JASCO ZWN4108 Plug In Smart Switch User Guide

76724
ZWN4108 Z-Wave’ certified wireless lighting control

Thank you for your purchase!

Instructions made easy
Read instructions or watch easy-to­ follow video.
Scan code or visit

byjasco.com/76724i

Register your product
Receive exclusive deals and register your product.
can code or visit

byjasco.com/deals

For additional Jasco Pro Series products, visit our website www.jascopro.com.

Like our product?
Leave a review on your favorite retailer website or amazon.com
Having problems?
Let us know how we can help Cal I1-800-654-8483 between 7AM-8PM, M-F, Central Time

ADDING YOUR DEVICE TO AZ-WAVE NETWORK

1. Follow the instructions for your Z-Wave certified controller to add a device to the Z-Wave network.
2. Once the controller is ready to add your device, press the program button of the smart switch.

You have complete control to turn your lamp ON/OFF according to groups, scenes, schedules and interactive automations programmed by your controller.
If your Z-Wave certified controller features remote access, you can control your lamp from your mobile devices.
If prompted by the controller to enter the S2 security code, refer to the QR code/security number on the side of the box or the QR code label on the product (see Figure 1). Enter the 5-digit code.
Figure 1:
TO REMOVE AND RESET THE DEVICE

1. Follow the instructions for your Z-Wave certified controller to remove a device from the Z-Wave network.
2. Once the controller is ready to remove your device, press the program button of the smart switch.

TO RETURN YOUR SWITCH TO FACTORY DEFAULTS

1. If plugged in, unplug the switch from the receptacle.
2. Press and hold the program button for at least three seconds while you plug the switch into a receptacle.

NOTE: This should only be used if your network’s primary controller is missing or otherwise inoperable.
NOTE: Smart Start enabled products can be added into a Z-Wave network by scanning the QR code on the product with a controller providing Smart Start inclusion. No further action is required and the Smart Start product will be added
automatically within 70 minutes of being switched on in the network vicinity.

SPECIFICATIONS – IMPORTANT!

ZWN4108
Power VAC, 60Hz
Signal (frequency)
Maximum load
600W (5A) tungsten, 1/2HP motor or 1800W (15A) resistive
Wireless range (Classie): Up to 150ft.
line of sight between the wireless controller and the closest Z-Wave receiver module
Wireless range (Long Range): Up to 1300ft.
line of sight to the wireless controller
Operating temperature range 32-104°F (0-40° C)
For indoor use only
Specifications subject to change without notice due to continuing product improvement
NOT FOR USE WITH MEDICAL OR LIFE-SUPPORT EQUIPMENT Z-WAVE ENABLED DEVICES SHOULD NEVER BE USED TO SUPPLY POWER TO OR CONTROL THE ON/OFF STATUS OF MEDICAL OR LIFE-SUPPORT EQUIPMENT.
NOT FOR USE WITH MEDICAL OR LIFE-SUPPORT EQUIPMENT
Z-WAVE ENABLED DEVICES SHOULD NEVER BE USED TO SUPPLY POWER TO OR CONTROL THE ON/OFF STATUS OF MEDICAL OR LIFE-SUPPORT EQUIPMENT.

FEATURES

Must not exceed 600W (SA) incandescent, 1800W (15A) resistive or 1/2HP motor

• Two Z-Wave controlled AC outlets for LED, CFL, incandescent and halogen lights as well as small appliances
• Remote ON/OFF operation via the Z-Wave controller
• Manual ON/OFF control with the front-mounted push button
• Space-efficient design
• Grounded three-wire power connection for safety
• This Z-Wave device has advanced features that allow you to customize your experience. These features can only be adjusted by a Z-Wave enabled controller that supports the Z-Wave configuration command class. For a complete list of adjustable configurations, visit www.ezzwave.com/config
• Supports Z-Wave Long Range – requires Z-Wave hub that supports Z-Wave Long Range
• Can be added as a Z-Wave Long Range or standard Z-Wave device

A. Manual/program button
Single press turn ON/OFF the device
Single press – include or exclude in Z-Wave network
B. LED indicator
C. Z-Wave controlled outlets – both outlets are controlled together and can remotely turn ON/OFF the connected device(s)
CYCLE LED
The LED behind the program button acts as a guide light or status indicator.
How to cycle through options:
Press program button 10 times quickly.

1. LED is ON when the load is ON (indicates the outlet is ON) (default)
2. LED is always OFF
3. LED is always ON
4. LED is ON when the load is OFF (guide light in the dark)

PLUGGING IN YOUR Z-WAVE DEVICE

Plug in the smart switch to an indoor grounded outlet.
NOTE: Plug directly into outlet. Do not use with extension cords.

Plug the device to be controlled into the Z-Wave controlled outlet. Be sure the power switch on the controlled device is in the ON position.

The manual/program button on the smart switch allows the user to:

1. Manually turn ON/OFF the connected device.
2. Add/remove the smart switch from the network.

Z-WAVE INTEROPERABILITY
This product can be included and operated in any Z-Wave network with other Z-Wave certified devices from other manufacturers and/or other applications. All non-battery operated nodes within the network will act as repeaters regardless of vendor to increase reliability of the network
This device supports association command class (3 Groups)
Association Group l supports Lifeline, Binary Switch Report
Association Group 2 supports Basic Set and is controlled by pressing the ON or OFF button with the local load
• Association Group 3 supports Basic Set and is controlled by double pressing the ON or OFF button
• Each Association Group supports 5 total nodes
For product patent information, visit www.byjasco.com/patents
All brand names shown are trademarks of their respective owners
MADE IN VIETNAM
Distributed by Jasco Products Company LLC, IO E. Memorial Rd., Oklahoma City, OK 73114
This Jasco product has a 5-year limited warranty. Visit www.byjascocom for warranty details
Questions? Contact our U.S.-based Consumer Care at 1-800-654-8483, M-F, 7AM-8PM Central Time
©JASCO 2023 I ZWN4108 I 76724 I 06/26/23 vl
IC Caution.
This device complies with Industry Canada license-exempt RSS standard(s).
Operation is subject to the following two conditions: (1) This device may not cause interference, and (2)
This device must accept any interference, including interference that may cause undesired operation of the device.

WARRANTY

Jasco Products Company warrants this product to be free from manufacturing defects for five years from the original date of consumer purchase. This warranty is limited to the repair or replacement of this product only and does not extend to consequential or incidental damage to other products that may be used with this product. This warranty is in lieu of all other warranties, expressed or implied. Some states do not allow limitations on how long an implied warranty lasts or permit the exclusion or limitation of incidental or consequential damage, so the above limitations may not apply to you. This warranty gives you specific rights and you may also have other rights which vary from state to
state. Please contact our US.-based Consumer Care at 1-800-654-8483 (option 1), M-F, 7AM-8PM Central Time or www.byjasco.com if the unit should prove defective within the warranty period
WARNING
RISK OF FIRE
RISK OF ELECTRICAL SHOCK
RISK OF BURNS
TO REDUCE THE RISK OF ELECTRIC SHOCK, THIS PRODUCT HAS A GROUNDING PLUG THAT HAS A THIRD (GROUNDING) PIN THIS PLUG WILL ONLY FIT INTO A GROUNDING TYPE POWER OUTLET IF THE
PLUG DOES NOT FIT INTO OUTLET, CONTACT A QUALIFIED ELECTRICIAN TO INSTALL THE PROPER OUTLET DO NOT CHANGE THE PLUG IN ANY WAY CONTROLLING APPLIANCES
CAUTION: TO REDUCE THE RISK OF OVERHEATING AND POSSIBLE DAMAGE TO
OTHER EQUIPMENT

• DO NOT EXCEED RATINGS
• DO NOT USE TO CONTROL ANY DEVICE WHERE UNINTENDED OPERATION COULD CAUSE UNSAFE CONDITIONS (HEAT LAMP, SUN LAMP, ETC)
• DO NOT USE WITH EXTENSION CORDS
• FOR INDOOR USE ONLY

FCC/IC

Suppliers Declaration of Conformity Model#: 76724 Jasco Products Co, 10 E Memorial Rd, Oklahoma City, OK 73114, www.byjascocom
This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions:

1. this device may not cause harmful interference, and
2. this device must accept any interference received, including interference that may cause undesired operation

FCC NOTE: The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment. Such modifications could void the user’s authority to operate the equipment NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures

• Reorient or relocate the receiving antenna Increase the separation between the equipment and receiver
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected
• Consult the dealer or an experienced radio/ TV technician for help

CAN ICES-5KB)/NMB-5(B)

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>