PHILIPS DEIFANT NOA0039R Home Power Photocell Timer User Guide

: June 13, 2024
: Philips

Table of Contents

Product description
Installation instructions
FCCSTATEMENT
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

PHILIPS DEIFANT NOA0039R Home Power Photocell Timer

Product description

A. Outdoor timer Plug the device(s) to be controlled into the grounded outlet(s) on the bottom of the outdoor timer.
B. Wireless remote transmitter Press the ON button on the remote to turn on the lamp(s) or device(s) plugged into the timer. Press the OFF button to turn fixture(s) off.

See installation instructions.

Installation instructions

Mounting the timer
• Mount the timer (A) onto a wall near a GFCI outlet.
• Install a nail or screw (not included) into a wall.
The nail or screw must extend at least 7/8in. from the wall and allow the timer to be above ground level as far as possible.

• Hang the timer (A) from the eyelet on the top left of the unit with the receptacles (D) facing downward so moisture does not accumulate.
• Plug the grounded power cord (C) into a GFCI outlet.
• Plug the device you wish to control into either receptacle (D).
Preparing the remote:
• Pull the plastic tab on the remote to activate battery.
Plug in the timer and press the remote’s ON button. The timer should turn on.
Pairing remote and timer: Timer should be paired to the remote, but if it does not work:
• Press any button on the remote. The red indicator light on the timer stops flashing when pairing is successful.
Changing the battery (B):
• Remove the Phillips screw and slide the battery cover from the remote.
Plug in the timer, press the button three times quickly, and the red LED ashes.
• Remove the battery and insert a new CR2032 battery — note polarity.
• Replace the cover and screw.

FCCSTATEMENT

JascoProductsCo.,10E.MemorialRd., Oklahom Suppliers Declaration of Conformity |Model#:NOA0039R| aCity,OK 73114, www.byjasco.com
FCC Warning:

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help.
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator and your body.

RISK OF ELECTRIC SHOCK:

FULLY INSERT THE PLUG INTO A GFCI CONTROLLED RECEPTACLE
KEEP CHILDREN AWAY
DO NOT USE WITH EXTENSION CORDS
INSTALL TIMER AS FAR ABOVE GROUND LEVEL AS POSSIBLE WITH THE RECEPTACLE FACING DOWNWARD
NOT FOR WATER IMMERSION OR FOR USE WHERE DIRECTLY EXPOSED TO DRIPPING OR SPLASHING WATER
UNPLUG BEFORE CLEANING RISK OF FIRE:
DO NOT EXCEED ELECTRICAL RATINGS
DO NOT USE TO CONTROL APPLIANCES THAT CONTAIN HEATING ELEMENTS (COOKING APPLIANCES, HEATERS, IRONS, ETC) BATTERY WARNING:
BATTERIES MAY LEAK HARMFUL LIQUIDS OR IGNITABLE MATERIALS OR EXPLODE CAUSING INJURY OR PRODUCT DAMAGE
DO NOT MIX OLD AND NEW OR OTHER BATTERY TYPES
REPLACE ALL BATTERIES AT THE SAME TIME
REPLACE FULLY DISCHARGED BATTERIES IMMEDIATELY
REMOVE BATTERIES IF PRODUCT IS TO BE UNUSED FOR AN EXTENDED PERIOD OF TIME

RECEIVER

Functional Range ………………………………………………………………Up to 80 ft.
Maximum Tungsten Load ……………………………………………….1000 W, 8 A
Maximum Resistive Load ………………………………………………1875 W, 15 A
Rating ……………………………………………………………………………125 VAC/60 Hz

TRANSMITTER
Functional Range ………………………………………………………………Up to 80 ft.
Battery Type ………………………………………………..Use only CR2032 battery

Functional range may be affected by one or more of the following factors: weather, radio frequency interference, low transmitter battery, and obstructions between the transmitter and receiver.

MADE IN VIETNAM
Philips and the Philips Shield Emblem are registered trademarks of Koninklijke Philips N.V. and are used under license. This product has been manufactured by and is sold under the responsibility of Jasco Products Company, and Jasco Products Company LLC, 10 E. Memorial Rd., Oklahoma City, OK 73114 is the warrantor in relation to this product.
This product has a 1-year limited warranty.
Visit www.philips.com/support for warranty details. Questions? Contact our U.S.-based Consumer Care at 1-844-816-0320, M-F, 7AM-8PM Central Time. For product patent information, visit www.byjasco.com/patents.