CHILLOUT QUANTUM PRO Cooler Driver Cooling System Installation Guide

CHILLOUT QUANTUM PRO Cooler Driver Cooling System

REGISTER YOUR SYSTEM

| To activate your warranty, scan the provided QR code or navigate to https://chilloutsystems.com/pages/product-registration.
Products must be registered within 30 Days of purchase.
---|---

INCLUDED

• 1x Quantum Pro Cooler
• 1x Wiring harness
• 1x Carbon fiber baseplate
• 2x Quick release pins
• 4x Rubber isolators

SPECIFICATIONS

| RATED COOLING CAPACITY
400 watts
---|---
| WORKING VOLTAGE
12V/24V
| MAX CURRENT
30A/15A
| COMPRESSOR
Micro Brushless Inverter Rated Voltage: 24V
| FAN
Axial Flow Rated Voltage: 24V
| PUMP
Rated Voltage: 24V Max Flow: 20L/min
| RESEVOIR
Volume: 320ml
| SIZE
Length: 12.32in / 313mm
Width: 6.69in / 170mm
| WEIGHT
Cooler: 9.92lbs / 4.5kg
Mounting Plate: 6oz / 170gms
| OPERATING TEMPERATURE
32°F – 130°F / 0°C – 54.4°C
| STORAGE TEMPERATURE
14°F – 140°F / 0°C – 60°C

SYSTEM DISPLAY

The Quantum Pro Cooler can be controlled via the buttons on the system or by wired remote (sold separately).

BUTTON SETTINGS

| ON|OFF
Long press to turn the system On/Off.
---|---
| Mode Selection (Short Press)
ECO Mode: System performs at its lowest settings. Continues to cool with minimum amp draw.
MAX MODE: System automaticaly adjusts performance, chilling to the Set Temp.
| Increase System Temperature
Short press to switch to the fluid temperature setting. Press again to increase the fluid’s temperature (Increments of 5 degrees fahrenheit).
| Decrease System Temperature
Short press to switch to the fluid temperature setting. Press again to decrease the fluid’s temperature (Increments of 5 degrees farenheit).

MOUNTING THE BASEPLATE

• Determine the best location to mount your system inside the car. Keep  your system away from any heat sources to ensure maximum cooling efficiency. Ensure there is a sufficient gap between the back of the unit so that the air can circulate freely.
• Using the systems baseplate as a guide, carefully outline the preferred install location.
• Drill out the holes so that you can install the rivnuts to the vehicle.
  Once the rivnuts are installed, you can attach the base plate to the vehicle. Install the provided rubber isolators between the base plate and the installed rivnuts to keep airflow underneath the unit.

DUCTING AND PLENUMS

When installing a NACA duct and plenum, consider using ChillOut Systems 4 inch ducting and plenums. With nearly twice the airflow as 3 inch ducting, this is the most efficient way to keep your system cool. In some cases 3 inch ducting may be the only option. In this case, the system must be paired with a in-line 3 inch blower that is rated to 275 cfm..

• Place the NACA Duct and use marker or liquid chalk to trace an outline to the vehicle. Once the outline has been traced onto your window, a rotary cutting tool can be used to cut out the outline.
  We recommend using M4 nuts and bolts to secure the NACA duct to a lexan window

BATTERY TERMINAL LAYOUTS

Please use the following as a reference when advising the terminal layout required for your battery.

• When determining the terminal layout always face the terminal side (terminals closest to you) to avoid confusion / misinterpretation.
• Once you figure out the length of wire required you can trim the excess and connect it accordingly. (Our wiring harness uses 8 AWG wire)
• Connect the remote wire to the system if you have purchased a remote. We recommend putting the remote somewhere that sun won’t directly glare onto it (This can make it hard to read while driving).

CONNECTING THE SHIRT

• If you are using a dual prong connector, run the insulated hose from the system to where the driver seat is, making sure there is enough slack to reach the drivers shirt comfortably.
• If you are using Chillout Systems Rapid Release Kit , you can either cut and install it to a regular insulated hose or use our Insultated Y-Split Hose.
• When using a Y-Split hose, we recommend keeping a dual prong connector on one side of the seat and installing the rapid release on the opposite side giving you both options in the car for connecting the shirts to the system.

Note: The system display will light up the icon when connected to the shirt correctly. If there is a connection issue or the system stops unexpectedly, the icon will begin flashing.

FILLING THE RESEVOIR

• Mix 1 part Chillout System’s Coolant Formula to 4 parts deionized water (1:4)
• Open the cap and slowly pour into the resevoir until the fluid is visible in the filling port. Be mindful of the pouring speed and do not let the liquid overflow.
• Press and hold the power button on the display for 2 seconds to power on the system. You will need to top up the fluid as it cycles through the system until visible again in the filling port.
• When turning the system on for the first time, the fluid level will decrease due to the systems internal lines containg no fluid.

Note: If you are using an alternative antifreeze solution, its viscosity at 40°F / 25°C should not exceed 2.2mPa·s. Purified water is also suitable fluid for the system if Chillout Systems Coolant Formula is not available.

SYSTEM FAULT CODES

If the system experiences a fault, it will automatically shut down. The fault code will appear in the Current Temp location on the systems display.

(E1) Temperature Sensor Failure
The systems temperature sensor has an error or the systems temperature has exceeded its monitoring range (-22~ 392°F/-30~200°C).

(E2) Low voltage protection
Compressor input voltage is too low.

Note: The system has a low-voltage protection function. If the vehicles battery is used as the power supply and the input voltage is lower than the protection voltage (9V~10V), the system will automatically shut down. When the power supply voltage returns to normal, the host will automatically turn on after 30 seconds.

(E3) Lack of phase
A phase line of the compressor has become faulty

Note: The system has a overcurrent protection function. If the current is greater than the protection current (about 35A), the system will automatically shut down. After the current protection occurs, the system will need to be powered on manually

SYSTEM OVERHEATING

• Warning symbols will show on the display when the internal temperature of the system exceeds its optimal operating temperatures. Power off the system immediately and allow for the system to cool before restarting.

Note: Restart time after overheating is between 3-5 minutes.

DIMENSIONS

SERVICING

• Deep cleaning of all internals (includes fans, condenser, controller boards).
• Servicing of the cooling system.
• Freon pressure check and top-up (if necessary).
• Performance checks and optimization.

REPAIR/REPLACEMENT

In the unlikely event of a failure to your system, within your extended warranty we will expedite a replacement cooler to you via Express Air Service.

Your system will be diagnosed, serviced, repaired, and sent back to you.

References

• Product Registration – CHILLOUT SYSTEMS

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>