Rasonic RSS-TS08 Mini Electric Stewing Mug Instruction Manual

RSS-TS08 Mini Electric Stewing Mug
Instruction Manual

RSS-TS08
Mini Electric Stewing Mug
OPERATION MANUAL

RSS-TS08 Mini Electric Stewing Mug

• Please read the operation manual carefully before using. Keep it in a safe place for future reference.
• Some figures in this manual may not match with the real object, just for reference only.

Thank you for choosing Arsenic Mini Electric Stewing Mug. Read the operation manual carefully before using and keep this operation manual for your future reference.

Safety Precautions

When using the appliance, make sure to follow the below safety precautions:
1.1 Before in use

1. Read the following safety precautions before using the appliance. Failure or negligence in following these safety precautions could cause fire, electrical shock or injury.
2. Remove and discard all packing materials of the appliance. Make sure children do not play with them to avoid any danger.
3. Before connecting to the electricity, check if the rated voltage on the appliance corresponds to the local voltage. To avoid overload, do not connect the appliance in the same power socket with other high power consumption  appliances. Make sure the appliance is connected to power socket with grounding.
4. To avoid any hazard, make sure the surface of the appliance and plug is dry before use.

1.2 In operation

1. Never leave the appliance unattended when in use or operate without water.

2. Do not cook inside the water tank (heating plate) directly.

3. Do not operate the appliance in the following places:
   • Humid environment or near water sources
   • Near heat and fire sources (such as electric oven and induction cooker etc.)
   • Unstable and insufficient support surface
   • Near inflammable or non-resistant to heat objects (e.g. carpet, plastic table cloth, curtain and towel etc.)

4. Sufficient room must be reserved for steam or air bubbles generated, and amount of water should not exceed the maximum water level  of the water tank. Otherwise, water and steam may spill out during operation and  cause dangers.

5. Water may splash out from the edge of lid during operation. To avoid fire, electrical shock or injury, do not operate the appliance near the other appliances, electric socket extension and avoid spillage on the connector.

6. Make sure the lid is closed tightly to prevent water from splashing out or steam discharging; otherwise, the appliance may not function properly or cause hazards.

7. WARNING! Do not open the lid during operation or right after use, as massive steam will come out from the steam vent, only by doing so can prevent steam burn.

8. Do not open the lid during operation, otherwise boiled water may spill out and cause burns. If necessary, press 【Keep Warm/Cancel】 button to switch off the appliance before open the lid. Be careful of the hot steam and droplets when opening the lid.

9. After cooking, a lot of vapor and water droplets will remain inside the main body and lid, which is a normal phenomenon. To avoid burns, switch off the appliance and unplug the power, wait for a while before opening the lid to  avoid burn by residue heat. Open the lid carefully to avoid condensed water droplets from the lid drop onto the control panel or power cord. To avoid scalding by hot steam, use oven mitts to pick up the food from the appliance.

10.  Always use kitchen utensils with long handles when checking the food inside. Beware of hot steam, do not operate the appliance next to wall or furniture.

11. Do not switch on the appliance when there is no water in the water tank. If boil dry occurred, add water into the water tank or unplug the power.

12. Do not open the lid, move or shake the appliance during operation as to avoid massive steam emission resulting in burns or other hazards.

13.  To avoid appliance malfunction, deformation or discoloration, do not cover the appliance or steam vent by any object when using the appliance.

1.3 After use

1. Normally cleaned after use, unplug the appliance from the socket and let the appliance cool down before moving and cleaning.
2. To avoid getting burned, never touch the appliance enclosure and heating plate which are subject to residual heat right after use.
3. To avoid affecting the safety performance and prevent electric shock and fire, never immerse the main body, power cord or plug in water or let them wet. Make sure the plug is dry before use.
4. Disconnect the power plug after use or, when the appliance not in use for long time, preventing electric leakage and electric shock due to insulation degeneration. Do not touch, plug or unplug the appliance by wet hands which can result in electric shock.

1.4 Safety Precautions

1. The appliance equipped with boil-dry protection system. If water inside the water tank completely evaporated or temperature exceeds the protection level, the operation will stop while error code will show on display. If the appliance was boiled dry once, switch off the appliance, unplug the appliance from the socket, and cool down completely before reuse. WARNING! Boil-dry protection is the device for protection. Do not rely on the function to switch off the appliance.
2. Before cleaning, unplug the appliance and let it cool down completely.
3. The appliance is not intended to be operated by means of an external timer or separated remote control system, as to prevent short-circuit or other flammable hazards.
4. Do not let the ceramic mug withstand big temperature difference. (For example: Heat the ceramic mug with fire or put the hot ceramic mug on a marble surface or into cold water), otherwise the mug may crack because of thermal expansion and contraction.
5. To prevent corrosion on water tank and ceramic mug, avoid cooking any substance that is acidic or alkaline.
6. The ceramic mug is a kind of fragile ware. Use it carefully. Do not hit the mug or drop it from a high place to avoid damage.
7. Great care is necessary in using the appliance, especially near children. Children should be supervised to ensure that they do not play with the appliance. Also, children without adult supervision should not operate, clean and maintain the appliance. Keep them away from the appliance and its power cord.
8. Handle the power cord with care. Do not place heavy objects on the power cord. Never clip, modify, stretch or twist the power cord. Do not grasp the power cord but the plug itself when plug in or unplug the appliance. Ensure that the power plug fits all the way into the appliance socket, fail to do it may cause electric hazard.
9. Do not operate the appliance when the power cord is tangle or hang over the edge of a table, countertop or let it touch any hot surface. It may cause power cord damage.
10. Always wipe off any dust from the power plug and clean the appliance, make sure it is not oily, especially on the pins such to prevent fire from happening.
11. Do not use the appliance for purposes other than cooking. (If the appliance is not used for cooking, it may cause malfunction and hazard.)
12. Keep it out of reach for infants. Great care is necessary in using the appliance, especially near children. Make sure that they do not play with the appliance. Also, children without adult supervision should not operate the appliance do maintenance and keep them away from the appliance and its cord.
13. The appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, if they have given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved.
14. The appliance is intended to be used in household or similar applications such as staff kitchen areas in shops, offices and other working environments. Do not use it outdoors.
15. Always check the condition of the appliance, ceramic mug, power cord and plug. To avoid hazard, stop using the appliance immediately if the appliance is damaged or dropped. Contact Shun Hing Electric Service Centre Limited for checking and repairing.
16. Do not use, replace or assembly any parts which is not produced under authorization, otherwise, the warranty becomes invalid and our company will refuse any liability and repairing cost for the damage caused.
17. To comply with safety regulations and avoid hazards, if repair is needed, present the official invoice, product warranty card with the appliance for repair service and contact Shun Hing Electric Service Centre Limited hotline at 2406 5666. Address can be found at the back page of the manual.

Cleaning and Storage Method

1. Ceramic mug is a kind of fragile ware, handle with care and do not place in high temperature environment for a long time.

2. Use warm water together with mild detergent to clean the ceramic mug. Never use poisonous or corrosive detergent for cleaning.

3. To avoid malfunction and dangers, do not clean the main body with water directly or let water penetrate inside the main body.

4. To remove the odor, add some water to the ceramic mug and the water tank, turn on the appliance until water boiled. Pour out the water and wait until the appliance cool down completely. Then wash it with warm water.

5. Due to the minerals in water, colored water scale will be found on the heating plate after using the appliance. The harder the water, the quicker the scale will be formed. It is a normal phenomenon and will not affect the operation.

6. To remove the water scale, follow the below instructions:
   • Fill water into the water tank (fill water to the maximum water level is recommended)
   • Put halved sliced lemon in the water tank (or follow the ratio to add 2g citric acid per 100ml water).
   • Operate “Optional” function until the water boiled. Press the 【Function/Cancel】 key to stop the operation, wait and pour out all water after around 20 minutes. Then clean the heating plate with a sponge or soft brush, and rinse  by water at the end.
   NOTICE! To remove the remaining smell of citric acid, boil water again and pour it out afterward.

7. Never clean the appliance by using gasoline, cleanser or harsh cleaning tools (e.g. metal brush).

8. If dirt is attached on the water tank, main body or lid, use a damp cloth to clean and wipe them dry.

9. Always let the appliance cool down completely before storage. Put it in a paper box and store in a dry environment. Never wrap the power cord tightly around the appliance or put pressure on it to avoid the power cord damage.

Product Specifications

Control Panel and Product Structure

4.1 Control panel

4.2 Product Structure

4.3 Water Level Marks

Remarks: The above illustrations are for reference only and subject to the actual appliance.

Operation Instructions

5.1 Operation Time Table

✓ Support
✗ Not support

Function| Shown
on
Display| Default
Cooking
Time| Adjustable
Cooking Time
Range| Time
Adjustment
Per Press| Preset
Function| Preset
Time
Range| Keep
Warm
Function
---|---|---|---|---|---|---|---
Baby Congee| 2.| 1.5 hrs| 0.0 – 5.0 hrs| 0.1
(6 mins)| ✓| 0.0-12
hrs| ✓
Stewing Soup| 3.| 2.5 hrs| 0.0 – 5.0 hrs| ✓| ✓
Bird’s Nest| 1.0| 1 hr.| 0.0 – 1.5 hrs| ✓| ✓
Steam| 0.4| 24 mins| 0.0 – 0.6 hrs| ✓| X
Optional| 0.8| 48 mins| 0.0 – 1.5 hrs| ✓| ✓
Keep Warm| .| N/A
Preset| 2.0| 2 hrs| N/A| 0.5
(30 mins)| ✓| 0.0-12
hrs| X

• In the operating time of the above functions, every 0.1 unit of the displayed time value represents 6 minutes.
  5.2 First Use

  1. When the first time of use, it may have smell due to the new packing. It is a normal phenomenon where the smell will gradually disappear with time.
  2. Make sure the appliance is not plugged. Depend on the cooking functions, follow the instruction stated in “Chapter 5.3 Preparation” and “Chapter 5.4 Operation Instructions” to operate the appliance.

5.3 Preparation
CAUTION! Clean the ceramic mug thoroughly by water before using.
CAUTION! Do not exceed the maximum water level  of the water tank when filling water.
CAUTION! Use distilled water or tap water, never use mineral water as it will fasten the formation of scale.
CAUTION! When adding ingredients and water, it is recommended not to exceed 80% of the ceramic mug capacity to prevent water may spill out during operation.
When stewing: User can select “Baby Congee”, “Stewing soup”, “Bird’s nest” or “Optional” functions

1. Add water to the maximum water level “放盅前水位” of the water tank.
2. Put appropriate amount of ingredients and water into the ceramic mug supplied, and close the ceramic lid.
3. Place the ceramic mug into the main body, and close the lid finally.

• The appliance will change to keep warm mode automatically after the operation completed.

When steaming eggs: User can select “Steam” function

1. Add water to the water level of steam  of the water tank.
2. Put the eggs in the steaming tray, then place it into the main body
3. Close the lid finally.

• The appliance will return to the standby mode after the operation completed.

CAUTION! To avoid the power plug from getting wet by the water droplets, lift the lid vertically when open. To avoid water droplets dripping off onto the power cord and control panel, upside down the lid when lifting and let water droplets backflow to the lid.

5.4 Operation Instructions

1. After connecting to the power, the display will show “0.0” representing the appliance is in standby mode.
2. In standby mode, press 【Function/Cancel】 key to select desired function where Baby congee  > Stewing soup  > Bird’s nest > Steam  > Optional > Keep Warm  > “0.0” (Standby mode) will show in order. The corresponding  function indicator and default cooking time will flash at the same time.
3. After selecting function, it will be automatically confirmed after the function indicator and display time flash 6 times. The function indicator becomes solid, and the display will show the cooking time and “.” keeps flashing. When the preset temperature is reached during the preheating process, the operation time will start to count down.
4. To increase the cooking time, press the [+] key to adjust the time while the time is flashing (within about 6 seconds), or press and hold [+] key, the time can be fast forwarded. Time value will be increased by 0.1 unit per each press  until the maximum time value reached, and then return to “0.0” (Standby mode). More details in “Chapter 5.1 Operation Time Table”. After the setting completed, wait for the function indicator and the cooking time to flash 6 times  to confirm and the appliance starts to operate.
5.  To decrease the cooking time, press the [-] key to adjust the time while the time is flashing (within about 6 seconds), or press and hold [-] key, the time can be reversed. Time value will be decreased by 0.1 unit per each press until  the minimum time value reached, and then return to “0.0” (Standby mode). More details in “Chapter 5.1 Operation Time Table”. After the setting completed, wait for the function indicator and the cooking time to flash 6 times to confirm and the appliance starts to operate.
6. When the operation completed, “－.－” will show on display, “.” keeps flashing and keep warm indicator will light up (Except for “Keep Warm” and “Steam” functions). The appliance will switch to keep warm mode automatically.
7. If the keep warm function is not needed, press the【Function/Cancel】key to cancel during warm keeping. “0.0” will show on display and the appliance will return to the standby mode.
8. During the operation, the user can press【Function/Cancel】key to cancel the operation at any time, and the appliance will return to the standby mode or user can press [+] or [-] key to adjust the cooking time freely during operation.

CAUTION! Suggested to wait for about 5 minutes before opening the lid and taking out the food, as it can avoid burns by water spilling.
CAUTION! If user adjusts the cooking time (more than the default cooking time of the appliance), ensure that there is enough water in the water tank allow if the appliance to operate continuously.
CAUTION! The appliance will automatically stop operation if water inside the water tank evaporated during operation or warm keeping. The error code “E3” will show on display at the time when the operation suspended. User must wait for the appliance to fully cool down until the temperature drops below protection value, and reconnect the power supply before reusing the appliance.
5.5 Preset function (The time to finish the operation)
Follow the procedures described in “Charter 5.3 Preparation”, place the ingredients and clean water into the ceramic mug, and follow the steps below to preset the time.
CAUTION! Perishable foods are not recommended for long preset time as to avoid deterioration.

1. In standby mode, press the【Preset】key, the preset indicator will light up and the preset time “2.0” will flash on the display. User can press the [+] or [–] key again to adjust the preset time during the flashing of the preset time. If it flashes 6 times continuously without any operation, the appliance will return to standby mode.

2. After preset time is set, press【Function/Cancel】key to select function. If need to adjust the time, press the [+] or [–] button to adjust the function cooking time during the time flashing, or wait for the function indicator and the  cooking time to flash 6 times for automatic confirmation.

3. After setting is completed, the preset and corresponding function indicator will become solid, representing that preset function setting is completed. The display will show the preset time and “.” keeps flashing.
   CAUTION! After completing the preset function setting, the function and time cannot be adjusted.

4. To cancel the preset function, press the【Function/Cancel】key, the display will display “0.0”, and the appliance will return to standby mode.

Example of preset function setting:

Preset 5 hour to finish the “Stewing  function for 3 hours.

1. After connecting to the power, “0:0” will show on the display representing that the appliance is in standby mode.
2. Press the【Preset】key once, the preset indicator will light up and the default preset time “2:0” (2 hours) will show on display. Press the【+】key to adjust the time setting to “5.0” (5 hours).
3. Press the【Function/Cancel】key to select the “Stewing Soup” function, corresponding indicator and default cooking time “2.5” (2 hours 30 minutes) will flash at the same time. . Press the【+】key to adjust the cooking time to “3.0” (3 hours).
4. After setting is completed, wait for the function indicator and the cooking time to flash 6 times to confirm the setting. The display shows “5.0” and ” . ” flashing, and “Preset” and “Stewing soup ” indicators will light on at the same time, indicating that the “Preset” function is completed, and the appliance starts to count down.
5. After around 2 hours, preset indicator will light off, “Stewing soup ” function will start until the operation completed. “－.－” will show on display, ” . ” keeps flashing and keep warm indicator will light up. The appliance switches to  keep warm mode automatically.

CAUTION! Warm keeping will continue until water inside the water tank is evaporated. (Detailed information can be found in “Chapter 5.6 Keep Warm Function”.)
CAUTION! The preset time is the overall cooking completion time.
CAUTION! If the selected cooking time is longer than preset time, operation will start immediately.

5.6 Keep Warm Function

The appliance will change to keep warm mode automatically after the operation completed (Except for “Steam” function).

No defined operation time for warm keeping, it will stop until the water inside the water tank is evaporated.

User can press the【Function/Cancel】key to select “Keep Warm” function, related indicator and “－.－” will flash at the same time. Wait for the function indicator and “－.－” to flash 6 times to confirm the setting, “－－” lights up on the  display and ” . ” keeps flashing.

To cancel “Keep Warm” function during operation, press the【Function/Cancel】key once, “0.0” will be shown on display and the appliance will return to standby mode. User can unplug the appliance from the socket after the appliance  cool down.
CAUTION! Do not warm perishable foods for too long, otherwise, it may generate odor and get deteriorated.
CAUTION! When the water tank is out of water, error code “E3” will be shown on display, the appliance will turn off automatically. User must wait for the appliance to fully cool down until the temperature drops below protection value,  and then reconnect the power supply before reusing to use the appliance.
5.7 Cancel Function
During operation, if cancellation of the cooking or preset function is needed, press the 【Function/Cancel】key once. “0.0” will show on display, representing the appliance will return to standby mode.

 Troubleshooting and Treatment

If the following situation happens, unplug the appliance immediately. Contact and report to Shun Hing Electric Service Centre Limited for checking and repairing.

1. If the power cord or power plug is abnormally hot.
2. If the electricity flows discontinuously when the power cord is bent.
3. If the appliance is abnormal hot, and burnt smells or smoke.
4. If you get shocked when touching the appliance.
5. If the appliance sometimes does not turn off automatically.
6.  If water is leaking out from the appliance.

carefully. If the problem cannot be fixed, contact Shun Hing Electric Service Centre Ltd. for checking and repairing.
Error Code “E3”| Is there enough water in i the water tank?| Unplug the power supply, wait for the appliance to fully cool down, add an appropriate water, and then reconnect the power supply before using the appliance.

If the above remedies/solutions cannot fix the problem, switch off the appliance immediately, contact Shun Hing Electric Service Centre Ltd. (Tel: 2406 5666) for inspection and repairing. To avoid any danger and damage to the appliance, do not disassemble or repair it by yourself.

Special Avowal

1. The information above has been checked; our company reserves the hermeneutic power to any print errors or misunderstanding on the content.
2. Please note that any technology improvement will be added to the new versions of operation manual without any prior notices. The product appearance and color are subject to the actual appliance.
3. In case there is any inconsistency or conflict between the English versions and Chinese versions of the terms, the Chinese versions shall prevail.
4. E-copy of operation manual can be sent by e-mail on request, please call Shun Hing Electric Works and Engineering Co., Ltd at 2861 2767.

After Sales Service

1. For any defect, in the judgement of technician from Shun Hing Electric Service Centre Limited, caused under normal use, our company is responsible for repairing or replacing parts of the said electrical appliance free of charge  within one year guarantee period commencing from the date of purchase. Any defect part which has been replaced shall become our property. Guarantee service does not cover the repair or replacement of consumable parts etc.
2. User must present the official invoice/redemption voucher and the product warranty card with the chop from sales point/redemption center for maintenance. For enquiries, please call Shun Hing Electric Service Centre Limited hotline at 2406 5666.
   SHUN HING ELECTRIC WORKS AND ENGINEERING CO., LTD.

Office: 9/F, Peninsula Centre, 67 Moody Road, Tsimshatsui East, Kowloon, Hong Kong
Tel: 2861 2767
Fax: 2865 6706
Website: http://www.rasonic.com
E-mail: shew@shunhinggroup.com
11/F, Shun Hing Centre, 2 Sheng You Street, Kwak Chung, N.T. HK
Tel: 2406 5666
Fax: 2408 0316
Website: http://www.shesc.com/zh
Customer Service Centre
1/F, Shun Hing Centre, 2 Sheng You Street, Kwak Chung, N.T.
9/F., Block B, Peninsula Centre, 67 Moody Road, Tsum Sha Tsoi East, Kowloon
22/F, Parkview Centre, 7 Lau Li Street, Tin Hua, Hong Kong
Avenida de Wenceslaus de Morays, No. 193-199, 5 Andar – I, Def.. Industrial Nam Lang, Macau
For the latest information of Hong Kong and Macau service center, please visit: http://www.shesc.com/en

References

• 信興電工工程有限公司
• 信興電工工程有限公司
• Shun Hing Electric Service Centre Ltd
• Shun Hing Electric Service Centre Ltd

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>