ALTOBEAM ATBM6062 WiFi and Bluetooth Module User Manual

ALTOBEAM ATBM6062 WiFi and Bluetooth Module

Product Information

User Manual ATBM6062 Wi-Fi and BLE Module
ATBM6062 module is a highly integrated 1T1R 802.11/b/g/n/ax and Bluetooth LE v5.0 device with USB interface (USB 2.0 compliant), based on AltoBeam’s ATBM6062-U IC chip.

Main Specifications:

• Main chipset: ATBM6062-U
• Operating frequency: 2.4GHz
• Wi-Fi Standard: 802.11/b/g/n/ax
• BLE Standard: Bluetooth LE v5.0
• Wi-Fi Modulation: Coded-PHY, S=2 and S=8
• Wi-Fi Bandwidth: HT20 and HT40
• Wi-Fi PHY data rates: 1Mbps, 2Mbps, 6Mbps, 11Mbps, 54Mbps
• Wi-Fi sensitivity: -99.5dBm, -96.0dBm (1Mbps, 2Mbps), -101.5dBm (Coded-PHY, S=2), -106.0dBm (Coded-PHY, S=8)
• Wi-Fi transmitting power: Varies based on channel and mode
• BLE transmitting power: Varies based on channel and mode
• BLE sensitivity: -25dB to -35dB (varies based on channel and mode)
• Host interface: USB 2.0
• Operation range: More than 150 meters in open space
• RF antenna: External antenna (2.4GHz 50Ohm Resistance)
• Security: WEP, WPA, WPA2, WPA3 personal
• Power consumption: Max. 330mA at DC3.3V
• Operating temperature: -40°C to +85°C
• Storage temperature: -50°C to +125°C
• Humidity: 5% to 90% maximum (non-condensing)
• Dimension: L13.00W12.20H1.70mm

Mechanical Specification

Outline drawing:

The typical dongle size is L64.0W16.0H7.0mm.

Wi-Fi RF Performance

Typical RF output power:

Typical EVM:

DISCLAIMER
Information in this document is provided in connection with AltoBeam products. No license, express or implied, by estoppels or otherwise, to any intellectual property rights is granted by this document. Except as provided in AltoBeam’s terms and conditions of sale for such products, AltoBeam assumes no liability whatsoever, and AltoBeam disclaims any express or implied warranty, relating to sale and/or use of AltoBeam products including liability or warranties relating to fitness for a particular purpose, merchantability, or infringement of any patent, copyright or other intellectual property right.

AltoBeam may make changes to specifications and product descriptions at any time, without notice.

Designers must not rely on the absence or characteristics of any features or instructions marked “reserved” or “undefined.” AltoBeam reserves these for future definition and shall have no responsibility whatsoever for conflicts or incompatibilities arising from future changes to them. Unauthorized use of information contained herein, disclosure or distribution to any third party without written permission of AltoBeam is prohibited. AltoBeam™ is the trademark of AltoBeam. All other trademarks and product names are properties of their respective owners.

Copyright © 2007~2023 AltoBeam Inc., all rights reserved

CONTACT INFORMATION

AltoBeam Inc.

• Address: B808, Tsinghua Tongfang Hi-Tech Plaza, Haidian, Beijing 100083
• Tel : (8610) 6270 1811
• Fax : (8610) 6270 1830
• Website: www.altobeam.com
• Support : support@altobeam.com

REVISION HISTORY

Revision

Number

| Revision

Date

| Changes
---|---|---
Item| Description
1.0| 2023-03-06| | Formal release

Overview

ATBM6062 module is a highly integrated 1T1R 802.11/b/g/n/ax and Bluetooth LE v5.0 device with USB interface (USB 2.0 compliant), based on AltoBeam’s ATBM6062-U IC chip.

802.11g/n/ax: OFDM

Wi-Fi Bandwidth| 802.11b/g/n/ax 20MHz: ≤20MHz

802.11n/ax 40MHz: ≤40MHz

Wi-Fi PHY data rates

| 802.11b: 1, 2, 5, 11Mbps

802.11g: 6, 9, 12, 18, 24, 36, 48, 54Mbps

802.11n: MSC0~7, up to 150Mbps 802.11ax: MSC0~11, up to 286.8Mbps

Wi-Fi sensitivity

| 802.11b 1Mbps: -97.5dBm; 802.11b 11Mbps: -90.0dBm;

802.11g 6Mbps: -93.5dBm; 802.11g 54Mbps: -76.5dBm;

802.11n MSC7 HT20: -74.0dBm; 802.11n MSC7 HT40: -71.0dBm

802.11ax MSC11 HE20: -64.0dBm; 802.11ax MSC11 HE40: -60.5dBm

Wi-Fi transmitting power

| 802.11b 1Mbps: 18dBm; 802.11b 11Mbps: 18dBm; 802.11g 6Mbps: 17dBm; 802.11g 54Mbps: 15dBm;

802.11n HT20 MSC7: 14dBm; 802.11n HT40 MCS7: 14dBm;

802.11ax HT20 MSC11: 13dBm; 802.11ax HT40 MSC11: 13dBm

BLE transmitting power| 10dBm
BLE sensitivity| 1Mbps: -99.5dBm; 2Mbps: -96.0dBm; Coded-PHY, S=2: -101.5dBm;

Coded-PHY, S=8: -106.0dBm

---|---
Host interface| USB 2.0
Operation range| More than 150 meters in open space
RF antenna| External antenna (2.4GHz 50Ohm Resistance)
Security| WEP, WPA, WPA2, WPA3 personal
Power consumption| DC3.3V Max.330mA
Operating temperature| -40 ~ +85℃ ambient temperature
Storage temperature| -50~ +125℃ ambient temperature
Humidity| 5% to 90% maximum (non-condensing)
Dimension| Typical L13.00W12.20H1.70mm

Mechanical Specification ****

Outline drawing
The typical dongle size is L64.0W16.0H7.0mm.

Wi-Fi RF Performance

Typical RF output power

Mode| Data Rate| Unit| Channel 1| Channel 6| Channel 11
---|---|---|---|---|---
802.11b| 1Mbps| ****

dBm

| 18| 18| 18
11Mbps| 18| 18| 18
802.11g| 6Mbps| 17| 17| 17
54Mbps| 15| 15| 15
802.11n| MSC7_HT20| 14| 14| 14
MSC7_HT40| 14| 14| 14

802.11ax

| MSC0_HE20| 17| 17| 17
MSC0_HE40| 17| 17| 17
MSC11_HE20| 13| 13| 13
MSC11_HE40| 13| 13| 13

Typical EVM

Mode| Data Rate| Unit| Channel 1| Channel 6| Channel 11
---|---|---|---|---|---
802.11b| 1Mbps| ****

dB

| -25| -25| -25
11Mbps| -25| -25| -25
802.11g| 6Mbps| -25| -25| -25
54Mbps| -30| -30| -30
802.11n| MSC7_HT20| -30| -30| -30
MSC7_HT40| -30| -30| -30

802.11ax

| MSC0_HE20| -25| -25| -25
MSC0_HE40| -25| -25| -25
MSC11_HE20| -35| -35| -35
MSC11_HE40| -35| -35| -35

Center frequency tolerance

ppm

| -10| ±2| +10
802.11g| 54Mbps| -10| ±2| +10
802.11n| MSC7| -10| ±2| +10
802.11ax| MSC11| | -10| ±2| +10
---|---|---|---|---|---

Receiver sensitivity

Mode| Data Rate| Unit| Channel 1| Channel 6| Channel 11
---|---|---|---|---|---
802.11b| 1Mbps| ****

dBm

| -97.5| -97.5| -97.5
11Mbps| -90.0| -90.0| -90.0
802.11g| 6Mbps| -93.5| -93.5| -93.5
54Mbps| -76.5| -76.5| -76.5
802.11n| MSC7_HT20| -74.0| -74.0| -74.0
MSC7_HT40| -71.0| -71.0| -71.0
802.11ax| MSC11_HE20| -64.0| -64.0| -64.0
MSC11_HE40| -60.5| -60.5| -60.5

BLE RF performance

Receiver Sensitivity

| 1Mbps| | -99.5| | dBm
2Mbps| | -96.0| | dBm
Coded-PHY, S=2| | -101.5| | dBm
Coded-PHY, S=8| | -106.0| | dBm

**Solder Reflow Profile

**

Referred to IPC/JEDEC standard. Peak Temperature: <260℃ Number of Times: ≤2 times

Pre-heat

| Minimal temperature (Tsmin)| 150℃
Maximal temperature (Tsmax)| 200℃
Time (ts)| 60~120 seconds
Time maintained above| Temperature (TL)| 217℃
Time (tL)| 40~60 seconds
Peak/Classification temperature (TP)| 260℃
Time within 5℃ of actual peak temperature (tP)| 10~20 seconds
Ramp-down rate| 2.5℃/second max.
Time 25℃ to peak temperature| 8 minutes max.

Packing Information

• Packing : Tape and Reel
• MPQ (Minimum Packing Quantity): 1,700pcs

Warning

1. Do not use this product under humid or hot
2. Do not use
3. FCC compliance statement

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Warning : Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

List of applicable FCC Rules:

• 47 CFR Part 15, Subpart C 15.203
• 47 CFR Part 15,Subpart C 15.205
• 47 CFR Part 15,Subpart C 15.207
• 47 CFR Part 15,Subpart C 15.209
• 47 CFR Part 15,Subpart C 15.247
• 47 CFR Part 2.109 1

Summarize the specific operational use conditions
This module can be used in IOT devices, the input voltage to the module is nominally 5V.

Limited module procedures
This module is not a limited module.

Trace antenna designs
The antenna is not a trace antenna.

RF Exposure compliance statement
This Module complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator and your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

Labelling Instruction for Host Product Integrator
Please notice that if the FCC identification number is not visible when the module is installed inside another device, then the outside of the device into which the module is installed must also display a label referring to the enclosed module. This exterior label can use wording such as the following: “Contains FCC ID: 2BAVSATBM6062” any similar wording that expresses the same meaning may be used.

15.19 Labelling requirements shall be complied on end user device. Labelling rules for special device, please refer to §2.925, § 15.19 (a)(5) and relevant KDB publications. For E-label, please refer to §2.935 Information on test modes and additional testing requirements Please see the last page

The OEM integrator is responsible for ensuring that the end-user has no manual instruction to remove or install module.

The module is limited to installation in mobile application, a separate approval is required for all other operating configurations, including portable configurations with respect to §2.1093 and difference antenna configurations.

Antenna Change Notice to Host manufacturer
If you desire to increase antenna gain and either change antenna type or use same antenna type certified, a Class II permissive change application is required to be filed by us, or you (host manufacturer) can take responsibility through the change in FCC ID (new application) procedure followed by a Class II permissive change application.

Test software
AltoBeam WLAN Faciliry SZ 1.0.8

FCC other Parts, Part 15B Compliance Requirements for Host Product Manufacturer

This modular transmitter is only FCC authorized for the specific rule parts listed on our grant, host product manufacturer is responsible for compliance to any other FCC rules that apply to the host not covered by the modular transmitter grant of certification. Host manufacturer in any case shall ensure host product which is installed and operating with the module is in compliant with Part 15B requirements.

Please note that For a Class B or Class A digital device or peripheral, the instructions furnished the user manual of the end-user product shall include statement set out in §15.105 Information to the user or such similar statement and place it in a prominent location in the text of host product manual. Original texts as following:

For Class B

Note : This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

For Class A

Note : This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.

Information on test modes and additional testing requirements Test Software: AltoBeam WLAN Faciliry SZ 1.0.8 Load the chip and select the corresponding channel, mode, bandwidth, etc. for testing.

• Frequencies: BLE 2402MHz to 2480MHz; WLAN 802.11b/g/n(HT20)/ax(HEW20): 2412MHz to 2462MHz; 802.11n(HT40)/ax(HEW40): 2422MHz to 2452MHz
• Modulation Type: BLE GFSK; WLAN 802.11b: DS (CCK, DQPSK, DBPSK); 802.11g/n: OFDM (64QAM, 16QAM, QPSK, BPSK); 802.11ax: OFDMA(16QAM, 64QAM, 256QAM, 1024QAM, QPSK, BPSK)

References

• 高拓讯达

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>