Ovutek VSW530-KUS Digital Body Weight Scale User Manual

Ovutek VSW530-KUS Digital Body Weight Scale

Product Information

The DIY Handcrafted Rock Fountain Kits are designed to make the installation of your Handcrafted GFRC Fountain Bubbler Rock Kit easy. These kits are compatible with GFRC Handcrafted Rock DIY Kits using 2×2 or 4×4 Basins. The kits include all the necessary tools and components for installation, including GFRC Fountain Bubbler Rock(s), Flexible Polymesh, Grate, Flexible Hose, Plumbing Fitting or Manifold for Doubles and Triples High-Efficiency Water Pump, and Water Basin Reservoir.
Subscribe to our YouTube channel, BlueThumbINC, for related informational videos.

Product Usage Instructions

Step 1: Choose Your Fountain Basin Location

When selecting a location for your fountain, ensure that it is large enough to accommodate the basin and any possible water overspray from wind. Avoid placing the basin near vegetation or structures that are not suitable for excessively wet conditions. Place the basin/reservoir in the chosen location and use a shovel or marker paint to outline the ground around the basin. Before excavation begins, be sure to call MISS DIG or your utility company.

Step 2: Dig the Fountain Basin Hole

Follow the outline and dig a hole deep enough for the basin. The top edge of the basin should extend above the ground by about 1 inch. If the soil is unstable, dig the hole 3 inches deeper and back-fill with 3 inches of crushed rock or gravel to provide a solid foundation. Ensure that the ground is level before adding your basin.

Step 3: Placement and Leveling the Fountain Basin

Insert the fountain basin into the hole and use a level to ensure that it is level from front-to-back and side-to-side. Note that near one corner of the basin, there is a spinweld fitting installed. This corner should face the direction of your electrical outlet as it is where the pump will be installed. Rotate the basin until the corner with the spinweld is in the desired location. Place grates with the corner grate piece over the pump for access.

Optional Auto Fill Kit Install

If you are incorporating an Auto Fill Kit, you may bury your water supply line and make any Auto Fill connections at this time. The Auto Fill Kit item number is #ABDAUTO.

Step 4: Backfill Around the Basin

Use the previously removed soil to backfill around the fountain basin. Tamp the dirt tightly to prevent future settling. It is recommended to leave the basin covered while backfilling to prevent dirt from falling into the reservoir.

Step 5: Install the Pump and Plumbing

Thread the included fitting onto the pump discharge, then hand-tighten one end of the hose to the grey union on the pump. Set the pump inside the basin (it can be laid on its side if necessary). If you have a double or triple fountain system, there will be a manifold system attached to the pump to regulate water flow to each bubbler.

Step 6: Install Grate and Polymesh Screen

Place the grate on top of the basin with the triangular corner access panel over the pump. If you have a 2×2 basin, you will have a single grate.

Digital Body Weight Scale
Model : VSW530-KUS

Thank you for purchasing the Digital Body Weight Scale by Ovutek.
If you have any questions or concerns, please reach out to our helpful Customer Support Team at service@ovutek.com. We hope you enjoy your new scale

Package Contents

• 1 x Digital Body Weight Scale
• 4 x 1.5V AAA Batteries
• 1 x Quick Start Guide

Specifications

Increments

| 100 g(0.2lb) ≤m＜ 10 kg(22lb)| D=0.05 lb / 0.02 kg
10 kg(22lb) ≤m≤ 205 kg(450lb)| D=0.1 lb / 0.05 kg
Weight Units| lb / kg / st
Minimum weight value| 0.2 lb / 100 g
Platform| Tempered Glass
Power Supply| 4 x 1.5V AAA Batteries
Auto- Off| 5 / 10 / 30 seconds
Dimensions| 11.8 x 11.8 x 1.0 in / 30.0 x 30.0 x 2.55 cm
Weight| 3.9 lb / 1.8 kg

READ AND SAVE THESE INSTRUCTIONS

Safety Information

Please read and follow all instructions and safety guidelines in this manual.

General Use

• Check the scale before using. Do not use the scale if it is damaged in any way.
• Do not strike or bang on the scale and do not use the scale if there is a slight crack on the glass. Due to the nature of tempered glass, the glass will shatter if there is a slight crack. If you see a crack, contact Customer Support (see page 15).
• The glass platform is slippery when wet. Always make sure the platform and your feet are dry before stepping onto theCVscale.
• Place the scale on a hard, flat surface.
• To weigh safely and accurately, stand with your feet shoulder
  • width apart while on the scale. Do not stand on the edge of the scale or jump on the scale.
• Avoid standing on the scale for a long period of time.
• Do not overload the scale. Maximum weight capacity is 450 lb / 205 kg / 32 st.
• Keep the scale in a cool area with low humidity. Keep the scale away from heat sources, such as ovens or heaters.
• Store the scale horizontally, not vertically.
• For household use only. This scale is not intended for commercial use.
• Handle with care

Batteries

• Do not mix new and old batteries.
• If the scale is not in use for a long period of time, remove the batteries to extend the lifetime of the scale.

Function Diagram

• A. Display
• B. Platform
• C. Anti-Skid Padding
• D. Unit Conversion Button
• E. Battery Compartment

Before First Use

1. Take out the AAA battery included in the box.
2. Open the battery compartment on the underside of the scale.
3. Install the batteries. Follow the guidelines in the battery compartment to match the + and – terminals.

Operation

Using the Scale
Press the unit conversion button on the underside of the scale to switch units between pounds (lb) , stone(st) and kilograms (kg).

1. Place the scale on a hard, flat surface.
   Note :Using the scale on soft surfaces such as carpets and mats will result in inaccurate measurements.

2. Stand on the scale until the display flashes several times, showing your final measurement.

3. Measure Light Items
   Measure items as light as 100 g, like packages or fruits, with pinpoint accuracy. When“ ”is displayed , a minimum of 100 g can be weighed.[Figure 1.4 ]

Measure Again

• Step off the scale.[Figure 1.1]
• Lights up to confirm the result is accurate.[Figure 1.2] and “Err” will display to remind the result maybe inaccurate due to some reason, we recommend you re-measure.[Figure 1.3]

Family Mode

Replacing the Batteries

1. Open the battery compartment on the underside of the scale.
2. Remove the old batteries and dispose of them properly.
3. Install 4 new 1.5V AAA batteries. Make sure the polarities match.
4. Close the battery compartment, place the scale on a hard, flat surface.

Cleaning the Scale

1. Use a slightly damp cloth to clean the surface of the scale, followed by a soft, dry cloth to wipe away the remaining moisture.
2. Do not use chemical or abrasive cleaning agents to clean the scale.

Troubleshooting

Federal Communication Commission Interference Statement

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired operation.

NOTE : This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help. FCC Caution:Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment

FCC SDOC SUPPLIER’S DECLARATION OF CONFORMITY

Etekcity Corporation hereby declares that this equipment is in compliance with the FCC Part 15 Subpart B. The declaration of conformity may be consulted in the support section of our website, accessible from www.etekcity.com

Warranty Information

TERMS & POLICY

Ovutek warrants this product to the original purchaser to be free from defects in material and workmanship, under normal use and conditions, for a period of 2 years from the date of original purchase. Ovutek agrees, at our option during the warranty period, to repair any defect in material or workmanship or furnish an equal product in exchange without charge, subject to verification of the defect or malfunction and proof of the date of purchase.

There is no other express warranty. This warranty does not apply:

• If the product has been modified from its original condition;
• If the product has not been used in accordance with directions and instructions in the user manual;
• To damages or defects caused by accident, abuse, misuse or improper or inadequate maintenance;
• To damages or defects caused by service or repair of the product performed by an unauthorized service provider or by anyone other than Ovutek ;
• To damages or defects occurring during commercial use, rental use, or any use for which the product is not intended;
• To damages or defects exceeding the cost of the product

Ovutek will not be liable for indirect, incidental, or consequential damages in connection with the use of the product covered by this warranty. This warranty extends only to the original consumer purchaser of the product and is not transferable to any subsequent owner of the product regardless of whether the product is transferred during the specified term of the warranty. This warranty does not extend to products purchased from unauthorized sellers. Ovutek ’s warranty extends only to products purchased from authorized sellers that are subject to Ovutek ’s quality controls and have agreed to follow its quality controls.
All implied warranties are limited to the period of this limited warranty. This warranty gives you specific legal rights and you may also have other rights which vary from state to state. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you.
If you discover that your product is defective within the specified warranty period, please contact Customer Support via service@ovutek.com. DO NOT dispose of your product before contacting us. Once our Customer Support Team has approved your request, please return the product with a copy of the invoice and order ID.
Every Ovutek product automatically includes a 2-year warranty. This warranty is made by: Ovutek
This warranty is made by: Ovutek Corporation

Customer Support

If you encounter any issues or have any questions regarding your new product, please contact our helpful Customer Support Team. Ovutek Corporation
Email : service@ovutek.com
Please have your order invoice and order ID ready before contacting Customer Support.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>