better bathrooms BeBa_26699 Chrome Bath Mixer Tap User Manual

better bathrooms BeBa_26699 Chrome Bath Mixer Tap

The Deck Bath Mixer is a versatile plumbing fixture designed for use in the bathroom. It is used to control the flow and temperature of water for filling the bath and/or operating a shower. The mixer comes with various components, including a deck mixer, base plates (if provided), washers, back nuts, and a bath (purchased separately). It is important to follow the installation instructions and maintenance guidelines to ensure proper functionality and longevity of the product.

Guarantee
This product comes with a guarantee. However, the guarantee may be void if installation is not carried out as per the provided guide and correct maintenance instructions are not followed. Please refer to our website for detailed terms and conditions.

Parts

• Deck mixer
• Base plate x 2 (if provided)
• Bath (purchased separately)
• Washer x 2
• Back nut x 2

Tools Required
Before starting the installation process, make sure you have the following tools:

• Tool 1
• Tool 2
• Tool 3

Product Usage Instructions: Deck Bath Mixer Installation
Note: Before starting the installation of a new mixer, turn off the water supply. The HOT supply should be on the left and the COLD supply should be on the right.

1. Remove back nuts (5) and washers (4) if they are already fitted to the mixer.

2. If provided, place base plates (2) onto the mixer tails.

3. Place the mixer tails through the tap holes in the bath (3) (which should measure 180mm center to center).

4. From underneath the bath, fit the washers (4) and back nuts (5), then tighten into position.

5. Connect to the water supply, making a watertight seal in the process.

6. Turn on the water supply and check for leaks.
   Note: If you are installing a bath shower mixer with a handset and holder, follow these additional steps: Secure the holder to the wall in a position that allows the hose to hang freely

7. Fit seals to both ends of the hose

8. Connect the cone end of the hose to the handset and the nut end to the mixer outlet. Tighten securely.

Important: Always ensure that when fitting the bath shower mixer with a handset holder, the holder is positioned so as not to put the shower hose under tension. The hose should hang freely from the mixer outlet.

Troubleshooting
If you encounter any issues with your Deck Bath Mixer, refer to The following troubleshooting tips:

Mixer Drips After Being Turned Off

1. Draining: Due to the design of some mixer spouts, water may be held and drip until emptied.
2. Debris Inside the Valve: Remove the valve and flush it under running water while turning the spindle.

Poor Water Flow

1. Insufficient Water Pressure: Increase water pressure, possibly by installing a pump.
2. System Pressure: Ensure the system pressure meets the minimum requirement pre-installation.
3. Blockage: Check if water is reaching the mixer and inspect the valve, mixer tails, and supply pipes for any blockages.
4. Isolation Valves: Ensure that the isolation valves are fully opened.

Water Not Mixing

1. Hot and Cold Supplies: Balance the pressures of the hot and cold supplies by increasing or decreasing pressures (always maintain the minimum pressure requirement).
2. Blockage: Check if water is reaching the mixer and inspect the valve, mixer tails, and supply pipes for any blockages.

Mixer Not Diverting Correctly (If a Lift and Drop Type Diverter)

1. Insufficient Water Pressure: Increase water pressure, possibly by installing a pump.
2. System Pressure: Ensure the system pressure meets the minimum requirement pre-installation.
3. Your Mixer may be a Twist and Lock Diverter: Lift the handle, pull, and twist to lock it into position.

Maintenance
Note: Ensure to turn off the water supply to the mixer prior to any maintenance.

Note: The design of valve removal may vary. Please refer to the user manual for specific instructions.

Design A

If you need further assistance or have any questions, please contact our customer support.

Deck Bath Mixer

Please note: The image is for illustrative purposes only and may differ slightly from the actual product

• Single-person assembly
• Tools required
• We always recommend using professional tradespeople to install your product

Congratulations on your purchase
Welcome to our growing gang of savvy shoppers We’re on a mission to bring you extraordinary bathroom products, for less. From modern to traditional style ceramics, plus the gorgeous fixtures, fittings, and furniture to match. So, you can fall in love with your space every single day. As one of the UK’s largest independent bathroom stores, we’ve received countless awards; including the National Business Awards UK, the Digital Entrepreneur Awards, and being placed on The Sunday Times Fast Track 100. We hope your new product exceeds your highest expectations. However, if you experience any problems, please: Call our friendly UK call center on 0871 244 0935 (9 am-7 pm Monday to Friday, or 10am-4 pm Saturday and Sunday), or Send us a message via customerservices@buyitdirect.co.uk

Important information

• Please read these instructions thoroughly and retain them for future reference.
• All installation work must be carried out to comply by a qualified installer.
• Always check pressure compatibility, and check the website for min/maximum pressure of the product.
• Pressures to hot and cold supplies should be balanced for optimum performance.
• All installation work must be carried out to comply with the Water Bylaw Regulations.
• Isolation valves should be fitted to both supply pipes as part of the installation
• The system must be flushed through prior to installation.

Guarantee

• Please check our website for individual product guarantees.
• Some parts of the product, i.e. valve/diverter, are covered by a 12-month guarantee.
• Your guarantee can be invalid if the pre-installation checks are not carried out, installation is not carried out as per this guide, and correct maintenance instructions are not followed. Please see our website for T & C’s.

Parts
Please note: The image is for illustrative purposes only and may differ slightly from the actual product

1. Deck mixer
2. Base plate x 2 (if provided)
3. Bath (purchased separately)
4. Washer x 2
5. Back nut x 2

Installation

Please note: Before starting the installation of a new mixer, turn off the water supply
Please note : HOT supply to the left and COLD supply to the right

1. Remove back nuts (5) and washers (4) if they are already fitted to the mixer.
2. Place base plates (2) if provided, onto the mixer tails.
3. Place the mixer tails through the tap holes in the bath (3) (which should measure 180mm center to center).
4. From underneath the bath, fit the washers (4) and back nuts (5) then tighten them into position.
5. Connect to the water supply, making a watertight seal in the process.
6. Turn on the water supply and check for leaks

Please note : The image is for illustrative purposes only and may differ slightly to the actual product
If installing a bath shower mixer with handset and holder

1.  Secure the holder to the wall in a position that will allow the hose to hang freely.
2. Fit seals to both ends of the hose.
3. Connect the cone end of the hose to the handset and the nut end to the mixer outlet and tighten.

IMPORTANT
Always ensure when fitting a bath shower mixer with a handset holder, that the holder is positioned so as not to put the shower hose under tension. The hose should hang freely from the mixer outlet (as shown below).

Troubleshooting

Mixer drips after being turned off

1. Draining – Due to the design of some mixer spouts, water will be held and drip until emptied.
2. Debris inside the valve – remove the valve and flush under running water while turning the spindle.

Poor water flow

1. Insufficient water pressure – increase water pressure possibly installing a pump.
2. System pressure should meet the minimum requirement pre-installation.
3. Blockage – Check water is reaching the mixer, check valve, mixer tails, and supply pipes.
4. Isolation valves not fully opened.

Water not mixing

1. Hot and Cold supplies not balanced – increase or decrease pressures to balance. (Always maintain the minimum pressure requirement)
2. Blockage – Check water is reaching the mixer, check the valve, mixer tails, and supply pipes.

Mixer not diverting correctly (If a lift and drop type diverter)

1. Insufficient water pressure – increase water pressure possibly installing a pump.
2. System pressure should meet the minimum requirement pre-installation.
3. Your mixer may be a twist and lock diverter – lift the handle, pull, and twist to lock into position.

Maintenance
Valve removal for various designs
IMPORTANT: Ensure to turn off the water supply to the mixer prior to any maintenance
Please note: Design may vary from those shown below

Design A

1. Remove the screw cap cover. (This could be at the front or back of the handle)
2. Loosen the grub screw using a hex key.
3. Pull the handle from the mixer.
4. Remove insert (If included in your product).
5. Using a spanner, remove the valve.
6. Carry out maintenance.
7. Replace the valve and tighten it.
8. Replace all components.

Design B

1. Unscrew all handle pegs
2. Remove grub screws using a hex key
3. Pull the head section from the mixer
4. Remove extended screw
5. Unscrew shroud
6. Using a spanner remove the valve
7. Carry out maintenance.
8. Replace the valve and tighten it.
9. Replace all components.

Design C

1. Remove H or C indicator
2. Using a screwdriver remove the handle screw
3. Pull the handle from the mixer
4. Unscrew shroud
5. Using a spanner remove the valve
6. Carry out maintenance
7. Replace valve and tighten
8. Replace all components

Design D

1. Remove H or C indicator
2. Using a screwdriver remove the handle screw
3. Pull the handle from the mixer
4. Unscrew shroud
5. Using a spanner remove the valve
6. Carry out maintenance
7. Replace valve and tighten
8. Replace all components

Cleaning

To maintain the surface finish of your product, wipe it clean regularly, using a clean damp cloth and dry cloth to polish. Do not use abrasive cleaning agents or materials on the product surface as you may invalidate your guarantee. Should any harsh chemicals come into contact with the surface of the product during bathroom cleaning, rinse off immediately, wipe clean, and dry.

For more informatio n
visit betterbathrooms.com

• email customerservices@buyitdirect.co.uk
• call 0871 244 0935
• write to Trident Business Park, Neptune Way, Huddersfield, HD2 1UA

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>