saxby lighting 60899 Nico Shaver Mirror Instruction Manual
- June 12, 2024
- saxby lighting
Table of Contents
Instruction leaflet
Nico Mirror
60899
60899 Nico Shaver Mirror
Thank you for purchasing this light fitting. Please read the instructions
carefully before use to ensure safe and satisfactory operation of this
product. Please retain these instructions for future reference.
Warning
This is a Class 1 product and must be earthed Please read these
instructions carefully before commencing any work.
This unit must be fitted by a competent and qualified electrician.
Installin accordance with EE Wiring regulations and current Building
Regulations.
To prevent electrocution switch off at mains supply before installing or
maintaining this fitting. Ensure other persons cannot restore the electrical
supply without your knowledge.
This light fitting should be connected to a fused circuit.
If replacing an existing ftting, meke a careful note of the connections.
This system contains non-replaceable parts and cannot be serviced.
If damage occurs the part should be scrapped.
This product is not suitable for dimming.
This product is rated at IP44.
This product contains a demister pad. If this pad is damaged in anyway then it
should be replaced by a qualfied electrician.
Waste electrical products should not be disposed of with household waste.
Please recycle where facilities exist. Check with your local authority or
retailer for recycling advice.
Caution: To avoid interference, the sensor must be placed a minimum of 200mm
away form any surface of object.
Specification
Voltage: 220-240V~ 50Hz
Lamp: 10W LED module (SMD), 4000K
IP rating: 44
Shaver socket: 115V-240V dual socket
Layout
- Cables in walls must be protected using suitable conduit or plastic trunking
- The mains supply cable must have a minimum cross sectional area of 1.0mm.
- This product has special protection against the ingress of moisture and is IP44 rated.
- This product is fitted with a no touch infra- red switch, helping to keep the mirror clear of fingerprints. When installing the product, the sensor switch must be at least 150mm from an adjacent wall or obstruction to ensure the switch can function properly.
This
product is suitable for use in zone 1, zone 2 and outside zones of a bathroom
only.
Please see diagram.
If this unit is being fitted in a room containing a bath or shower, a 30mA RCD
must be used – in accordance with IEE regulations.
Installation
Existing fittings must be completely removed before installation of a new product. Before removing the existing fitting, carefully note the position of each set of wires.
- Undo the screws (two on each side of the fiting) and remove the front mirror assembly and set aside
- Hold the back plate in place and mark the position of the fixing holes. Ensure that the product is level.
- Ensure the wall is capable of holding the weight of the product. Take care to avoid damaging any concealed wiring and pipes. The correct fixings should be used for brick, cavity walls or plasterboard.
- Pierce grommet and pass the supply cable through the hole in the wall back.
- Fix the product into position.
Wiring
Having correctly identified the wiring from your existing ligt fiting, connect
to the connection block inside the product in the following way: 
Check that…
- You have correctly identified the wires
- The connections are tight
- No loose strands have been left out of the connection block.
Commissioning
- Push the labelled male and female connectors together to power the demister pad.
- Refit the mirror front onto the wall back. Ensure that the seals are correctly located before securing with the four screws.
- Replace fuse or circuit breaker and switch on. Your light is now ready for use.
- Activate your new LED mirror by swiping your hand in front of the sensor.
Shaver Socket Instructions
- The shaver socket is powered by a 20W isolating transformer and is only intended for use with electric shavers, electric toothbrush chargers and similar products.
- Any appliance connected to the socket must not exceed the 20W power output as this could cause damage and overheating to occur.
- Always check your appliance instructions to ensure the power requirements are less than 20W.
Demister Operation
- Simply turn on the demister switch on the side. The demister pad will warm the mirror surface.
- The demisting effect will spread approximately 10 – 20% further than the pad itself.
- We recommend cleaning with a soft dry cloth. Do not use solvents or abrasive cleaners as these could damage the finish.
- Mirror – Use a damp cloth or a propriety glass cleaner. Do not use abrasive materials as these will damage the finish.
Recycling advice
Waste electrical products should not be disposed of with household waste. Please recycle where facilities Exist. Check with your Local Authority or retailer for recycling advice.
Safety information
Live Voltages may be present i this unit even when tuned of or when completely
disconnected. For your safety, always switch off the power supply before
changing lightbulbs, or cleaning.
The mirror must be replaced immediately should it become cracked or damaged.
This fiting must not be used without the mirror in place.
UK Manufacturer: BH17 7BY
EU Manufacturer:
Briiant AG,
Briliantsirasse 1, D-27442 Gnarrenburg
V3 28/10/2021
www.saxbylighting.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>