hOMACER CM-YT1TGH240C Polished Black Interior J-strap Barn Door Hardware Kit Instruction Manual

June 13, 2024
HOMACER

hOMACER logo CM-YT1TGH240C Polished Black Interior
J-strap Barn Door Hardware Kit
Ceiling Mount Non-Bypass Single/Double Door
Instruction ManualhOMACER CM YT1TGH240C Polished Black Interior J strap
Barn Door Hardware Kit

SAFETY PRECAUTIONS

WARNING!

  • Power tools can cause serious damage if not professionally used. Safety gear must be worn before installation to prevent unexpected injuries.
  • Pick an area free of hazardous condition before you start on the project. Please use tools and power tools responsibly,any loss of control and accident deaths may occur due to abuse of tools.
  • Please make sure all hardware secured on to the door is sufficiently tight. Doors with loose hardware may result in unexpected serious injuries. To avoid any problems, be sure hardware is secure before door is put on the track.
  • All hardware provided is for safety reasons. Anti-Jump systems are to prevent doors from falling off the track while in use. Please follow each instruction carefully. Track must be installed on studs in order to keep the track and doors secure from serious problems. All safety hardware and instructions included in this project must be used and followed specifically to prevent any unforeseen serious problems.

!CAUTION!

  • Big objects required in this project are needed to be carefully and responsibily moved. Be sure to wear safety gloves and shoes to prevent any serious injury.
  • Be extremely careful to not put any parts of your body against a moving part of the hardware. This may cause bruising, punctures, and other results of injuries when for example when fingers are caught in the closing area of the doors.
  • Precautions should be taken when opening or closing the door(s). Handles should be used when attempting to slide the door(s). Always keep you and children aware and safe from any unexpected situations.
  • Any extreme uncontrolled pressure opening or closing the door(s) can damage the hardware gradually. Use handle(s) to open and close the door(s) with care at all times.

HARDWARE INCLUD

Different track length comes with different hardware quantity.
Please be sure to check the hardware you should have before installation.
Hanger/Roller SethOMACER CM YT1TGH240C Polished Black Interior J strap
Barn Door Hardware Kit - Hanger Roller Set Junction Plate
Please check the Hardware Checklist below, for this item you may not need any.

Ceiling Mount Bracket SethOMACER CM YT1TGH240C Polished Black Interior
J strap Barn Door Hardware Kit - mount bracket Set

Flat Track

HARDWARE CHECKLIST

Track Measurement| Hanger/Roller Set for Single Door Kit| Hanger/Roller Set for Double Door Kit| Flat Track| Ceiling Mount Bracket Set| Junction Plate
---|---|---|---|---|---
4FT| 1| 2| 1| 3| 0
4.5FT| 1| 2| 1| 3| 0
5FT| 1| 2| 1| 4| 0
5.5FT| 1| 2| 1| 4| 0
6FT| 1| 2| 1| 5| 0
6.6FT| 1| 2| 1| 5| 0
7FT| 1| 2| 1| 5| 0
7.5FT| 1| 2| 1| 6| 0
8FT| 1| 2| 1| 6| 0
9FT| 1| 2| 2| 6| 1
10FT| 1| 2| 2| 8| 1
11FT| 1| 2| 2| 8| 1
12FT| 1| 2| 2| 10| 1
13FT| 1| 2| 2| 10| 1
14FT| 1| 2| 2| 10| 1
15FT| 1| 2| 2| 12| 1
16FT| 1| 2| 2| 12| 1
18FT| 1| 2| 3| 15| 2
20FT| 1| 2| 3| 15| 2

TYPE OF HANGERS Please follow the measurement stated below, measuring from the top of the door to the center of the first hole.

PRE – INSTALL NOTICE

DOOR THICKNESS
Make sure the door you use is within the thickness of 1-3/8” ~ 1-3/4”. Consider getting different size hex bolts for the rollers when it falls out of the door thickness range since the one provided in the box may only fit the range above. You can search “hex bolt” on our website and select the size and color according to the size chart in the description of the hex bolt.

HEADER BOARD
Header is suggested when the studs do not line up with the track.
DRILL BIT SIZEShOMACER CM YT1TGH240C Polished Black Interior J strap
Barn Door Hardware Kit - Drill bit Sizes DOOR WEIGHT
This hardware total weight capacity is 220lbs. If all the studs are attached to the track and installed properly the weight capacity may go up to 300lbs maximum in total for all doors combined.
WHAT HEIGHT DOOR DO I NEED?
Height of Room – 6 1/4” – (Header Board Thickness) = Door Height

INSTRUCTIONS

![hOMACER CM YT1TGH240C Polished Black Interior J strap Barn Door Hardware Kit

  • Door thickness](https://manuals.plus/wp-content/uploads/2023/09/hOMACER-CM- YT1TGH240C-Polished-Black-Interior-J-strap-Barn-Door-Hardware-Kit-Door- thickness.jpg)First measure the thickness of the door being used.
    If it is 1 5/8” or less you can mount the bracket against the wall while mounting on the ceiling studs.
    If your door thickness is thicker than 1 5/8” the bracket has to be mounted further from the wall on the ceiling.
    Example: If your door thickness is 2 1/2”. Take 2 1/2” minus the max door thickness (1 5/8”). You will get 7/8”. Rounding that off you can mount the brackets away from the wall on the ceiling about 1”.
    REMINDER: If your door is thicker than 1 3/4” or thinner than 1 1/4” you will have to visit our website to purchase the longer or shorter bolts than the one provided in the box. Which fits the door thickness range of 1 1/4” to 1 3/4”.hOMACER CM YT1TGH240C Polished Black Interior J strap Barn Door
Hardware Kit - ceiling studsMake sure you have ceiling studs for this setup!
    Use a leveler to make sure your ceiling is levelled.
    Draw 2 lines on the ceiling parallel to the wall.
    Line 1 is 1 3/16” away from the wall and Line 1 is 1 3/8” away from line 2 that is If you are putting the bracket against the wall.
    If you are putting the bracket further away from the wall because of the door thickness. Make sure you add the measurement to how much you are putting the bracket away from the wall to the measurements on line 1 and 2.
    REMINDER: If the studs do not line up please use a header board of 1in at least. Keep in mind this also minimizes the height of the door needed for this setup. Check page 3 for pre-install notice.hOMACER CM YT1TGH240C Polished
Black Interior J strap Barn Door Hardware Kit - Assemble
junctionIf your track comes in 2pcs or more, install the junction plate on to each two tracks like the diagram shown here.
    Assemble junction plate first if included with your kit.
    Put the track against the ceiling (you will need an extra hand for this) and mark up the holes on the previous line drawn. Then drill pilot holes using 3/16” drill bit.
    Make sure the track spands in the middle of the opening and where the door sits when opened. hOMACER CM YT1TGH240C Polished Black Interior J strap Barn
Door Hardware Kit - BracketsInstall all the Brackets like the diagram shown on to the predrilled holes with the Lag Bolts provided. hOMACER CM YT1TGH240C Polished
Black Interior J strap Barn Door Hardware Kit - connector
providedInstall the track on to the brackets with the track connector provided.hOMACER CM YT1TGH240C Polished Black Interior J strap Barn Door
Hardware Kit - Turn clockwiseInstall the door stoppers on each end of the track.
    Like the diagram with hex wrench.
    This door stopper is adjustable. You can change up the position however you like by just sliding it on the track and tightening it where you need it to be. It slides over all lag bolt head making it easy to install.hOMACER CM
YT1TGH240C Polished Black Interior J strap Barn Door Hardware Kit - floor
guidesRoute a slot that is 1/4” wide and 13/16” deep at the bottom of the door for all three doors. If you do not want to open a slot underneath your doors, we provided a 2-in-1 floor guide which will show 2 mounting ways on step 11. If you would like to purchase special floor guides not provided you can look up “floor guides” at the top left search bar of our website to see all the types of floor guides we sell.hOMACER CM YT1TGH240C Polished Black Interior J
strap Barn Door Hardware Kit - hanger accordingInstall the anti-jump pads on top of the door as shown on the picture, it is suggested to mount them right below the track. Two is provided for each door. One on each end.
    Drill the holes for the hanger according to the dimension given in the picture. The distance between the top edge of the door and the center of the upper hole is 1 5/8”. The distance between the side edge of the door and the hanger is up to your choice. Typically around 1” to 2”. Next, install the hex bolts and acorn nuts as shown in the picture.
    Please follow the diagram above on how the hex bolt, washers and nut should be installed on the door and hangers. Do not install them any other way since it may interfere with the function of the sliding system.hOMACER CM YT1TGH240C
Polished Black Interior J strap Barn Door Hardware Kit - doors on to the
trackTo mount your doors on to the track, you will have to lift your door at a slight angle and rest both wheel grooves onto the top of the track carefully.

STEP 11
For the floor guides of ceiling mount hardwares we recommend to install the floor guide on the edge of the opening where the door sits or slides over to. Here below is a diagram of the 2 ways you can use the given floor guide.hOMACER CM YT1TGH240C Polished Black Interior J strap Barn Door
Hardware Kit - Groove DoorIf you are looking for different floor guides please check out our website. Type in “Floor Guide” in the search bar of our website and you will be able to find a few types. hOMACER CM YT1TGH240C Polished Black
Interior J strap Barn Door Hardware Kit - floor guideOur preferred location of the floor guide

YOUR INSTALLATION IS COMPLETE!
www.homacer.com

SLIDING HARDWARE / BARN DOORS
High Quality Exquisite Design Outstanding Services
ABOUT US
At Homacer, our goal is to provide the finest sliding barn door hardware products and services for our valued customers. We keep polishing our products to make their quality better, prices lower and installation easier. We make it possible for you to get everything you need from us when you think about installing sliding barn doors.

CONTACT US
Bulk Membership Program
To learn more about bulk / dropship order program you may contact us at Office

: 1(770)-559-5849

Website: www.homacer.com/pages/membership- program
Email us: sales@homacer.com

CUSTOMER SERVICE TECH SUPPORT
Office #: 1(770) 864-5437
Website: www.homacer.com
Email us: info@homacer.com
LOCATION
1885 Beaver Ridge Cir, Ste A
Norcross, GA 30071
For additional hardware and accessories such as floor guide, soft close, and door handles, they can all be found on our website at www.homacer.com if you have any other inquiries you can always contact us through the phone or emails.

hOMACER logo

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals