The level of acoustic pressure on the work place could exceed 85 dB (A); in this case protection measures must be taken.

Wear ear protectors!
The typical hand-arm vibration is below 2.5 m/s2. Measured values determined according to EN 60 745.

The declared vibration emission level represents the main applications of the tool. However if the tool is used for different applications, with different accessories or poorly maintained, the vibration emission may differ. This may significantly increase the exposure level over the total working period An estimation of the level of exposure to vibration should also take into account the times when the tool is switched off or when it is running but not actually doing the job. This may significantly reduce the exposure level over the total working period. Identify additional safety measures to protect the operator from the effects of vibration such as: maintain the tool and the accessories, keep the hands warm, organisation of work patterns.

Dust protection

Dust from material such as paint containing lead, some wood species, minerals and metal may be harmful. Contact with or inhalation of the dust may cause allergic reactions and/or respiratory diseases to the operator or bystanders. Certain kinds of dust are classified as carcinogenic such as oak and beech dust especially in conjunction with additives for wood conditioning (chromate, wood preservative). Material containing asbestos must only be treated by specialists.

• Where the use of a dust extraction device is possible it shall be used.
• To achieve a high level of dust collection, use industrial vacuum cleaner (dust category M) for wood and/or minerals together with this tool.
• The work place must be well ventilated.
• The use of a dust mask of filter class P2 is recommended.

Warranty
According to our general terms of delivery for business dealings, suppliers have to provide to companies a warranty period of 12 months for redhibitory defects (to be documented by invoice or delivery note). Damages due to natural wear, overstressing or improper handling are excluded from this warranty. Damages due to material defects or production faults shall be eliminated free of charge by either repair or replacement. Complaints will be accepted only if the tool is returned in non-dismantled condition to the manufacturer or an authorized Eibenstock service centre.

Declaration of Conformity
We declare under our sole responsibility that the product described under “Technical Data” is in conformity with the following standards or standardization documents:

• EN 60745-1:2006
• EN 60745-2-22:2013-12
• EN 55014-1:2017/A11:2020
• EN 55014-2:2021-04-01
• EN 61000-3-2+A1:2019-03-05
• EN 61000-3-3:2020-07
• EN IEC 63000:2019-05 according to the provisions of the directives 2011/65/EU, 2014/30/EU, 2006/42/EG

Technical file (2006/42/EC) at: Elektrowerkzeuge GmbH Eibenstock

Lothar Lässig
General Manager
07.02.2023

Frank Markert
Head of Engineering

Declaration of Conformity
We declare as the manufacturer under our sole responsibility that the product described under “Technical Data” fulfi lls all the relevant provisions of the following Regulations S.I. 2008/1597 (as amended), S.I. 2017/1206 (as amended), S.I. 2012/3032 (as amended) and that the following designated standards have been used:

• BS EN 60745-1:2006
• BS EN 55014-1:2017/A11:2020
• BS EN 61000-3-2+A1:2019-03-05
• BS EN IEC 63000:2019-05
• BS EN 60745-2-22:2013-12
• BS EN 55014-2:2021-04-01
• BS EN 61000-3-3:2020-07

Technical file (S.I. 2008/1597) at: Elektrowerkzeuge GmbH Eibenstock

Lothar Lässig
General Manager
07.02.2023

Frank Markert
Head of Engineering

Subject to change without notice

References

• EIBENSTOCK Elektrowerkzeuge | Qualitätswerkzeuge

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>